| 1 | |
| 2 | |
| 3 | * TI/National Semiconductor LP3943 PWM driver
|
| 4 | *
|
| 5 | * Copyright 2013 Texas Instruments
|
| 6 | *
|
| 7 | * Author: Milo Kim <[email protected]>
|
| 8 |
|
| 9 |
|
| 10 | #include <linux/err.h>
|
| 11 | #include <linux/mfd/lp3943.h>
|
| 12 | #include <linux/module.h>
|
| 13 | #include <linux/of.h>
|
| 14 | #include <linux/platform_device.h>
|
| 15 | #include <linux/pwm.h>
|
| 16 | #include <linux/slab.h>
|
| 17 |
|
| 18 | #define LP3943_MAX_DUTY 255
|
| 19 | #define LP3943_MIN_PERIOD 6250
|
| 20 | #define LP3943_MAX_PERIOD 1600000
|
| 21 |
|
| 22 | struct lp3943_pwm {
|
| 23 | struct lp3943 *lp3943;
|
| 24 | struct lp3943_platform_data *pdata;
|
| 25 | struct lp3943_pwm_map pwm_map[LP3943_NUM_PWMS];
|
| 26 | };
|
| 27 |
|
| 28 | static inline struct lp3943_pwm *to_lp3943_pwm(struct pwm_chip *chip)
|
| 29 | {
|
| 30 | return pwmchip_get_drvdata(chip);
|
| 31 | }
|
| 32 |
|
| 33 | static struct lp3943_pwm_map *
|
| 34 | lp3943_pwm_request_map(struct lp3943_pwm *lp3943_pwm, int hwpwm)
|
| 35 | {
|
| 36 | struct lp3943_platform_data *pdata = lp3943_pwm->pdata;
|
| 37 | struct lp3943 *lp3943 = lp3943_pwm->lp3943;
|
| 38 | struct lp3943_pwm_map *pwm_map = &lp3943_pwm->pwm_map[hwpwm];
|
| 39 | int i, offset;
|
| 40 |
|
| 41 | pwm_map->output = pdata->pwms[hwpwm]->output;
|
| 42 | pwm_map->num_outputs = pdata->pwms[hwpwm]->num_outputs;
|
| 43 |
|
| 44 | for (i = 0; i < pwm_map->num_outputs; i++) {
|
| 45 | offset = pwm_map->output[i];
|
| 46 |
|
| 47 |
|
| 48 | if (test_and_set_bit(offset, &lp3943->pin_used))
|
| 49 | return ERR_PTR(-EBUSY);
|
| 50 | }
|
| 51 |
|
| 52 | return pwm_map;
|
| 53 | }
|
| 54 |
|
| 55 | static int lp3943_pwm_request(struct pwm_chip *chip, struct pwm_device *pwm)
|
| 56 | {
|
| 57 | struct lp3943_pwm *lp3943_pwm = to_lp3943_pwm(chip);
|
| 58 | struct lp3943_pwm_map *pwm_map;
|
| 59 |
|
| 60 | pwm_map = lp3943_pwm_request_map(lp3943_pwm, pwm->hwpwm);
|
| 61 | if (IS_ERR(pwm_map))
|
| 62 | return PTR_ERR(pwm_map);
|
| 63 |
|
| 64 | return 0;
|
| 65 | }
|
| 66 |
|
| 67 | static void lp3943_pwm_free_map(struct lp3943_pwm *lp3943_pwm,
|
| 68 | struct lp3943_pwm_map *pwm_map)
|
| 69 | {
|
| 70 | struct lp3943 *lp3943 = lp3943_pwm->lp3943;
|
| 71 | int i, offset;
|
| 72 |
|
| 73 | for (i = 0; i < pwm_map->num_outputs; i++) {
|
| 74 | offset = pwm_map->output[i];
|
| 75 | clear_bit(offset, &lp3943->pin_used);
|
| 76 | }
|
| 77 | }
|
| 78 |
|
| 79 | static void lp3943_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm)
|
| 80 | {
|
| 81 | struct lp3943_pwm *lp3943_pwm = to_lp3943_pwm(chip);
|
| 82 | struct lp3943_pwm_map *pwm_map = &lp3943_pwm->pwm_map[pwm->hwpwm];
|
| 83 |
|
| 84 | lp3943_pwm_free_map(lp3943_pwm, pwm_map);
|
| 85 | }
|
| 86 |
|
| 87 | static int lp3943_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
|
| 88 | u64 duty_ns, u64 period_ns)
|
| 89 | {
|
| 90 | struct lp3943_pwm *lp3943_pwm = to_lp3943_pwm(chip);
|
| 91 | struct lp3943 *lp3943 = lp3943_pwm->lp3943;
|
| 92 | u8 val, reg_duty, reg_prescale;
|
| 93 | int err;
|
| 94 |
|
| 95 | |
| 96 | * How to configure the LP3943 PWMs
|
| 97 | *
|
| 98 | * 1) Period = 6250 ~ 1600000
|
| 99 | * 2) Prescale = period / 6250 -1
|
| 100 | * 3) Duty = input duty
|
| 101 | *
|
| 102 | * Prescale and duty are register values
|
| 103 |
|
| 104 |
|
| 105 | if (pwm->hwpwm == 0) {
|
| 106 | reg_prescale = LP3943_REG_PRESCALE0;
|
| 107 | reg_duty = LP3943_REG_PWM0;
|
| 108 | } else {
|
| 109 | reg_prescale = LP3943_REG_PRESCALE1;
|
| 110 | reg_duty = LP3943_REG_PWM1;
|
| 111 | }
|
| 112 |
|
| 113 | |
| 114 | * Note that after this clamping, period_ns fits into an int. This is
|
| 115 | * helpful because we can resort to integer division below instead of
|
| 116 | * the (more expensive) 64 bit division.
|
| 117 |
|
| 118 | period_ns = clamp(period_ns, (u64)LP3943_MIN_PERIOD, (u64)LP3943_MAX_PERIOD);
|
| 119 | val = (u8)((int)period_ns / LP3943_MIN_PERIOD - 1);
|
| 120 |
|
| 121 | err = lp3943_write_byte(lp3943, reg_prescale, val);
|
| 122 | if (err)
|
| 123 | return err;
|
| 124 |
|
| 125 | duty_ns = min(duty_ns, period_ns);
|
| 126 | val = (u8)((int)duty_ns * LP3943_MAX_DUTY / (int)period_ns);
|
| 127 |
|
| 128 | return lp3943_write_byte(lp3943, reg_duty, val);
|
| 129 | }
|
| 130 |
|
| 131 | static int lp3943_pwm_set_mode(struct lp3943_pwm *lp3943_pwm,
|
| 132 | struct lp3943_pwm_map *pwm_map,
|
| 133 | u8 val)
|
| 134 | {
|
| 135 | struct lp3943 *lp3943 = lp3943_pwm->lp3943;
|
| 136 | const struct lp3943_reg_cfg *mux = lp3943->mux_cfg;
|
| 137 | int i, index, err;
|
| 138 |
|
| 139 | for (i = 0; i < pwm_map->num_outputs; i++) {
|
| 140 | index = pwm_map->output[i];
|
| 141 | err = lp3943_update_bits(lp3943, mux[index].reg,
|
| 142 | mux[index].mask,
|
| 143 | val << mux[index].shift);
|
| 144 | if (err)
|
| 145 | return err;
|
| 146 | }
|
| 147 |
|
| 148 | return 0;
|
| 149 | }
|
| 150 |
|
| 151 | static int lp3943_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
|
| 152 | {
|
| 153 | struct lp3943_pwm *lp3943_pwm = to_lp3943_pwm(chip);
|
| 154 | struct lp3943_pwm_map *pwm_map = &lp3943_pwm->pwm_map[pwm->hwpwm];
|
| 155 | u8 val;
|
| 156 |
|
| 157 | if (pwm->hwpwm == 0)
|
| 158 | val = LP3943_DIM_PWM0;
|
| 159 | else
|
| 160 | val = LP3943_DIM_PWM1;
|
| 161 |
|
| 162 | |
| 163 | * Each PWM generator is set to control any of outputs of LP3943.
|
| 164 | * To enable/disable the PWM, these output pins should be configured.
|
| 165 |
|
| 166 |
|
| 167 | return lp3943_pwm_set_mode(lp3943_pwm, pwm_map, val);
|
| 168 | }
|
| 169 |
|
| 170 | static void lp3943_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
|
| 171 | {
|
| 172 | struct lp3943_pwm *lp3943_pwm = to_lp3943_pwm(chip);
|
| 173 | struct lp3943_pwm_map *pwm_map = &lp3943_pwm->pwm_map[pwm->hwpwm];
|
| 174 |
|
| 175 | |
| 176 | * LP3943 outputs are open-drain, so the pin should be configured
|
| 177 | * when the PWM is disabled.
|
| 178 |
|
| 179 |
|
| 180 | lp3943_pwm_set_mode(lp3943_pwm, pwm_map, LP3943_GPIO_OUT_HIGH);
|
| 181 | }
|
| 182 |
|
| 183 | static int lp3943_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
|
| 184 | const struct pwm_state *state)
|
| 185 | {
|
| 186 | int err;
|
| 187 |
|
| 188 | if (state->polarity != PWM_POLARITY_NORMAL)
|
| 189 | return -EINVAL;
|
| 190 |
|
| 191 | if (!state->enabled) {
|
| 192 | if (pwm->state.enabled)
|
| 193 | lp3943_pwm_disable(chip, pwm);
|
| 194 | return 0;
|
| 195 | }
|
| 196 |
|
| 197 | err = lp3943_pwm_config(chip, pwm, state->duty_cycle, state->period);
|
| 198 | if (err)
|
| 199 | return err;
|
| 200 |
|
| 201 | if (!pwm->state.enabled)
|
| 202 | err = lp3943_pwm_enable(chip, pwm);
|
| 203 |
|
| 204 | return err;
|
| 205 | }
|
| 206 |
|
| 207 | static const struct pwm_ops lp3943_pwm_ops = {
|
| 208 | .request = lp3943_pwm_request,
|
| 209 | .free = lp3943_pwm_free,
|
| 210 | .apply = lp3943_pwm_apply,
|
| 211 | };
|
| 212 |
|
| 213 | static int lp3943_pwm_parse_dt(struct device *dev,
|
| 214 | struct lp3943_pwm *lp3943_pwm)
|
| 215 | {
|
| 216 | static const char * const name[] = { "ti,pwm0", "ti,pwm1", };
|
| 217 | struct device_node *node = dev->of_node;
|
| 218 | struct lp3943_platform_data *pdata;
|
| 219 | struct lp3943_pwm_map *pwm_map;
|
| 220 | enum lp3943_pwm_output *output;
|
| 221 | int i, err, num_outputs, count = 0;
|
| 222 |
|
| 223 | if (!node)
|
| 224 | return -EINVAL;
|
| 225 |
|
| 226 | pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
|
| 227 | if (!pdata)
|
| 228 | return -ENOMEM;
|
| 229 |
|
| 230 | |
| 231 | * Read the output map configuration from the device tree.
|
| 232 | * Each of the two PWM generators can drive zero or more outputs.
|
| 233 |
|
| 234 |
|
| 235 | for (i = 0; i < LP3943_NUM_PWMS; i++) {
|
| 236 | num_outputs = of_property_count_u32_elems(node, name[i]);
|
| 237 | if (num_outputs <= 0)
|
| 238 | continue;
|
| 239 |
|
| 240 | output = devm_kcalloc(dev, num_outputs, sizeof(*output),
|
| 241 | GFP_KERNEL);
|
| 242 | if (!output)
|
| 243 | return -ENOMEM;
|
| 244 |
|
| 245 | err = of_property_read_u32_array(node, name[i], output,
|
| 246 | num_outputs);
|
| 247 | if (err)
|
| 248 | return err;
|
| 249 |
|
| 250 | pwm_map = devm_kzalloc(dev, sizeof(*pwm_map), GFP_KERNEL);
|
| 251 | if (!pwm_map)
|
| 252 | return -ENOMEM;
|
| 253 |
|
| 254 | pwm_map->output = output;
|
| 255 | pwm_map->num_outputs = num_outputs;
|
| 256 | pdata->pwms[i] = pwm_map;
|
| 257 |
|
| 258 | count++;
|
| 259 | }
|
| 260 |
|
| 261 | if (count == 0)
|
| 262 | return -ENODATA;
|
| 263 |
|
| 264 | lp3943_pwm->pdata = pdata;
|
| 265 | return 0;
|
| 266 | }
|
| 267 |
|
| 268 | static int lp3943_pwm_probe(struct platform_device *pdev)
|
| 269 | {
|
| 270 | struct lp3943 *lp3943 = dev_get_drvdata(pdev->dev.parent);
|
| 271 | struct pwm_chip *chip;
|
| 272 | struct lp3943_pwm *lp3943_pwm;
|
| 273 | int ret;
|
| 274 |
|
| 275 | chip = devm_pwmchip_alloc(&pdev->dev, LP3943_NUM_PWMS, sizeof(*lp3943_pwm));
|
| 276 | if (IS_ERR(chip))
|
| 277 | return PTR_ERR(chip);
|
| 278 | lp3943_pwm = to_lp3943_pwm(chip);
|
| 279 |
|
| 280 | lp3943_pwm->pdata = lp3943->pdata;
|
| 281 | if (!lp3943_pwm->pdata) {
|
| 282 | if (IS_ENABLED(CONFIG_OF))
|
| 283 | ret = lp3943_pwm_parse_dt(&pdev->dev, lp3943_pwm);
|
| 284 | else
|
| 285 | ret = -ENODEV;
|
| 286 |
|
| 287 | if (ret)
|
| 288 | return ret;
|
| 289 | }
|
| 290 |
|
| 291 | lp3943_pwm->lp3943 = lp3943;
|
| 292 | chip->ops = &lp3943_pwm_ops;
|
| 293 |
|
| 294 | return devm_pwmchip_add(&pdev->dev, chip);
|
| 295 | }
|
| 296 |
|
| 297 | #ifdef CONFIG_OF
|
| 298 | static const struct of_device_id lp3943_pwm_of_match[] = {
|
| 299 | { .compatible = "ti,lp3943-pwm" },
|
| 300 | { }
|
| 301 | };
|
| 302 | MODULE_DEVICE_TABLE(of, lp3943_pwm_of_match);
|
| 303 | #endif
|
| 304 |
|
| 305 | static struct platform_driver lp3943_pwm_driver = {
|
| 306 | .probe = lp3943_pwm_probe,
|
| 307 | .driver = {
|
| 308 | .name = "lp3943-pwm",
|
| 309 | .of_match_table = of_match_ptr(lp3943_pwm_of_match),
|
| 310 | },
|
| 311 | };
|
| 312 | module_platform_driver(lp3943_pwm_driver);
|
| 313 |
|
| 314 | MODULE_DESCRIPTION("LP3943 PWM driver");
|
| 315 | MODULE_ALIAS("platform:lp3943-pwm");
|
| 316 | MODULE_AUTHOR("Milo Kim");
|
| 317 | MODULE_LICENSE("GPL");
|