projects/linux·blob master · refs

205 lines · 7.2 KiB

1/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause) */
2/*
3 * This file is provided under a dual BSD/GPLv2 license. When using or
4 * redistributing this file, you may do so under either license.
5 *
6 * Copyright(c) 2018 Intel Corporation
7 */
8
9#ifndef __INCLUDE_SOUND_SOF_DAI_INTEL_H__
10#define __INCLUDE_SOUND_SOF_DAI_INTEL_H__
11
12#include <sound/sof/header.h>
13
14 /* ssc1: TINTE */
15#define SOF_DAI_INTEL_SSP_QUIRK_TINTE (1 << 0)
16 /* ssc1: PINTE */
17#define SOF_DAI_INTEL_SSP_QUIRK_PINTE (1 << 1)
18 /* ssc2: SMTATF */
19#define SOF_DAI_INTEL_SSP_QUIRK_SMTATF (1 << 2)
20 /* ssc2: MMRATF */
21#define SOF_DAI_INTEL_SSP_QUIRK_MMRATF (1 << 3)
22 /* ssc2: PSPSTWFDFD */
23#define SOF_DAI_INTEL_SSP_QUIRK_PSPSTWFDFD (1 << 4)
24 /* ssc2: PSPSRWFDFD */
25#define SOF_DAI_INTEL_SSP_QUIRK_PSPSRWFDFD (1 << 5)
26/* ssc1: LBM */
27#define SOF_DAI_INTEL_SSP_QUIRK_LBM (1 << 6)
28
29 /* here is the possibility to define others aux macros */
30
31#define SOF_DAI_INTEL_SSP_FRAME_PULSE_WIDTH_MAX 38
32#define SOF_DAI_INTEL_SSP_SLOT_PADDING_MAX 31
33
34/* SSP clocks control settings
35 *
36 * Macros for clks_control field in sof_ipc_dai_ssp_params struct.
37 */
38
39/* mclk 0 disable */
40#define SOF_DAI_INTEL_SSP_MCLK_0_DISABLE BIT(0)
41/* mclk 1 disable */
42#define SOF_DAI_INTEL_SSP_MCLK_1_DISABLE BIT(1)
43/* mclk keep active */
44#define SOF_DAI_INTEL_SSP_CLKCTRL_MCLK_KA BIT(2)
45/* bclk keep active */
46#define SOF_DAI_INTEL_SSP_CLKCTRL_BCLK_KA BIT(3)
47/* fs keep active */
48#define SOF_DAI_INTEL_SSP_CLKCTRL_FS_KA BIT(4)
49/* bclk idle */
50#define SOF_DAI_INTEL_SSP_CLKCTRL_BCLK_IDLE_HIGH BIT(5)
51/* mclk early start */
52#define SOF_DAI_INTEL_SSP_CLKCTRL_MCLK_ES BIT(6)
53/* bclk early start */
54#define SOF_DAI_INTEL_SSP_CLKCTRL_BCLK_ES BIT(7)
55/* mclk always on */
56#define SOF_DAI_INTEL_SSP_CLKCTRL_MCLK_AON BIT(8)
57
58/* DMIC max. four controllers for eight microphone channels */
59#define SOF_DAI_INTEL_DMIC_NUM_CTRL 4
60
61/* SSP Configuration Request - SOF_IPC_DAI_SSP_CONFIG */
62struct sof_ipc_dai_ssp_params {
63 struct sof_ipc_hdr hdr;
64 uint16_t reserved1;
65 uint16_t mclk_id;
66
67 uint32_t mclk_rate; /* mclk frequency in Hz */
68 uint32_t fsync_rate; /* fsync frequency in Hz */
69 uint32_t bclk_rate; /* bclk frequency in Hz */
70
71 /* TDM */
72 uint32_t tdm_slots;
73 uint32_t rx_slots;
74 uint32_t tx_slots;
75
76 /* data */
77 uint32_t sample_valid_bits;
78 uint16_t tdm_slot_width;
79 uint16_t reserved2; /* alignment */
80
81 /* MCLK */
82 uint32_t mclk_direction;
83
84 uint16_t frame_pulse_width;
85 uint16_t tdm_per_slot_padding_flag;
86 uint32_t clks_control;
87 uint32_t quirks;
88 uint32_t bclk_delay; /* guaranteed time (ms) for which BCLK
89 * will be driven, before sending data
90 */
91} __packed;
92
93/* HDA Configuration Request - SOF_IPC_DAI_HDA_CONFIG */
94struct sof_ipc_dai_hda_params {
95 struct sof_ipc_hdr hdr;
96 uint32_t link_dma_ch;
97 uint32_t rate;
98 uint32_t channels;
99} __packed;
100
101/* ALH Configuration Request - SOF_IPC_DAI_ALH_CONFIG */
102struct sof_ipc_dai_alh_params {
103 struct sof_ipc_hdr hdr;
104 uint32_t stream_id;
105 uint32_t rate;
106 uint32_t channels;
107
108 /* reserved for future use */
109 uint32_t reserved[13];
110} __packed;
111
112/* DMIC Configuration Request - SOF_IPC_DAI_DMIC_CONFIG */
113
114/* This struct is defined per 2ch PDM controller available in the platform.
115 * Normally it is sufficient to set the used microphone specific enables to 1
116 * and keep other parameters as zero. The customizations are:
117 *
118 * 1. If a device mixes different microphones types with different polarity
119 * and/or the absolute polarity matters the PCM signal from a microphone
120 * can be inverted with the controls.
121 *
122 * 2. If the microphones in a stereo pair do not appear in captured stream
123 * in desired order due to board schematics choises they can be swapped with
124 * the clk_edge parameter.
125 *
126 * 3. If PDM bit errors are seen in capture (poor quality) the skew parameter
127 * that delays the sampling time of data by half cycles of DMIC source clock
128 * can be tried for improvement. However there is no guarantee for this to fix
129 * data integrity problems.
130 */
131struct sof_ipc_dai_dmic_pdm_ctrl {
132 struct sof_ipc_hdr hdr;
133 uint16_t id; /**< PDM controller ID */
134
135 uint16_t enable_mic_a; /**< Use A (left) channel mic (0 or 1)*/
136 uint16_t enable_mic_b; /**< Use B (right) channel mic (0 or 1)*/
137
138 uint16_t polarity_mic_a; /**< Optionally invert mic A signal (0 or 1) */
139 uint16_t polarity_mic_b; /**< Optionally invert mic B signal (0 or 1) */
140
141 uint16_t clk_edge; /**< Optionally swap data clock edge (0 or 1) */
142 uint16_t skew; /**< Adjust PDM data sampling vs. clock (0..15) */
143
144 uint16_t reserved[3]; /**< Make sure the total size is 4 bytes aligned */
145} __packed;
146
147/* This struct contains the global settings for all 2ch PDM controllers. The
148 * version number used in configuration data is checked vs. version used by
149 * device driver src/drivers/dmic.c need to match. It is incremented from
150 * initial value 1 if updates done for the to driver would alter the operation
151 * of the microphone.
152 *
153 * Note: The microphone clock (pdmclk_min, pdmclk_max, duty_min, duty_max)
154 * parameters need to be set as defined in microphone data sheet. E.g. clock
155 * range 1.0 - 3.2 MHz is usually supported microphones. Some microphones are
156 * multi-mode capable and there may be denied mic clock frequencies between
157 * the modes. In such case set the clock range limits of the desired mode to
158 * avoid the driver to set clock to an illegal rate.
159 *
160 * The duty cycle could be set to 48-52% if not known. Generally these
161 * parameters can be altered within data sheet specified limits to match
162 * required audio application performance power.
163 *
164 * The microphone clock needs to be usually about 50-80 times the used audio
165 * sample rate. With highest sample rates above 48 kHz this can relaxed
166 * somewhat.
167 *
168 * The parameter wake_up_time describes how long time the microphone needs
169 * for the data line to produce valid output from mic clock start. The driver
170 * will mute the captured audio for the given time. The min_clock_on_time
171 * parameter is used to prevent too short clock bursts to happen. The driver
172 * will keep the clock active after capture stop if this time is not yet
173 * met. The unit for both is microseconds (us). Exceed of 100 ms will be
174 * treated as an error.
175 */
176struct sof_ipc_dai_dmic_params {
177 struct sof_ipc_hdr hdr;
178 uint32_t driver_ipc_version; /**< Version (1..N) */
179
180 uint32_t pdmclk_min; /**< Minimum microphone clock in Hz (100000..N) */
181 uint32_t pdmclk_max; /**< Maximum microphone clock in Hz (min...N) */
182
183 uint32_t fifo_fs; /**< FIFO sample rate in Hz (8000..96000) */
184 uint32_t reserved_1; /**< Reserved */
185 uint16_t fifo_bits; /**< FIFO word length (16 or 32) */
186 uint16_t fifo_bits_b; /**< Deprecated since firmware ABI 3.0.1 */
187
188 uint16_t duty_min; /**< Min. mic clock duty cycle in % (20..80) */
189 uint16_t duty_max; /**< Max. mic clock duty cycle in % (min..80) */
190
191 uint32_t num_pdm_active; /**< Number of active pdm controllers. */
192 /**< Range is 1..SOF_DAI_INTEL_DMIC_NUM_CTRL */
193
194 uint32_t wake_up_time; /**< Time from clock start to data (us) */
195 uint32_t min_clock_on_time; /**< Min. time that clk is kept on (us) */
196 uint32_t unmute_ramp_time; /**< Length of logarithmic gain ramp (ms) */
197
198 /* reserved for future use */
199 uint32_t reserved[5];
200
201 /**< PDM controllers configuration */
202 struct sof_ipc_dai_dmic_pdm_ctrl pdm[SOF_DAI_INTEL_DMIC_NUM_CTRL];
203} __packed;
204
205#endif