| 1 | # |
| 2 | # This config is an example usage of ktest.pl with a kvm guest |
| 3 | # |
| 4 | # The guest is called 'Guest' and this would be something that |
| 5 | # could be run on the host to test a virtual machine target. |
| 6 | |
| 7 | MACHINE = Guest |
| 8 | |
| 9 | |
| 10 | # Use virsh to read the serial console of the guest |
| 11 | CONSOLE = virsh console ${MACHINE} |
| 12 | |
| 13 | # Use SIGKILL to terminate virsh console. We can't kill virsh console |
| 14 | # by the default signal, SIGINT. |
| 15 | CLOSE_CONSOLE_SIGNAL = KILL |
| 16 | |
| 17 | #*************************************# |
| 18 | # This part is the same as test.conf # |
| 19 | #*************************************# |
| 20 | |
| 21 | # The include files will set up the type of test to run. Just set TEST to |
| 22 | # which test you want to run. |
| 23 | # |
| 24 | # TESTS = patchcheck, randconfig, boot, test, config-bisect, bisect, min-config |
| 25 | # |
| 26 | # See the include/*.conf files that define these tests |
| 27 | # |
| 28 | TEST := patchcheck |
| 29 | |
| 30 | # Some tests may have more than one test to run. Define MULTI := 1 to run |
| 31 | # the extra tests. |
| 32 | MULTI := 0 |
| 33 | |
| 34 | # In case you want to differentiate which type of system you are testing |
| 35 | BITS := 64 |
| 36 | |
| 37 | # REBOOT = none, error, fail, empty |
| 38 | # See include/defaults.conf |
| 39 | REBOOT := empty |
| 40 | |
| 41 | |
| 42 | # The defaults file will set up various settings that can be used by all |
| 43 | # machine configs. |
| 44 | INCLUDE include/defaults.conf |
| 45 | |
| 46 | |
| 47 | #*************************************# |
| 48 | # Now we are different from test.conf # |
| 49 | #*************************************# |
| 50 | |
| 51 | |
| 52 | # The example here assumes that Guest is running a Fedora release |
| 53 | # that uses dracut for its initfs. The POST_INSTALL will be executed |
| 54 | # after the install of the kernel and modules are complete. |
| 55 | # |
| 56 | POST_INSTALL = ${SSH} /sbin/dracut -f /boot/initramfs-test.img $KERNEL_VERSION |
| 57 | |
| 58 | # Guests sometimes get stuck on reboot. We wait 3 seconds after running |
| 59 | # the reboot command and then do a full power-cycle of the guest. |
| 60 | # This forces the guest to restart. |
| 61 | # |
| 62 | POWERCYCLE_AFTER_REBOOT = 3 |
| 63 | |
| 64 | # We do the same after the halt command, but this time we wait 20 seconds. |
| 65 | POWEROFF_AFTER_HALT = 20 |
| 66 | |
| 67 | |
| 68 | # As the defaults.conf file has a POWER_CYCLE option already defined, |
| 69 | # and options can not be defined in the same section more than once |
| 70 | # (all DEFAULTS sections are considered the same). We use the |
| 71 | # DEFAULTS OVERRIDE to tell ktest.pl to ignore the previous defined |
| 72 | # options, for the options set in the OVERRIDE section. |
| 73 | # |
| 74 | DEFAULTS OVERRIDE |
| 75 | |
| 76 | # Instead of using the default POWER_CYCLE option defined in |
| 77 | # defaults.conf, we use virsh to cycle it. To do so, we destroy |
| 78 | # the guest, wait 5 seconds, and then start it up again. |
| 79 | # Crude, but effective. |
| 80 | # |
| 81 | POWER_CYCLE = virsh destroy ${MACHINE}; sleep 5; virsh start ${MACHINE} |
| 82 | |
| 83 | |
| 84 | DEFAULTS |
| 85 | |
| 86 | # The following files each handle a different test case. |
| 87 | # Having them included allows you to set up more than one machine and share |
| 88 | # the same tests. |
| 89 | INCLUDE include/patchcheck.conf |
| 90 | INCLUDE include/tests.conf |
| 91 | INCLUDE include/bisect.conf |
| 92 | INCLUDE include/min-config.conf |
| 93 | INCLUDE include/bootconfig.conf |