diff --git a/Documentation/ABI/testing/sysfs-class-led-trigger-netdev b/Documentation/ABI/testing/sysfs-class-led-trigger-netdev index f6d9d72..a6c307c 100644 --- a/Documentation/ABI/testing/sysfs-class-led-trigger-netdev +++ b/Documentation/ABI/testing/sysfs-class-led-trigger-netdev @@ -114,6 +114,45 @@ Description: speed of 1000Mbps of the named network device. Setting this value also immediately changes the LED state. +What: /sys/class/leds//link_2500 +Date: Nov 2023 +KernelVersion: 6.8 +Contact: linux-leds@vger.kernel.org +Description: + Signal the link speed state of 2500Mbps of the named network device. + + If set to 0 (default), the LED's normal state is off. + + If set to 1, the LED's normal state reflects the link state + speed of 2500Mbps of the named network device. + Setting this value also immediately changes the LED state. + +What: /sys/class/leds//link_5000 +Date: Nov 2023 +KernelVersion: 6.8 +Contact: linux-leds@vger.kernel.org +Description: + Signal the link speed state of 5000Mbps of the named network device. + + If set to 0 (default), the LED's normal state is off. + + If set to 1, the LED's normal state reflects the link state + speed of 5000Mbps of the named network device. + Setting this value also immediately changes the LED state. + +What: /sys/class/leds//link_10000 +Date: Nov 2023 +KernelVersion: 6.8 +Contact: linux-leds@vger.kernel.org +Description: + Signal the link speed state of 10000Mbps of the named network device. + + If set to 0 (default), the LED's normal state is off. + + If set to 1, the LED's normal state reflects the link state + speed of 10000Mbps of the named network device. + Setting this value also immediately changes the LED state. + What: /sys/class/leds//half_duplex Date: Jun 2023 KernelVersion: 6.5 diff --git a/Documentation/ABI/testing/sysfs-class-led-trigger-tty b/Documentation/ABI/testing/sysfs-class-led-trigger-tty index 2bf6b24..30cef9a 100644 --- a/Documentation/ABI/testing/sysfs-class-led-trigger-tty +++ b/Documentation/ABI/testing/sysfs-class-led-trigger-tty @@ -4,3 +4,59 @@ KernelVersion: 5.10 Contact: linux-leds@vger.kernel.org Description: Specifies the tty device name of the triggering tty + +What: /sys/class/leds//rx +Date: February 2024 +KernelVersion: 6.8 +Description: + Signal reception (rx) of data on the named tty device. + If set to 0, the LED will not blink on reception. + If set to 1 (default), the LED will blink on reception. + +What: /sys/class/leds//tx +Date: February 2024 +KernelVersion: 6.8 +Description: + Signal transmission (tx) of data on the named tty device. + If set to 0, the LED will not blink on transmission. + If set to 1 (default), the LED will blink on transmission. + +What: /sys/class/leds//cts +Date: February 2024 +KernelVersion: 6.8 +Description: + CTS = Clear To Send + DCE is ready to accept data from the DTE. + If the line state is detected, the LED is switched on. + If set to 0 (default), the LED will not evaluate CTS. + If set to 1, the LED will evaluate CTS. + +What: /sys/class/leds//dsr +Date: February 2024 +KernelVersion: 6.8 +Description: + DSR = Data Set Ready + DCE is ready to receive and send data. + If the line state is detected, the LED is switched on. + If set to 0 (default), the LED will not evaluate DSR. + If set to 1, the LED will evaluate DSR. + +What: /sys/class/leds//dcd +Date: February 2024 +KernelVersion: 6.8 +Description: + DCD = Data Carrier Detect + DTE is receiving a carrier from the DCE. + If the line state is detected, the LED is switched on. + If set to 0 (default), the LED will not evaluate CAR (DCD). + If set to 1, the LED will evaluate CAR (DCD). + +What: /sys/class/leds//rng +Date: February 2024 +KernelVersion: 6.8 +Description: + RNG = Ring Indicator + DCE has detected an incoming ring signal on the telephone + line. If the line state is detected, the LED is switched on. + If set to 0 (default), the LED will not evaluate RNG. + If set to 1, the LED will evaluate RNG. diff --git a/Documentation/devicetree/bindings/leds/allwinner,sun50i-a100-ledc.yaml b/Documentation/devicetree/bindings/leds/allwinner,sun50i-a100-ledc.yaml new file mode 100644 index 0000000..760cb33 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/allwinner,sun50i-a100-ledc.yaml @@ -0,0 +1,137 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/leds/allwinner,sun50i-a100-ledc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A100 LED Controller + +maintainers: + - Samuel Holland + +description: + The LED controller found in Allwinner sunxi SoCs uses a one-wire serial + interface to drive up to 1024 RGB LEDs. + +properties: + compatible: + oneOf: + - const: allwinner,sun50i-a100-ledc + - items: + - enum: + - allwinner,sun20i-d1-ledc + - allwinner,sun50i-r329-ledc + - const: allwinner,sun50i-a100-ledc + + reg: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus clock + - description: Module clock + + clock-names: + items: + - const: bus + - const: mod + + resets: + maxItems: 1 + + dmas: + maxItems: 1 + description: TX DMA channel + + dma-names: + const: tx + + allwinner,pixel-format: + description: Pixel format (subpixel transmission order), default is "grb" + enum: + - bgr + - brg + - gbr + - grb + - rbg + - rgb + + allwinner,t0h-ns: + default: 336 + description: Length of high pulse when transmitting a "0" bit + + allwinner,t0l-ns: + default: 840 + description: Length of low pulse when transmitting a "0" bit + + allwinner,t1h-ns: + default: 882 + description: Length of high pulse when transmitting a "1" bit + + allwinner,t1l-ns: + default: 294 + description: Length of low pulse when transmitting a "1" bit + + allwinner,treset-ns: + default: 300000 + description: Minimum delay between transmission frames + +patternProperties: + "^multi-led@[0-9a-f]+$": + type: object + $ref: leds-class-multicolor.yaml# + unevaluatedProperties: false + properties: + reg: + minimum: 0 + maximum: 1023 + description: Index of the LED in the series (must be contiguous) + + required: + - reg + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + +additionalProperties: false + +examples: + - | + #include + #include + + ledc: led-controller@2008000 { + compatible = "allwinner,sun20i-d1-ledc", + "allwinner,sun50i-a100-ledc"; + reg = <0x2008000 0x400>; + interrupts = <36 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu 12>, <&ccu 34>; + clock-names = "bus", "mod"; + resets = <&ccu 12>; + dmas = <&dma 42>; + dma-names = "tx"; + #address-cells = <1>; + #size-cells = <0>; + + multi-led@0 { + reg = <0x0>; + color = ; + function = LED_FUNCTION_INDICATOR; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/leds/awinic,aw200xx.yaml b/Documentation/devicetree/bindings/leds/awinic,aw200xx.yaml index feb5feb..54d6d1f 100644 --- a/Documentation/devicetree/bindings/leds/awinic,aw200xx.yaml +++ b/Documentation/devicetree/bindings/leds/awinic,aw200xx.yaml @@ -10,15 +10,19 @@ maintainers: - Martin Kurbanov description: | - This controller is present on AW20036/AW20054/AW20072. - It is a 3x12/6x9/6x12 matrix LED programmed via - an I2C interface, up to 36/54/72 LEDs or 12/18/24 RGBs, - 3 pattern controllers for auto breathing or group dimming control. + It is a matrix LED driver programmed via an I2C interface. Devices have + a set of individually controlled leds and support 3 pattern controllers + for auto breathing or group dimming control. Supported devices: + - AW20036 (3x12) 36 LEDs + - AW20054 (6x9) 54 LEDs + - AW20072 (6x12) 72 LEDs + - AW20108 (9x12) 108 LEDs For more product information please see the link below: aw20036 - https://www.awinic.com/en/productDetail/AW20036QNR#tech-docs aw20054 - https://www.awinic.com/en/productDetail/AW20054QNR#tech-docs aw20072 - https://www.awinic.com/en/productDetail/AW20072QNR#tech-docs + aw20108 - https://www.awinic.com/en/productDetail/AW20108QNR#tech-docs properties: compatible: @@ -26,6 +30,7 @@ properties: - awinic,aw20036 - awinic,aw20054 - awinic,aw20072 + - awinic,aw20108 reg: maxItems: 1 @@ -36,13 +41,11 @@ properties: "#size-cells": const: 0 - awinic,display-rows: - $ref: /schemas/types.yaml#/definitions/uint32 - description: - Leds matrix size + enable-gpios: + maxItems: 1 patternProperties: - "^led@[0-9a-f]$": + "^led@[0-9a-f]+$": type: object $ref: common.yaml# unevaluatedProperties: false @@ -60,16 +63,11 @@ patternProperties: since the chip has a single global setting. The maximum output current of each LED is calculated by the following formula: - IMAXled = 160000 * (592 / 600.5) * (1 / display-rows) + IMAXled = 160000 * (592 / 600.5) * (1 / max-current-switch-number) And the minimum output current formula: - IMINled = 3300 * (592 / 600.5) * (1 / display-rows) - -required: - - compatible - - reg - - "#address-cells" - - "#size-cells" - - awinic,display-rows + IMINled = 3300 * (592 / 600.5) * (1 / max-current-switch-number) + where max-current-switch-number is determinated by led configuration + and depends on how leds are physically connected to the led driver. allOf: - if: @@ -78,18 +76,67 @@ allOf: contains: const: awinic,aw20036 then: + patternProperties: + "^led@[0-9a-f]+$": + properties: + reg: + items: + minimum: 0 + maximum: 36 + + - if: properties: - awinic,display-rows: - enum: [1, 2, 3] - else: + compatible: + contains: + const: awinic,aw20054 + then: + patternProperties: + "^led@[0-9a-f]+$": + properties: + reg: + items: + minimum: 0 + maximum: 54 + + - if: properties: - awinic,display-rows: - enum: [1, 2, 3, 4, 5, 6, 7] + compatible: + contains: + const: awinic,aw20072 + then: + patternProperties: + "^led@[0-9a-f]+$": + properties: + reg: + items: + minimum: 0 + maximum: 72 + + - if: + properties: + compatible: + contains: + const: awinic,aw20108 + then: + patternProperties: + "^led@[0-9a-f]+$": + properties: + reg: + items: + minimum: 0 + maximum: 108 + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" additionalProperties: false examples: - | + #include #include i2c { @@ -101,7 +148,7 @@ examples: reg = <0x3a>; #address-cells = <1>; #size-cells = <0>; - awinic,display-rows = <3>; + enable-gpios = <&gpio 3 GPIO_ACTIVE_HIGH>; led@0 { reg = <0x0>; diff --git a/Documentation/devicetree/bindings/leds/common.yaml b/Documentation/devicetree/bindings/leds/common.yaml index c8d0ba5..55a8d13 100644 --- a/Documentation/devicetree/bindings/leds/common.yaml +++ b/Documentation/devicetree/bindings/leds/common.yaml @@ -167,7 +167,7 @@ properties: Note that this flag is mainly used for PWM-LEDs, where it is not possible to map brightness to current. Drivers for other controllers should use led-max-microamp. - $ref: /schemas/types.yaml#definitions/uint32 + $ref: /schemas/types.yaml#/definitions/uint32 panic-indicator: description: diff --git a/Documentation/devicetree/bindings/leds/qcom,spmi-flash-led.yaml b/Documentation/devicetree/bindings/leds/qcom,spmi-flash-led.yaml index a8736fd..1ba6076 100644 --- a/Documentation/devicetree/bindings/leds/qcom,spmi-flash-led.yaml +++ b/Documentation/devicetree/bindings/leds/qcom,spmi-flash-led.yaml @@ -89,9 +89,11 @@ additionalProperties: false examples: - | #include - spmi { + + pmic { #address-cells = <1>; #size-cells = <0>; + led-controller@ee00 { compatible = "qcom,pm8350c-flash-led", "qcom,spmi-flash-led"; reg = <0xee00>; diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig index 6292fdd..d721b25 100644 --- a/drivers/leds/Kconfig +++ b/drivers/leds/Kconfig @@ -95,14 +95,18 @@ config LEDS_ARIEL Say Y to if your machine is a Dell Wyse 3020 thin client. config LEDS_AW200XX - tristate "LED support for Awinic AW20036/AW20054/AW20072" + tristate "LED support for Awinic AW20036/AW20054/AW20072/AW20108" depends on LEDS_CLASS depends on I2C help - This option enables support for the AW20036/AW20054/AW20072 LED driver. - It is a 3x12/6x9/6x12 matrix LED driver programmed via - an I2C interface, up to 36/54/72 LEDs or 12/18/24 RGBs, - 3 pattern controllers for auto breathing or group dimming control. + This option enables support for the Awinic AW200XX LED controllers. + It is a matrix LED driver programmed via an I2C interface. Devices have + a set of individually controlled LEDs and support 3 pattern controllers + for auto breathing or group dimming control. Supported devices: + - AW20036 (3x12) 36 LEDs + - AW20054 (6x9) 54 LEDs + - AW20072 (6x12) 72 LEDs + - AW20108 (9x12) 108 LEDs To compile this driver as a module, choose M here: the module will be called leds-aw200xx. @@ -110,6 +114,7 @@ config LEDS_AW200XX config LEDS_AW2013 tristate "LED support for Awinic AW2013" depends on LEDS_CLASS && I2C && OF + select REGMAP_I2C help This option enables support for the AW2013 3-channel LED driver. @@ -298,6 +303,15 @@ config LEDS_COBALT_RAQ help This option enables support for the Cobalt Raq series LEDs. +config LEDS_SUN50I_A100 + tristate "LED support for Allwinner A100 RGB LED controller" + depends on LEDS_CLASS_MULTICOLOR + depends on ARCH_SUNXI || COMPILE_TEST + help + This option enables support for the RGB LED controller found + in some Allwinner sunxi SoCs, including A100, R329, and D1. + It uses a one-wire interface to control up to 1024 LEDs. + config LEDS_SUNFIRE tristate "LED support for SunFire servers." depends on LEDS_CLASS @@ -638,6 +652,17 @@ config LEDS_ADP5520 To compile this driver as a module, choose M here: the module will be called leds-adp5520. +config LEDS_MAX5970 + tristate "LED Support for Maxim 5970" + depends on LEDS_CLASS + depends on MFD_MAX5970 + help + This option enables support for the Maxim MAX5970 & MAX5978 smart + switch indication LEDs via the I2C bus. + + To compile this driver as a module, choose M here: the module will + be called leds-max5970. + config LEDS_MC13783 tristate "LED Support for MC13XXX PMIC" depends on LEDS_CLASS diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile index d7348e8..ce07dc2 100644 --- a/drivers/leds/Makefile +++ b/drivers/leds/Makefile @@ -56,6 +56,7 @@ obj-$(CONFIG_LEDS_LP8501) += leds-lp8501.o obj-$(CONFIG_LEDS_LP8788) += leds-lp8788.o obj-$(CONFIG_LEDS_LP8860) += leds-lp8860.o obj-$(CONFIG_LEDS_LT3593) += leds-lt3593.o +obj-$(CONFIG_LEDS_MAX5970) += leds-max5970.o obj-$(CONFIG_LEDS_MAX77650) += leds-max77650.o obj-$(CONFIG_LEDS_MAX8997) += leds-max8997.o obj-$(CONFIG_LEDS_MC13783) += leds-mc13783.o @@ -78,6 +79,7 @@ obj-$(CONFIG_LEDS_POWERNV) += leds-powernv.o obj-$(CONFIG_LEDS_PWM) += leds-pwm.o obj-$(CONFIG_LEDS_REGULATOR) += leds-regulator.o obj-$(CONFIG_LEDS_SC27XX_BLTC) += leds-sc27xx-bltc.o +obj-$(CONFIG_LEDS_SUN50I_A100) += leds-sun50i-a100.o obj-$(CONFIG_LEDS_SUNFIRE) += leds-sunfire.o obj-$(CONFIG_LEDS_SYSCON) += leds-syscon.o obj-$(CONFIG_LEDS_TCA6507) += leds-tca6507.o diff --git a/drivers/leds/led-triggers.c b/drivers/leds/led-triggers.c index 6a5e1f4..bd59a14 100644 --- a/drivers/leds/led-triggers.c +++ b/drivers/leds/led-triggers.c @@ -269,19 +269,6 @@ void led_trigger_set_default(struct led_classdev *led_cdev) } EXPORT_SYMBOL_GPL(led_trigger_set_default); -void led_trigger_rename_static(const char *name, struct led_trigger *trig) -{ - /* new name must be on a temporary string to prevent races */ - BUG_ON(name == trig->name); - - down_write(&triggers_list_lock); - /* this assumes that trig->name was originaly allocated to - * non constant storage */ - strcpy((char *)trig->name, name); - up_write(&triggers_list_lock); -} -EXPORT_SYMBOL_GPL(led_trigger_rename_static); - /* LED Trigger Interface */ int led_trigger_register(struct led_trigger *trig) diff --git a/drivers/leds/leds-aw200xx.c b/drivers/leds/leds-aw200xx.c index 14ca236..f584a7f 100644 --- a/drivers/leds/leds-aw200xx.c +++ b/drivers/leds/leds-aw200xx.c @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0 /* - * Awinic AW20036/AW20054/AW20072 LED driver + * Awinic AW20036/AW20054/AW20072/AW20108 LED driver * * Copyright (c) 2023, SberDevices. All Rights Reserved. * @@ -10,6 +10,7 @@ #include #include #include +#include #include #include #include @@ -74,6 +75,10 @@ #define AW200XX_LED2REG(x, columns) \ ((x) + (((x) / (columns)) * (AW200XX_DSIZE_COLUMNS_MAX - (columns)))) +/* DIM current configuration register on page 1 */ +#define AW200XX_REG_DIM_PAGE1(x, columns) \ + AW200XX_REG(AW200XX_PAGE1, AW200XX_LED2REG(x, columns)) + /* * DIM current configuration register (page 4). * The even address for current DIM configuration. @@ -82,6 +87,8 @@ #define AW200XX_REG_DIM(x, columns) \ AW200XX_REG(AW200XX_PAGE4, AW200XX_LED2REG(x, columns) * 2) #define AW200XX_REG_DIM2FADE(x) ((x) + 1) +#define AW200XX_REG_FADE2DIM(fade) \ + DIV_ROUND_UP((fade) * AW200XX_DIM_MAX, AW200XX_FADE_MAX) /* * Duty ratio of display scan (see p.15 of datasheet for formula): @@ -112,6 +119,7 @@ struct aw200xx { struct mutex mutex; u32 num_leds; u32 display_rows; + struct gpio_desc *hwen; struct aw200xx_led leds[] __counted_by(num_leds); }; @@ -153,7 +161,8 @@ static ssize_t dim_store(struct device *dev, struct device_attribute *devattr, if (dim >= 0) { ret = regmap_write(chip->regmap, - AW200XX_REG_DIM(led->num, columns), dim); + AW200XX_REG_DIM_PAGE1(led->num, columns), + dim); if (ret) goto out_unlock; } @@ -188,9 +197,7 @@ static int aw200xx_brightness_set(struct led_classdev *cdev, dim = led->dim; if (dim < 0) - dim = max_t(int, - brightness / (AW200XX_FADE_MAX / AW200XX_DIM_MAX), - 1); + dim = AW200XX_REG_FADE2DIM(brightness); ret = regmap_write(chip->regmap, reg, dim); if (ret) @@ -314,6 +321,9 @@ static int aw200xx_chip_reset(const struct aw200xx *const chip) if (ret) return ret; + /* According to the datasheet software reset takes at least 1ms */ + fsleep(1000); + regcache_mark_dirty(chip->regmap); return regmap_write(chip->regmap, AW200XX_REG_FCD, AW200XX_FCD_CLEAR); } @@ -353,6 +363,50 @@ static int aw200xx_chip_check(const struct aw200xx *const chip) return 0; } +static void aw200xx_enable(const struct aw200xx *const chip) +{ + gpiod_set_value_cansleep(chip->hwen, 1); + + /* + * After HWEN pin set high the chip begins to load the OTP information, + * which takes 200us to complete. About 200us wait time is needed for + * internal oscillator startup and display SRAM initialization. After + * display SRAM initialization, the registers in page1 to page5 can be + * configured via i2c interface. + */ + fsleep(400); +} + +static void aw200xx_disable(const struct aw200xx *const chip) +{ + return gpiod_set_value_cansleep(chip->hwen, 0); +} + +static int aw200xx_probe_get_display_rows(struct device *dev, + struct aw200xx *chip) +{ + struct fwnode_handle *child; + u32 max_source = 0; + + device_for_each_child_node(dev, child) { + u32 source; + int ret; + + ret = fwnode_property_read_u32(child, "reg", &source); + if (ret || source >= chip->cdef->channels) + continue; + + max_source = max(max_source, source); + } + + if (max_source == 0) + return -EINVAL; + + chip->display_rows = max_source / chip->cdef->display_size_columns + 1; + + return 0; +} + static int aw200xx_probe_fw(struct device *dev, struct aw200xx *chip) { struct fwnode_handle *child; @@ -360,18 +414,10 @@ static int aw200xx_probe_fw(struct device *dev, struct aw200xx *chip) int ret; int i; - ret = device_property_read_u32(dev, "awinic,display-rows", - &chip->display_rows); + ret = aw200xx_probe_get_display_rows(dev, chip); if (ret) return dev_err_probe(dev, ret, - "Failed to read 'display-rows' property\n"); - - if (!chip->display_rows || - chip->display_rows > chip->cdef->display_size_rows_max) { - return dev_err_probe(dev, -EINVAL, - "Invalid leds display size %u\n", - chip->display_rows); - } + "No valid led definitions found\n"); current_max = aw200xx_imax_from_global(chip, AW200XX_IMAX_MAX_uA); current_min = aw200xx_imax_from_global(chip, AW200XX_IMAX_MIN_uA); @@ -416,6 +462,7 @@ static int aw200xx_probe_fw(struct device *dev, struct aw200xx *chip) led->num = source; led->chip = chip; led->cdev.brightness_set_blocking = aw200xx_brightness_set; + led->cdev.max_brightness = AW200XX_FADE_MAX; led->cdev.groups = dim_groups; init_data.fwnode = child; @@ -480,6 +527,7 @@ static const struct regmap_config aw200xx_regmap_config = { .rd_table = &aw200xx_readable_table, .wr_table = &aw200xx_writeable_table, .cache_type = REGCACHE_MAPLE, + .disable_locking = true, }; static int aw200xx_probe(struct i2c_client *client) @@ -512,6 +560,14 @@ static int aw200xx_probe(struct i2c_client *client) if (IS_ERR(chip->regmap)) return PTR_ERR(chip->regmap); + chip->hwen = devm_gpiod_get_optional(&client->dev, "enable", + GPIOD_OUT_HIGH); + if (IS_ERR(chip->hwen)) + return dev_err_probe(&client->dev, PTR_ERR(chip->hwen), + "Cannot get enable GPIO"); + + aw200xx_enable(chip); + ret = aw200xx_chip_check(chip); if (ret) return ret; @@ -532,6 +588,9 @@ static int aw200xx_probe(struct i2c_client *client) ret = aw200xx_chip_init(chip); out_unlock: + if (ret) + aw200xx_disable(chip); + mutex_unlock(&chip->mutex); return ret; } @@ -541,6 +600,7 @@ static void aw200xx_remove(struct i2c_client *client) struct aw200xx *chip = i2c_get_clientdata(client); aw200xx_chip_reset(chip); + aw200xx_disable(chip); mutex_destroy(&chip->mutex); } @@ -562,10 +622,17 @@ static const struct aw200xx_chipdef aw20072_cdef = { .display_size_columns = 12, }; +static const struct aw200xx_chipdef aw20108_cdef = { + .channels = 108, + .display_size_rows_max = 9, + .display_size_columns = 12, +}; + static const struct i2c_device_id aw200xx_id[] = { { "aw20036" }, { "aw20054" }, { "aw20072" }, + { "aw20108" }, {} }; MODULE_DEVICE_TABLE(i2c, aw200xx_id); @@ -574,6 +641,7 @@ static const struct of_device_id aw200xx_match_table[] = { { .compatible = "awinic,aw20036", .data = &aw20036_cdef, }, { .compatible = "awinic,aw20054", .data = &aw20054_cdef, }, { .compatible = "awinic,aw20072", .data = &aw20072_cdef, }, + { .compatible = "awinic,aw20108", .data = &aw20108_cdef, }, {} }; MODULE_DEVICE_TABLE(of, aw200xx_match_table); diff --git a/drivers/leds/leds-gpio.c b/drivers/leds/leds-gpio.c index 710c319..83fcd7b 100644 --- a/drivers/leds/leds-gpio.c +++ b/drivers/leds/leds-gpio.c @@ -172,6 +172,8 @@ static struct gpio_leds_priv *gpio_leds_create(struct device *dev) led.gpiod = devm_fwnode_gpiod_get(dev, child, NULL, GPIOD_ASIS, NULL); if (IS_ERR(led.gpiod)) { + dev_err_probe(dev, PTR_ERR(led.gpiod), "Failed to get GPIO '%pfw'\n", + child); fwnode_handle_put(child); return ERR_CAST(led.gpiod); } diff --git a/drivers/leds/leds-max5970.c b/drivers/leds/leds-max5970.c new file mode 100644 index 0000000..56a5843 --- /dev/null +++ b/drivers/leds/leds-max5970.c @@ -0,0 +1,111 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Device driver for leds in MAX5970 and MAX5978 IC + * + * Copyright (c) 2022 9elements GmbH + * + * Author: Patrick Rudolph + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define ldev_to_maxled(c) container_of(c, struct max5970_led, cdev) + +struct max5970_led { + struct device *dev; + struct regmap *regmap; + struct led_classdev cdev; + unsigned int index; +}; + +static int max5970_led_set_brightness(struct led_classdev *cdev, + enum led_brightness brightness) +{ + struct max5970_led *ddata = ldev_to_maxled(cdev); + int ret, val; + + /* Set/clear corresponding bit for given led index */ + val = !brightness ? BIT(ddata->index) : 0; + + ret = regmap_update_bits(ddata->regmap, MAX5970_REG_LED_FLASH, BIT(ddata->index), val); + if (ret < 0) + dev_err(cdev->dev, "failed to set brightness %d", ret); + + return ret; +} + +static int max5970_led_probe(struct platform_device *pdev) +{ + struct fwnode_handle *led_node, *child; + struct device *dev = &pdev->dev; + struct regmap *regmap; + struct max5970_led *ddata; + int ret = -ENODEV; + + regmap = dev_get_regmap(dev->parent, NULL); + if (!regmap) + return -ENODEV; + + led_node = device_get_named_child_node(dev->parent, "leds"); + if (!led_node) + return -ENODEV; + + fwnode_for_each_available_child_node(led_node, child) { + u32 reg; + + if (fwnode_property_read_u32(child, "reg", ®)) + continue; + + if (reg >= MAX5970_NUM_LEDS) { + dev_err_probe(dev, -EINVAL, "invalid LED (%u >= %d)\n", reg, MAX5970_NUM_LEDS); + continue; + } + + ddata = devm_kzalloc(dev, sizeof(*ddata), GFP_KERNEL); + if (!ddata) { + fwnode_handle_put(child); + return -ENOMEM; + } + + ddata->index = reg; + ddata->regmap = regmap; + ddata->dev = dev; + + if (fwnode_property_read_string(child, "label", &ddata->cdev.name)) + ddata->cdev.name = fwnode_get_name(child); + + ddata->cdev.max_brightness = 1; + ddata->cdev.brightness_set_blocking = max5970_led_set_brightness; + ddata->cdev.default_trigger = "none"; + + ret = devm_led_classdev_register(dev, &ddata->cdev); + if (ret < 0) { + fwnode_handle_put(child); + return dev_err_probe(dev, ret, "Failed to initialize LED %u\n", reg); + } + } + + return ret; +} + +static struct platform_driver max5970_led_driver = { + .driver = { + .name = "max5970-led", + }, + .probe = max5970_led_probe, +}; +module_platform_driver(max5970_led_driver); + +MODULE_AUTHOR("Patrick Rudolph "); +MODULE_AUTHOR("Naresh Solanki "); +MODULE_DESCRIPTION("MAX5970_hot-swap controller LED driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/leds/leds-sun50i-a100.c b/drivers/leds/leds-sun50i-a100.c new file mode 100644 index 0000000..62d21c3 --- /dev/null +++ b/drivers/leds/leds-sun50i-a100.c @@ -0,0 +1,584 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021-2023 Samuel Holland + * + * Partly based on drivers/leds/leds-turris-omnia.c, which is: + * Copyright (c) 2020 by Marek Behún + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define LEDC_CTRL_REG 0x0000 +#define LEDC_CTRL_REG_DATA_LENGTH GENMASK(28, 16) +#define LEDC_CTRL_REG_RGB_MODE GENMASK(8, 6) +#define LEDC_CTRL_REG_LEDC_EN BIT(0) +#define LEDC_T01_TIMING_CTRL_REG 0x0004 +#define LEDC_T01_TIMING_CTRL_REG_T1H GENMASK(26, 21) +#define LEDC_T01_TIMING_CTRL_REG_T1L GENMASK(20, 16) +#define LEDC_T01_TIMING_CTRL_REG_T0H GENMASK(10, 6) +#define LEDC_T01_TIMING_CTRL_REG_T0L GENMASK(5, 0) +#define LEDC_RESET_TIMING_CTRL_REG 0x000c +#define LEDC_RESET_TIMING_CTRL_REG_TR GENMASK(28, 16) +#define LEDC_RESET_TIMING_CTRL_REG_LED_NUM GENMASK(9, 0) +#define LEDC_DATA_REG 0x0014 +#define LEDC_DMA_CTRL_REG 0x0018 +#define LEDC_DMA_CTRL_REG_DMA_EN BIT(5) +#define LEDC_DMA_CTRL_REG_FIFO_TRIG_LEVEL GENMASK(4, 0) +#define LEDC_INT_CTRL_REG 0x001c +#define LEDC_INT_CTRL_REG_GLOBAL_INT_EN BIT(5) +#define LEDC_INT_CTRL_REG_FIFO_CPUREQ_INT_EN BIT(1) +#define LEDC_INT_CTRL_REG_TRANS_FINISH_INT_EN BIT(0) +#define LEDC_INT_STS_REG 0x0020 +#define LEDC_INT_STS_REG_FIFO_WLW GENMASK(15, 10) +#define LEDC_INT_STS_REG_FIFO_CPUREQ_INT BIT(1) +#define LEDC_INT_STS_REG_TRANS_FINISH_INT BIT(0) + +#define LEDC_FIFO_DEPTH 32U +#define LEDC_MAX_LEDS 1024 +#define LEDC_CHANNELS_PER_LED 3 /* RGB */ + +#define LEDS_TO_BYTES(n) ((n) * sizeof(u32)) + +struct sun50i_a100_ledc_led { + struct led_classdev_mc mc_cdev; + struct mc_subled subled_info[LEDC_CHANNELS_PER_LED]; + u32 addr; +}; + +#define to_ledc_led(mc) container_of(mc, struct sun50i_a100_ledc_led, mc_cdev) + +struct sun50i_a100_ledc_timing { + u32 t0h_ns; + u32 t0l_ns; + u32 t1h_ns; + u32 t1l_ns; + u32 treset_ns; +}; + +struct sun50i_a100_ledc { + struct device *dev; + void __iomem *base; + struct clk *bus_clk; + struct clk *mod_clk; + struct reset_control *reset; + + u32 *buffer; + struct dma_chan *dma_chan; + dma_addr_t dma_handle; + unsigned int pio_length; + unsigned int pio_offset; + + spinlock_t lock; + unsigned int next_length; + bool xfer_active; + + u32 format; + struct sun50i_a100_ledc_timing timing; + + u32 max_addr; + u32 num_leds; + struct sun50i_a100_ledc_led leds[] __counted_by(num_leds); +}; + +static int sun50i_a100_ledc_dma_xfer(struct sun50i_a100_ledc *priv, unsigned int length) +{ + struct dma_async_tx_descriptor *desc; + dma_cookie_t cookie; + + desc = dmaengine_prep_slave_single(priv->dma_chan, priv->dma_handle, + LEDS_TO_BYTES(length), DMA_MEM_TO_DEV, 0); + if (!desc) + return -ENOMEM; + + cookie = dmaengine_submit(desc); + if (dma_submit_error(cookie)) + return -EIO; + + dma_async_issue_pending(priv->dma_chan); + + return 0; +} + +static void sun50i_a100_ledc_pio_xfer(struct sun50i_a100_ledc *priv, unsigned int fifo_used) +{ + unsigned int burst, length, offset; + u32 control; + + length = priv->pio_length; + offset = priv->pio_offset; + burst = min(length, LEDC_FIFO_DEPTH - fifo_used); + + iowrite32_rep(priv->base + LEDC_DATA_REG, priv->buffer + offset, burst); + + if (burst < length) { + priv->pio_length = length - burst; + priv->pio_offset = offset + burst; + + if (!offset) { + control = readl(priv->base + LEDC_INT_CTRL_REG); + control |= LEDC_INT_CTRL_REG_FIFO_CPUREQ_INT_EN; + writel(control, priv->base + LEDC_INT_CTRL_REG); + } + } else { + /* Disable the request IRQ once all data is written. */ + control = readl(priv->base + LEDC_INT_CTRL_REG); + control &= ~LEDC_INT_CTRL_REG_FIFO_CPUREQ_INT_EN; + writel(control, priv->base + LEDC_INT_CTRL_REG); + } +} + +static void sun50i_a100_ledc_start_xfer(struct sun50i_a100_ledc *priv, unsigned int length) +{ + bool use_dma = false; + u32 control; + + if (priv->dma_chan && length > LEDC_FIFO_DEPTH) { + int ret; + + ret = sun50i_a100_ledc_dma_xfer(priv, length); + if (ret) + dev_warn(priv->dev, "Failed to set up DMA (%d), using PIO\n", ret); + else + use_dma = true; + } + + /* The DMA trigger level must be at least the burst length. */ + control = FIELD_PREP(LEDC_DMA_CTRL_REG_DMA_EN, use_dma) | + FIELD_PREP_CONST(LEDC_DMA_CTRL_REG_FIFO_TRIG_LEVEL, LEDC_FIFO_DEPTH / 2); + writel(control, priv->base + LEDC_DMA_CTRL_REG); + + control = readl(priv->base + LEDC_CTRL_REG); + control &= ~LEDC_CTRL_REG_DATA_LENGTH; + control |= FIELD_PREP(LEDC_CTRL_REG_DATA_LENGTH, length) | LEDC_CTRL_REG_LEDC_EN; + writel(control, priv->base + LEDC_CTRL_REG); + + if (!use_dma) { + /* The FIFO is empty when starting a new transfer. */ + unsigned int fifo_used = 0; + + priv->pio_length = length; + priv->pio_offset = 0; + + sun50i_a100_ledc_pio_xfer(priv, fifo_used); + } +} + +static irqreturn_t sun50i_a100_ledc_irq(int irq, void *data) +{ + struct sun50i_a100_ledc *priv = data; + u32 status; + + status = readl(priv->base + LEDC_INT_STS_REG); + + if (status & LEDC_INT_STS_REG_TRANS_FINISH_INT) { + unsigned int next_length; + + spin_lock(&priv->lock); + + /* If another transfer is queued, dequeue and start it. */ + next_length = priv->next_length; + if (next_length) + priv->next_length = 0; + else + priv->xfer_active = false; + + spin_unlock(&priv->lock); + + if (next_length) + sun50i_a100_ledc_start_xfer(priv, next_length); + } else if (status & LEDC_INT_STS_REG_FIFO_CPUREQ_INT) { + /* Continue the current transfer. */ + sun50i_a100_ledc_pio_xfer(priv, FIELD_GET(LEDC_INT_STS_REG_FIFO_WLW, status)); + } + + /* Clear the W1C status bits. */ + writel(status, priv->base + LEDC_INT_STS_REG); + + return IRQ_HANDLED; +} + +static void sun50i_a100_ledc_brightness_set(struct led_classdev *cdev, + enum led_brightness brightness) +{ + struct sun50i_a100_ledc *priv = dev_get_drvdata(cdev->dev->parent); + struct led_classdev_mc *mc_cdev = lcdev_to_mccdev(cdev); + struct sun50i_a100_ledc_led *led = to_ledc_led(mc_cdev); + unsigned int next_length; + unsigned long flags; + bool xfer_active; + + led_mc_calc_color_components(mc_cdev, brightness); + + priv->buffer[led->addr] = led->subled_info[0].brightness << 16 | + led->subled_info[1].brightness << 8 | + led->subled_info[2].brightness; + + spin_lock_irqsave(&priv->lock, flags); + + /* Start, enqueue, or extend an enqueued transfer, as appropriate. */ + next_length = max(priv->next_length, led->addr + 1); + xfer_active = priv->xfer_active; + if (xfer_active) + priv->next_length = next_length; + else + priv->xfer_active = true; + + spin_unlock_irqrestore(&priv->lock, flags); + + if (!xfer_active) + sun50i_a100_ledc_start_xfer(priv, next_length); +} + +static const char *const sun50i_a100_ledc_formats[] = { + "rgb", "rbg", "grb", "gbr", "brg", "bgr", +}; + +static int sun50i_a100_ledc_parse_format(struct device *dev, + struct sun50i_a100_ledc *priv) +{ + const char *format = "grb"; + u32 i; + + device_property_read_string(dev, "allwinner,pixel-format", &format); + + for (i = 0; i < ARRAY_SIZE(sun50i_a100_ledc_formats); i++) { + if (!strcmp(format, sun50i_a100_ledc_formats[i])) { + priv->format = i; + return 0; + } + } + + return dev_err_probe(dev, -EINVAL, "Bad pixel format '%s'\n", format); +} + +static void sun50i_a100_ledc_set_format(struct sun50i_a100_ledc *priv) +{ + u32 control; + + control = readl(priv->base + LEDC_CTRL_REG); + control &= ~LEDC_CTRL_REG_RGB_MODE; + control |= FIELD_PREP(LEDC_CTRL_REG_RGB_MODE, priv->format); + writel(control, priv->base + LEDC_CTRL_REG); +} + +static const struct sun50i_a100_ledc_timing sun50i_a100_ledc_default_timing = { + .t0h_ns = 336, + .t0l_ns = 840, + .t1h_ns = 882, + .t1l_ns = 294, + .treset_ns = 300000, +}; + +static int sun50i_a100_ledc_parse_timing(struct device *dev, + struct sun50i_a100_ledc *priv) +{ + struct sun50i_a100_ledc_timing *timing = &priv->timing; + + *timing = sun50i_a100_ledc_default_timing; + + device_property_read_u32(dev, "allwinner,t0h-ns", &timing->t0h_ns); + device_property_read_u32(dev, "allwinner,t0l-ns", &timing->t0l_ns); + device_property_read_u32(dev, "allwinner,t1h-ns", &timing->t1h_ns); + device_property_read_u32(dev, "allwinner,t1l-ns", &timing->t1l_ns); + device_property_read_u32(dev, "allwinner,treset-ns", &timing->treset_ns); + + return 0; +} + +static void sun50i_a100_ledc_set_timing(struct sun50i_a100_ledc *priv) +{ + const struct sun50i_a100_ledc_timing *timing = &priv->timing; + unsigned long mod_freq = clk_get_rate(priv->mod_clk); + u32 cycle_ns; + u32 control; + + if (!mod_freq) + return; + + cycle_ns = NSEC_PER_SEC / mod_freq; + control = FIELD_PREP(LEDC_T01_TIMING_CTRL_REG_T1H, timing->t1h_ns / cycle_ns) | + FIELD_PREP(LEDC_T01_TIMING_CTRL_REG_T1L, timing->t1l_ns / cycle_ns) | + FIELD_PREP(LEDC_T01_TIMING_CTRL_REG_T0H, timing->t0h_ns / cycle_ns) | + FIELD_PREP(LEDC_T01_TIMING_CTRL_REG_T0L, timing->t0l_ns / cycle_ns); + writel(control, priv->base + LEDC_T01_TIMING_CTRL_REG); + + control = FIELD_PREP(LEDC_RESET_TIMING_CTRL_REG_TR, timing->treset_ns / cycle_ns) | + FIELD_PREP(LEDC_RESET_TIMING_CTRL_REG_LED_NUM, priv->max_addr); + writel(control, priv->base + LEDC_RESET_TIMING_CTRL_REG); +} + +static int sun50i_a100_ledc_resume(struct device *dev) +{ + struct sun50i_a100_ledc *priv = dev_get_drvdata(dev); + int ret; + + ret = reset_control_deassert(priv->reset); + if (ret) + return ret; + + ret = clk_prepare_enable(priv->bus_clk); + if (ret) + goto err_assert_reset; + + ret = clk_prepare_enable(priv->mod_clk); + if (ret) + goto err_disable_bus_clk; + + sun50i_a100_ledc_set_format(priv); + sun50i_a100_ledc_set_timing(priv); + + writel(LEDC_INT_CTRL_REG_GLOBAL_INT_EN | LEDC_INT_CTRL_REG_TRANS_FINISH_INT_EN, + priv->base + LEDC_INT_CTRL_REG); + + return 0; + +err_disable_bus_clk: + clk_disable_unprepare(priv->bus_clk); +err_assert_reset: + reset_control_assert(priv->reset); + + return ret; +} + +static int sun50i_a100_ledc_suspend(struct device *dev) +{ + struct sun50i_a100_ledc *priv = dev_get_drvdata(dev); + + /* Wait for all transfers to complete. */ + for (;;) { + unsigned long flags; + bool xfer_active; + + spin_lock_irqsave(&priv->lock, flags); + xfer_active = priv->xfer_active; + spin_unlock_irqrestore(&priv->lock, flags); + if (!xfer_active) + break; + + msleep(1); + } + + clk_disable_unprepare(priv->mod_clk); + clk_disable_unprepare(priv->bus_clk); + reset_control_assert(priv->reset); + + return 0; +} + +static void sun50i_a100_ledc_dma_cleanup(void *data) +{ + struct sun50i_a100_ledc *priv = data; + + dma_release_channel(priv->dma_chan); +} + +static int sun50i_a100_ledc_probe(struct platform_device *pdev) +{ + struct dma_slave_config dma_cfg = {}; + struct led_init_data init_data = {}; + struct sun50i_a100_ledc_led *led; + struct device *dev = &pdev->dev; + struct sun50i_a100_ledc *priv; + struct fwnode_handle *child; + struct resource *mem; + u32 max_addr = 0; + u32 num_leds = 0; + int irq, ret; + + /* + * The maximum LED address must be known in sun50i_a100_ledc_resume() before + * class device registration, so parse and validate the subnodes up front. + */ + device_for_each_child_node(dev, child) { + u32 addr, color; + + ret = fwnode_property_read_u32(child, "reg", &addr); + if (ret || addr >= LEDC_MAX_LEDS) { + fwnode_handle_put(child); + return dev_err_probe(dev, -EINVAL, "'reg' must be between 0 and %d\n", + LEDC_MAX_LEDS - 1); + } + + ret = fwnode_property_read_u32(child, "color", &color); + if (ret || color != LED_COLOR_ID_RGB) { + fwnode_handle_put(child); + return dev_err_probe(dev, -EINVAL, "'color' must be LED_COLOR_ID_RGB\n"); + } + + max_addr = max(max_addr, addr); + num_leds++; + } + + if (!num_leds) + return -ENODEV; + + priv = devm_kzalloc(dev, struct_size(priv, leds, num_leds), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + priv->dev = dev; + priv->max_addr = max_addr; + priv->num_leds = num_leds; + spin_lock_init(&priv->lock); + dev_set_drvdata(dev, priv); + + ret = sun50i_a100_ledc_parse_format(dev, priv); + if (ret) + return ret; + + ret = sun50i_a100_ledc_parse_timing(dev, priv); + if (ret) + return ret; + + priv->base = devm_platform_get_and_ioremap_resource(pdev, 0, &mem); + if (IS_ERR(priv->base)) + return PTR_ERR(priv->base); + + priv->bus_clk = devm_clk_get(dev, "bus"); + if (IS_ERR(priv->bus_clk)) + return PTR_ERR(priv->bus_clk); + + priv->mod_clk = devm_clk_get(dev, "mod"); + if (IS_ERR(priv->mod_clk)) + return PTR_ERR(priv->mod_clk); + + priv->reset = devm_reset_control_get_exclusive(dev, NULL); + if (IS_ERR(priv->reset)) + return PTR_ERR(priv->reset); + + priv->dma_chan = dma_request_chan(dev, "tx"); + if (IS_ERR(priv->dma_chan)) { + if (PTR_ERR(priv->dma_chan) != -ENODEV) + return PTR_ERR(priv->dma_chan); + + priv->dma_chan = NULL; + + priv->buffer = devm_kzalloc(dev, LEDS_TO_BYTES(LEDC_MAX_LEDS), GFP_KERNEL); + if (!priv->buffer) + return -ENOMEM; + } else { + ret = devm_add_action_or_reset(dev, sun50i_a100_ledc_dma_cleanup, priv); + if (ret) + return ret; + + dma_cfg.dst_addr = mem->start + LEDC_DATA_REG; + dma_cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + dma_cfg.dst_maxburst = LEDC_FIFO_DEPTH / 2; + + ret = dmaengine_slave_config(priv->dma_chan, &dma_cfg); + if (ret) + return ret; + + priv->buffer = dmam_alloc_attrs(dmaengine_get_dma_device(priv->dma_chan), + LEDS_TO_BYTES(LEDC_MAX_LEDS), &priv->dma_handle, + GFP_KERNEL, DMA_ATTR_WRITE_COMBINE); + if (!priv->buffer) + return -ENOMEM; + } + + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return irq; + + ret = devm_request_irq(dev, irq, sun50i_a100_ledc_irq, 0, dev_name(dev), priv); + if (ret) + return ret; + + ret = sun50i_a100_ledc_resume(dev); + if (ret) + return ret; + + led = priv->leds; + device_for_each_child_node(dev, child) { + struct led_classdev *cdev; + + /* The node was already validated above. */ + fwnode_property_read_u32(child, "reg", &led->addr); + + led->subled_info[0].color_index = LED_COLOR_ID_RED; + led->subled_info[0].channel = 0; + led->subled_info[1].color_index = LED_COLOR_ID_GREEN; + led->subled_info[1].channel = 1; + led->subled_info[2].color_index = LED_COLOR_ID_BLUE; + led->subled_info[2].channel = 2; + + led->mc_cdev.num_colors = ARRAY_SIZE(led->subled_info); + led->mc_cdev.subled_info = led->subled_info; + + cdev = &led->mc_cdev.led_cdev; + cdev->max_brightness = U8_MAX; + cdev->brightness_set = sun50i_a100_ledc_brightness_set; + + init_data.fwnode = child; + + ret = led_classdev_multicolor_register_ext(dev, &led->mc_cdev, &init_data); + if (ret) { + dev_err_probe(dev, ret, "Failed to register multicolor LED %u", led->addr); + goto err_put_child; + } + + led++; + } + + dev_info(dev, "Registered %u LEDs\n", num_leds); + + return 0; + +err_put_child: + fwnode_handle_put(child); + while (led-- > priv->leds) + led_classdev_multicolor_unregister(&led->mc_cdev); + sun50i_a100_ledc_suspend(&pdev->dev); + + return ret; +} + +static void sun50i_a100_ledc_remove(struct platform_device *pdev) +{ + struct sun50i_a100_ledc *priv = platform_get_drvdata(pdev); + + for (u32 i = 0; i < priv->num_leds; i++) + led_classdev_multicolor_unregister(&priv->leds[i].mc_cdev); + sun50i_a100_ledc_suspend(&pdev->dev); +} + +static const struct of_device_id sun50i_a100_ledc_of_match[] = { + { .compatible = "allwinner,sun50i-a100-ledc" }, + {} +}; +MODULE_DEVICE_TABLE(of, sun50i_a100_ledc_of_match); + +static DEFINE_SIMPLE_DEV_PM_OPS(sun50i_a100_ledc_pm, + sun50i_a100_ledc_suspend, + sun50i_a100_ledc_resume); + +static struct platform_driver sun50i_a100_ledc_driver = { + .probe = sun50i_a100_ledc_probe, + .remove_new = sun50i_a100_ledc_remove, + .shutdown = sun50i_a100_ledc_remove, + .driver = { + .name = "sun50i-a100-ledc", + .of_match_table = sun50i_a100_ledc_of_match, + .pm = pm_ptr(&sun50i_a100_ledc_pm), + }, +}; +module_platform_driver(sun50i_a100_ledc_driver); + +MODULE_AUTHOR("Samuel Holland "); +MODULE_DESCRIPTION("Allwinner A100 LED controller driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/leds/leds-syscon.c b/drivers/leds/leds-syscon.c index 360a376..d633ad5 100644 --- a/drivers/leds/leds-syscon.c +++ b/drivers/leds/leds-syscon.c @@ -81,7 +81,8 @@ static int syscon_led_probe(struct platform_device *pdev) sled->map = map; - if (of_property_read_u32(np, "offset", &sled->offset)) + if (of_property_read_u32(np, "reg", &sled->offset) && + of_property_read_u32(np, "offset", &sled->offset)) return -EINVAL; if (of_property_read_u32(np, "mask", &sled->mask)) return -EINVAL; diff --git a/drivers/leds/leds-tca6507.c b/drivers/leds/leds-tca6507.c index e190746..4f22f42 100644 --- a/drivers/leds/leds-tca6507.c +++ b/drivers/leds/leds-tca6507.c @@ -638,19 +638,13 @@ static int tca6507_probe_gpios(struct device *dev, tca->gpio.direction_output = tca6507_gpio_direction_output; tca->gpio.set = tca6507_gpio_set_value; tca->gpio.parent = dev; - err = gpiochip_add_data(&tca->gpio, tca); + err = devm_gpiochip_add_data(dev, &tca->gpio, tca); if (err) { tca->gpio.ngpio = 0; return err; } return 0; } - -static void tca6507_remove_gpio(struct tca6507_chip *tca) -{ - if (tca->gpio.ngpio) - gpiochip_remove(&tca->gpio); -} #else /* CONFIG_GPIOLIB */ static int tca6507_probe_gpios(struct device *dev, struct tca6507_chip *tca, @@ -658,9 +652,6 @@ static int tca6507_probe_gpios(struct device *dev, { return 0; } -static void tca6507_remove_gpio(struct tca6507_chip *tca) -{ -} #endif /* CONFIG_GPIOLIB */ static struct tca6507_platform_data * @@ -762,38 +753,25 @@ static int tca6507_probe(struct i2c_client *client) l->led_cdev.brightness_set = tca6507_brightness_set; l->led_cdev.blink_set = tca6507_blink_set; l->bank = -1; - err = led_classdev_register(dev, &l->led_cdev); + err = devm_led_classdev_register(dev, &l->led_cdev); if (err < 0) - goto exit; + return err; } } err = tca6507_probe_gpios(dev, tca, pdata); if (err) - goto exit; + return err; /* set all registers to known state - zero */ tca->reg_set = 0x7f; schedule_work(&tca->work); return 0; -exit: - while (i--) { - if (tca->leds[i].led_cdev.name) - led_classdev_unregister(&tca->leds[i].led_cdev); - } - return err; } static void tca6507_remove(struct i2c_client *client) { - int i; struct tca6507_chip *tca = i2c_get_clientdata(client); - struct tca6507_led *tca_leds = tca->leds; - for (i = 0; i < NUM_LEDS; i++) { - if (tca_leds[i].led_cdev.name) - led_classdev_unregister(&tca_leds[i].led_cdev); - } - tca6507_remove_gpio(tca); cancel_work_sync(&tca->work); } diff --git a/drivers/leds/rgb/Kconfig b/drivers/leds/rgb/Kconfig index a6a21f5..e66bd21 100644 --- a/drivers/leds/rgb/Kconfig +++ b/drivers/leds/rgb/Kconfig @@ -4,7 +4,7 @@ if LEDS_CLASS_MULTICOLOR config LEDS_GROUP_MULTICOLOR tristate "LEDs group multi-color support" - depends on OF || COMPILE_TEST + depends on OF help This option enables support for monochrome LEDs that are grouped into multicolor LEDs which is useful in the case where LEDs of diff --git a/drivers/leds/rgb/leds-qcom-lpg.c b/drivers/leds/rgb/leds-qcom-lpg.c index 68d82a6..156b73d 100644 --- a/drivers/leds/rgb/leds-qcom-lpg.c +++ b/drivers/leds/rgb/leds-qcom-lpg.c @@ -552,9 +552,9 @@ static int lpg_parse_dtest(struct lpg *lpg) ret = count; goto err_malformed; } else if (count != lpg->data->num_channels * 2) { - dev_err(lpg->dev, "qcom,dtest needs to be %d items\n", - lpg->data->num_channels * 2); - return -EINVAL; + return dev_err_probe(lpg->dev, -EINVAL, + "qcom,dtest needs to be %d items\n", + lpg->data->num_channels * 2); } for (i = 0; i < lpg->data->num_channels; i++) { @@ -574,8 +574,7 @@ static int lpg_parse_dtest(struct lpg *lpg) return 0; err_malformed: - dev_err(lpg->dev, "malformed qcom,dtest\n"); - return ret; + return dev_err_probe(lpg->dev, ret, "malformed qcom,dtest\n"); } static void lpg_apply_dtest(struct lpg_channel *chan) @@ -977,9 +976,14 @@ static int lpg_pattern_mc_clear(struct led_classdev *cdev) return lpg_pattern_clear(led); } +static inline struct lpg *lpg_pwm_from_chip(struct pwm_chip *chip) +{ + return container_of(chip, struct lpg, pwm); +} + static int lpg_pwm_request(struct pwm_chip *chip, struct pwm_device *pwm) { - struct lpg *lpg = container_of(chip, struct lpg, pwm); + struct lpg *lpg = lpg_pwm_from_chip(chip); struct lpg_channel *chan = &lpg->channels[pwm->hwpwm]; return chan->in_use ? -EBUSY : 0; @@ -995,7 +999,7 @@ static int lpg_pwm_request(struct pwm_chip *chip, struct pwm_device *pwm) static int lpg_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm, const struct pwm_state *state) { - struct lpg *lpg = container_of(chip, struct lpg, pwm); + struct lpg *lpg = lpg_pwm_from_chip(chip); struct lpg_channel *chan = &lpg->channels[pwm->hwpwm]; int ret = 0; @@ -1026,7 +1030,7 @@ out_unlock: static int lpg_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm, struct pwm_state *state) { - struct lpg *lpg = container_of(chip, struct lpg, pwm); + struct lpg *lpg = lpg_pwm_from_chip(chip); struct lpg_channel *chan = &lpg->channels[pwm->hwpwm]; unsigned int resolution; unsigned int pre_div; @@ -1095,9 +1099,9 @@ static int lpg_add_pwm(struct lpg *lpg) lpg->pwm.npwm = lpg->num_channels; lpg->pwm.ops = &lpg_pwm_ops; - ret = pwmchip_add(&lpg->pwm); + ret = devm_pwmchip_add(lpg->dev, &lpg->pwm); if (ret) - dev_err(lpg->dev, "failed to add PWM chip: ret %d\n", ret); + dev_err_probe(lpg->dev, ret, "failed to add PWM chip\n"); return ret; } @@ -1111,19 +1115,16 @@ static int lpg_parse_channel(struct lpg *lpg, struct device_node *np, int ret; ret = of_property_read_u32(np, "reg", ®); - if (ret || !reg || reg > lpg->num_channels) { - dev_err(lpg->dev, "invalid \"reg\" of %pOFn\n", np); - return -EINVAL; - } + if (ret || !reg || reg > lpg->num_channels) + return dev_err_probe(lpg->dev, -EINVAL, "invalid \"reg\" of %pOFn\n", np); chan = &lpg->channels[reg - 1]; chan->in_use = true; ret = of_property_read_u32(np, "color", &color); - if (ret < 0 && ret != -EINVAL) { - dev_err(lpg->dev, "failed to parse \"color\" of %pOF\n", np); - return ret; - } + if (ret < 0 && ret != -EINVAL) + return dev_err_probe(lpg->dev, ret, + "failed to parse \"color\" of %pOF\n", np); chan->color = color; @@ -1146,10 +1147,9 @@ static int lpg_add_led(struct lpg *lpg, struct device_node *np) int i; ret = of_property_read_u32(np, "color", &color); - if (ret < 0 && ret != -EINVAL) { - dev_err(lpg->dev, "failed to parse \"color\" of %pOF\n", np); - return ret; - } + if (ret < 0 && ret != -EINVAL) + return dev_err_probe(lpg->dev, ret, + "failed to parse \"color\" of %pOF\n", np); if (color == LED_COLOR_ID_RGB) num_channels = of_get_available_child_count(np); @@ -1226,7 +1226,7 @@ static int lpg_add_led(struct lpg *lpg, struct device_node *np) else ret = devm_led_classdev_register_ext(lpg->dev, &led->cdev, &init_data); if (ret) - dev_err(lpg->dev, "unable to register %s\n", cdev->name); + dev_err_probe(lpg->dev, ret, "unable to register %s\n", cdev->name); return ret; } @@ -1272,10 +1272,9 @@ static int lpg_init_triled(struct lpg *lpg) if (lpg->triled_has_src_sel) { ret = of_property_read_u32(np, "qcom,power-source", &lpg->triled_src); - if (ret || lpg->triled_src == 2 || lpg->triled_src > 3) { - dev_err(lpg->dev, "invalid power source\n"); - return -EINVAL; - } + if (ret || lpg->triled_src == 2 || lpg->triled_src > 3) + return dev_err_probe(lpg->dev, -EINVAL, + "invalid power source\n"); } /* Disable automatic trickle charge LED */ @@ -1324,8 +1323,6 @@ static int lpg_probe(struct platform_device *pdev) if (!lpg->data) return -EINVAL; - platform_set_drvdata(pdev, lpg); - lpg->dev = &pdev->dev; mutex_init(&lpg->lock); @@ -1363,13 +1360,6 @@ static int lpg_probe(struct platform_device *pdev) return lpg_add_pwm(lpg); } -static void lpg_remove(struct platform_device *pdev) -{ - struct lpg *lpg = platform_get_drvdata(pdev); - - pwmchip_remove(&lpg->pwm); -} - static const struct lpg_data pm8916_pwm_data = { .num_channels = 1, .channels = (const struct lpg_channel_data[]) { @@ -1529,7 +1519,6 @@ MODULE_DEVICE_TABLE(of, lpg_of_table); static struct platform_driver lpg_driver = { .probe = lpg_probe, - .remove_new = lpg_remove, .driver = { .name = "qcom-spmi-lpg", .of_match_table = lpg_of_table, diff --git a/drivers/leds/trigger/ledtrig-gpio.c b/drivers/leds/trigger/ledtrig-gpio.c index 9b7fe5d..7f6a235 100644 --- a/drivers/leds/trigger/ledtrig-gpio.c +++ b/drivers/leds/trigger/ledtrig-gpio.c @@ -41,33 +41,30 @@ static irqreturn_t gpio_trig_irq(int irq, void *_led) return IRQ_HANDLED; } -static ssize_t gpio_trig_brightness_show(struct device *dev, +static ssize_t desired_brightness_show(struct device *dev, struct device_attribute *attr, char *buf) { struct gpio_trig_data *gpio_data = led_trigger_get_drvdata(dev); - return sprintf(buf, "%u\n", gpio_data->desired_brightness); + return sysfs_emit(buf, "%u\n", gpio_data->desired_brightness); } -static ssize_t gpio_trig_brightness_store(struct device *dev, +static ssize_t desired_brightness_store(struct device *dev, struct device_attribute *attr, const char *buf, size_t n) { struct gpio_trig_data *gpio_data = led_trigger_get_drvdata(dev); - unsigned desired_brightness; + u8 desired_brightness; int ret; - ret = sscanf(buf, "%u", &desired_brightness); - if (ret < 1 || desired_brightness > 255) { - dev_err(dev, "invalid value\n"); - return -EINVAL; - } + ret = kstrtou8(buf, 10, &desired_brightness); + if (ret) + return ret; gpio_data->desired_brightness = desired_brightness; return n; } -static DEVICE_ATTR(desired_brightness, 0644, gpio_trig_brightness_show, - gpio_trig_brightness_store); +static DEVICE_ATTR_RW(desired_brightness); static struct attribute *gpio_trig_attrs[] = { &dev_attr_desired_brightness.attr, @@ -89,10 +86,7 @@ static int gpio_trig_activate(struct led_classdev *led) * The generic property "trigger-sources" is followed, * and we hope that this is a GPIO. */ - gpio_data->gpiod = fwnode_gpiod_get_index(dev->fwnode, - "trigger-sources", - 0, GPIOD_IN, - "led-trigger"); + gpio_data->gpiod = gpiod_get_optional(dev, "trigger-sources", GPIOD_IN); if (IS_ERR(gpio_data->gpiod)) { ret = PTR_ERR(gpio_data->gpiod); kfree(gpio_data); @@ -104,6 +98,8 @@ static int gpio_trig_activate(struct led_classdev *led) return -EINVAL; } + gpiod_set_consumer_name(gpio_data->gpiod, "led-trigger"); + gpio_data->led = led; led_set_trigger_data(led, gpio_data); diff --git a/drivers/leds/trigger/ledtrig-netdev.c b/drivers/leds/trigger/ledtrig-netdev.c index d76214f..8e54758 100644 --- a/drivers/leds/trigger/ledtrig-netdev.c +++ b/drivers/leds/trigger/ledtrig-netdev.c @@ -38,6 +38,16 @@ * tx - LED blinks on transmitted data * rx - LED blinks on receive data * + * Note: If the user selects a mode that is not supported by hw, default + * behavior is to fall back to software control of the LED. However not every + * hw supports software control. LED callbacks brightness_set() and + * brightness_set_blocking() are NULL in this case. hw_control_is_supported() + * should use available means supported by hw to inform the user that selected + * mode isn't supported by hw. This could be switching off the LED or any + * hw blink mode. If software control fallback isn't possible, we return + * -EOPNOTSUPP to the user, but still store the selected mode. This is needed + * in case an intermediate unsupported mode is necessary to switch from one + * supported mode to another. */ struct led_netdev_data { @@ -99,6 +109,18 @@ static void set_baseline_state(struct led_netdev_data *trigger_data) trigger_data->link_speed == SPEED_1000) blink_on = true; + if (test_bit(TRIGGER_NETDEV_LINK_2500, &trigger_data->mode) && + trigger_data->link_speed == SPEED_2500) + blink_on = true; + + if (test_bit(TRIGGER_NETDEV_LINK_5000, &trigger_data->mode) && + trigger_data->link_speed == SPEED_5000) + blink_on = true; + + if (test_bit(TRIGGER_NETDEV_LINK_10000, &trigger_data->mode) && + trigger_data->link_speed == SPEED_10000) + blink_on = true; + if (test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &trigger_data->mode) && trigger_data->duplex == DUPLEX_HALF) blink_on = true; @@ -289,6 +311,9 @@ static ssize_t netdev_led_attr_show(struct device *dev, char *buf, case TRIGGER_NETDEV_LINK_10: case TRIGGER_NETDEV_LINK_100: case TRIGGER_NETDEV_LINK_1000: + case TRIGGER_NETDEV_LINK_2500: + case TRIGGER_NETDEV_LINK_5000: + case TRIGGER_NETDEV_LINK_10000: case TRIGGER_NETDEV_HALF_DUPLEX: case TRIGGER_NETDEV_FULL_DUPLEX: case TRIGGER_NETDEV_TX: @@ -306,6 +331,7 @@ static ssize_t netdev_led_attr_store(struct device *dev, const char *buf, size_t size, enum led_trigger_netdev_modes attr) { struct led_netdev_data *trigger_data = led_trigger_get_drvdata(dev); + struct led_classdev *led_cdev = trigger_data->led_cdev; unsigned long state, mode = trigger_data->mode; int ret; int bit; @@ -319,6 +345,9 @@ static ssize_t netdev_led_attr_store(struct device *dev, const char *buf, case TRIGGER_NETDEV_LINK_10: case TRIGGER_NETDEV_LINK_100: case TRIGGER_NETDEV_LINK_1000: + case TRIGGER_NETDEV_LINK_2500: + case TRIGGER_NETDEV_LINK_5000: + case TRIGGER_NETDEV_LINK_10000: case TRIGGER_NETDEV_HALF_DUPLEX: case TRIGGER_NETDEV_FULL_DUPLEX: case TRIGGER_NETDEV_TX: @@ -337,7 +366,10 @@ static ssize_t netdev_led_attr_store(struct device *dev, const char *buf, if (test_bit(TRIGGER_NETDEV_LINK, &mode) && (test_bit(TRIGGER_NETDEV_LINK_10, &mode) || test_bit(TRIGGER_NETDEV_LINK_100, &mode) || - test_bit(TRIGGER_NETDEV_LINK_1000, &mode))) + test_bit(TRIGGER_NETDEV_LINK_1000, &mode) || + test_bit(TRIGGER_NETDEV_LINK_2500, &mode) || + test_bit(TRIGGER_NETDEV_LINK_5000, &mode) || + test_bit(TRIGGER_NETDEV_LINK_10000, &mode))) return -EINVAL; cancel_delayed_work_sync(&trigger_data->work); @@ -345,6 +377,10 @@ static ssize_t netdev_led_attr_store(struct device *dev, const char *buf, trigger_data->mode = mode; trigger_data->hw_control = can_hw_control(trigger_data); + if (!led_cdev->brightness_set && !led_cdev->brightness_set_blocking && + !trigger_data->hw_control) + return -EOPNOTSUPP; + set_baseline_state(trigger_data); return size; @@ -367,6 +403,9 @@ DEFINE_NETDEV_TRIGGER(link, TRIGGER_NETDEV_LINK); DEFINE_NETDEV_TRIGGER(link_10, TRIGGER_NETDEV_LINK_10); DEFINE_NETDEV_TRIGGER(link_100, TRIGGER_NETDEV_LINK_100); DEFINE_NETDEV_TRIGGER(link_1000, TRIGGER_NETDEV_LINK_1000); +DEFINE_NETDEV_TRIGGER(link_2500, TRIGGER_NETDEV_LINK_2500); +DEFINE_NETDEV_TRIGGER(link_5000, TRIGGER_NETDEV_LINK_5000); +DEFINE_NETDEV_TRIGGER(link_10000, TRIGGER_NETDEV_LINK_10000); DEFINE_NETDEV_TRIGGER(half_duplex, TRIGGER_NETDEV_HALF_DUPLEX); DEFINE_NETDEV_TRIGGER(full_duplex, TRIGGER_NETDEV_FULL_DUPLEX); DEFINE_NETDEV_TRIGGER(tx, TRIGGER_NETDEV_TX); @@ -425,6 +464,9 @@ static struct attribute *netdev_trig_attrs[] = { &dev_attr_link_10.attr, &dev_attr_link_100.attr, &dev_attr_link_1000.attr, + &dev_attr_link_2500.attr, + &dev_attr_link_5000.attr, + &dev_attr_link_10000.attr, &dev_attr_full_duplex.attr, &dev_attr_half_duplex.attr, &dev_attr_rx.attr, @@ -522,6 +564,9 @@ static void netdev_trig_work(struct work_struct *work) test_bit(TRIGGER_NETDEV_LINK_10, &trigger_data->mode) || test_bit(TRIGGER_NETDEV_LINK_100, &trigger_data->mode) || test_bit(TRIGGER_NETDEV_LINK_1000, &trigger_data->mode) || + test_bit(TRIGGER_NETDEV_LINK_2500, &trigger_data->mode) || + test_bit(TRIGGER_NETDEV_LINK_5000, &trigger_data->mode) || + test_bit(TRIGGER_NETDEV_LINK_10000, &trigger_data->mode) || test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &trigger_data->mode) || test_bit(TRIGGER_NETDEV_FULL_DUPLEX, &trigger_data->mode); interval = jiffies_to_msecs( diff --git a/drivers/leds/trigger/ledtrig-panic.c b/drivers/leds/trigger/ledtrig-panic.c index 64abf2e..5a6b21b 100644 --- a/drivers/leds/trigger/ledtrig-panic.c +++ b/drivers/leds/trigger/ledtrig-panic.c @@ -64,10 +64,13 @@ static long led_panic_blink(int state) static int __init ledtrig_panic_init(void) { + led_trigger_register_simple("panic", &trigger); + if (!trigger) + return -ENOMEM; + atomic_notifier_chain_register(&panic_notifier_list, &led_trigger_panic_nb); - led_trigger_register_simple("panic", &trigger); panic_blink = led_panic_blink; return 0; } diff --git a/drivers/leds/trigger/ledtrig-tty.c b/drivers/leds/trigger/ledtrig-tty.c index 8ae0d2d..8cf1485 100644 --- a/drivers/leds/trigger/ledtrig-tty.c +++ b/drivers/leds/trigger/ledtrig-tty.c @@ -1,5 +1,6 @@ // SPDX-License-Identifier: GPL-2.0 +#include #include #include #include @@ -12,15 +13,45 @@ struct ledtrig_tty_data { struct led_classdev *led_cdev; struct delayed_work dwork; - struct mutex mutex; + struct completion sysfs; const char *ttyname; struct tty_struct *tty; int rx, tx; + bool mode_rx; + bool mode_tx; + bool mode_cts; + bool mode_dsr; + bool mode_dcd; + bool mode_rng; }; -static void ledtrig_tty_restart(struct ledtrig_tty_data *trigger_data) +/* Indicates which state the LED should now display */ +enum led_trigger_tty_state { + TTY_LED_BLINK, + TTY_LED_ENABLE, + TTY_LED_DISABLE, +}; + +enum led_trigger_tty_modes { + TRIGGER_TTY_RX = 0, + TRIGGER_TTY_TX, + TRIGGER_TTY_CTS, + TRIGGER_TTY_DSR, + TRIGGER_TTY_DCD, + TRIGGER_TTY_RNG, +}; + +static int ledtrig_tty_wait_for_completion(struct device *dev) { - schedule_delayed_work(&trigger_data->dwork, 0); + struct ledtrig_tty_data *trigger_data = led_trigger_get_drvdata(dev); + int ret; + + ret = wait_for_completion_timeout(&trigger_data->sysfs, + msecs_to_jiffies(LEDTRIG_TTY_INTERVAL * 20)); + if (ret == 0) + return -ETIMEDOUT; + + return ret; } static ssize_t ttyname_show(struct device *dev, @@ -28,14 +59,16 @@ static ssize_t ttyname_show(struct device *dev, { struct ledtrig_tty_data *trigger_data = led_trigger_get_drvdata(dev); ssize_t len = 0; + int completion; - mutex_lock(&trigger_data->mutex); + reinit_completion(&trigger_data->sysfs); + completion = ledtrig_tty_wait_for_completion(dev); + if (completion < 0) + return completion; if (trigger_data->ttyname) len = sprintf(buf, "%s\n", trigger_data->ttyname); - mutex_unlock(&trigger_data->mutex); - return len; } @@ -46,7 +79,7 @@ static ssize_t ttyname_store(struct device *dev, struct ledtrig_tty_data *trigger_data = led_trigger_get_drvdata(dev); char *ttyname; ssize_t ret = size; - bool running; + int completion; if (size > 0 && buf[size - 1] == '\n') size -= 1; @@ -59,9 +92,10 @@ static ssize_t ttyname_store(struct device *dev, ttyname = NULL; } - mutex_lock(&trigger_data->mutex); - - running = trigger_data->ttyname != NULL; + reinit_completion(&trigger_data->sysfs); + completion = ledtrig_tty_wait_for_completion(dev); + if (completion < 0) + return completion; kfree(trigger_data->ttyname); tty_kref_put(trigger_data->tty); @@ -69,29 +103,107 @@ static ssize_t ttyname_store(struct device *dev, trigger_data->ttyname = ttyname; - mutex_unlock(&trigger_data->mutex); - - if (ttyname && !running) - ledtrig_tty_restart(trigger_data); - return ret; } static DEVICE_ATTR_RW(ttyname); +static ssize_t ledtrig_tty_attr_show(struct device *dev, char *buf, + enum led_trigger_tty_modes attr) +{ + struct ledtrig_tty_data *trigger_data = led_trigger_get_drvdata(dev); + bool state; + + switch (attr) { + case TRIGGER_TTY_RX: + state = trigger_data->mode_rx; + break; + case TRIGGER_TTY_TX: + state = trigger_data->mode_tx; + break; + case TRIGGER_TTY_CTS: + state = trigger_data->mode_cts; + break; + case TRIGGER_TTY_DSR: + state = trigger_data->mode_dsr; + break; + case TRIGGER_TTY_DCD: + state = trigger_data->mode_dcd; + break; + case TRIGGER_TTY_RNG: + state = trigger_data->mode_rng; + break; + } + + return sysfs_emit(buf, "%u\n", state); +} + +static ssize_t ledtrig_tty_attr_store(struct device *dev, const char *buf, + size_t size, enum led_trigger_tty_modes attr) +{ + struct ledtrig_tty_data *trigger_data = led_trigger_get_drvdata(dev); + bool state; + int ret; + + ret = kstrtobool(buf, &state); + if (ret) + return ret; + + switch (attr) { + case TRIGGER_TTY_RX: + trigger_data->mode_rx = state; + break; + case TRIGGER_TTY_TX: + trigger_data->mode_tx = state; + break; + case TRIGGER_TTY_CTS: + trigger_data->mode_cts = state; + break; + case TRIGGER_TTY_DSR: + trigger_data->mode_dsr = state; + break; + case TRIGGER_TTY_DCD: + trigger_data->mode_dcd = state; + break; + case TRIGGER_TTY_RNG: + trigger_data->mode_rng = state; + break; + } + + return size; +} + +#define DEFINE_TTY_TRIGGER(trigger_name, trigger) \ + static ssize_t trigger_name##_show(struct device *dev, \ + struct device_attribute *attr, char *buf) \ + { \ + return ledtrig_tty_attr_show(dev, buf, trigger); \ + } \ + static ssize_t trigger_name##_store(struct device *dev, \ + struct device_attribute *attr, const char *buf, size_t size) \ + { \ + return ledtrig_tty_attr_store(dev, buf, size, trigger); \ + } \ + static DEVICE_ATTR_RW(trigger_name) + +DEFINE_TTY_TRIGGER(rx, TRIGGER_TTY_RX); +DEFINE_TTY_TRIGGER(tx, TRIGGER_TTY_TX); +DEFINE_TTY_TRIGGER(cts, TRIGGER_TTY_CTS); +DEFINE_TTY_TRIGGER(dsr, TRIGGER_TTY_DSR); +DEFINE_TTY_TRIGGER(dcd, TRIGGER_TTY_DCD); +DEFINE_TTY_TRIGGER(rng, TRIGGER_TTY_RNG); + static void ledtrig_tty_work(struct work_struct *work) { struct ledtrig_tty_data *trigger_data = container_of(work, struct ledtrig_tty_data, dwork.work); - struct serial_icounter_struct icount; + enum led_trigger_tty_state state = TTY_LED_DISABLE; + unsigned long interval = LEDTRIG_TTY_INTERVAL; + bool invert = false; + int status; int ret; - mutex_lock(&trigger_data->mutex); - - if (!trigger_data->ttyname) { - /* exit without rescheduling */ - mutex_unlock(&trigger_data->mutex); - return; - } + if (!trigger_data->ttyname) + goto out; /* try to get the tty corresponding to $ttyname */ if (!trigger_data->tty) { @@ -115,32 +227,83 @@ static void ledtrig_tty_work(struct work_struct *work) trigger_data->tty = tty; } - ret = tty_get_icount(trigger_data->tty, &icount); - if (ret) { - dev_info(trigger_data->tty->dev, "Failed to get icount, stopped polling\n"); - mutex_unlock(&trigger_data->mutex); - return; + status = tty_get_tiocm(trigger_data->tty); + if (status > 0) { + if (trigger_data->mode_cts) { + if (status & TIOCM_CTS) + state = TTY_LED_ENABLE; + } + + if (trigger_data->mode_dsr) { + if (status & TIOCM_DSR) + state = TTY_LED_ENABLE; + } + + if (trigger_data->mode_dcd) { + if (status & TIOCM_CAR) + state = TTY_LED_ENABLE; + } + + if (trigger_data->mode_rng) { + if (status & TIOCM_RNG) + state = TTY_LED_ENABLE; + } } - if (icount.rx != trigger_data->rx || - icount.tx != trigger_data->tx) { - unsigned long interval = LEDTRIG_TTY_INTERVAL; + /* + * The evaluation of rx/tx must be done after the evaluation + * of TIOCM_*, because rx/tx has priority. + */ + if (trigger_data->mode_rx || trigger_data->mode_tx) { + struct serial_icounter_struct icount; - led_blink_set_oneshot(trigger_data->led_cdev, &interval, - &interval, 0); + ret = tty_get_icount(trigger_data->tty, &icount); + if (ret) + goto out; - trigger_data->rx = icount.rx; - trigger_data->tx = icount.tx; + if (trigger_data->mode_tx && (icount.tx != trigger_data->tx)) { + trigger_data->tx = icount.tx; + invert = state == TTY_LED_ENABLE; + state = TTY_LED_BLINK; + } + + if (trigger_data->mode_rx && (icount.rx != trigger_data->rx)) { + trigger_data->rx = icount.rx; + invert = state == TTY_LED_ENABLE; + state = TTY_LED_BLINK; + } } out: - mutex_unlock(&trigger_data->mutex); + switch (state) { + case TTY_LED_BLINK: + led_blink_set_oneshot(trigger_data->led_cdev, &interval, + &interval, invert); + break; + case TTY_LED_ENABLE: + led_set_brightness(trigger_data->led_cdev, + trigger_data->led_cdev->blink_brightness); + break; + case TTY_LED_DISABLE: + fallthrough; + default: + led_set_brightness(trigger_data->led_cdev, LED_OFF); + break; + } + + complete_all(&trigger_data->sysfs); schedule_delayed_work(&trigger_data->dwork, msecs_to_jiffies(LEDTRIG_TTY_INTERVAL * 2)); } static struct attribute *ledtrig_tty_attrs[] = { &dev_attr_ttyname.attr, + &dev_attr_rx.attr, + &dev_attr_tx.attr, + &dev_attr_cts.attr, + &dev_attr_dsr.attr, + &dev_attr_dcd.attr, + &dev_attr_rng.attr, NULL }; ATTRIBUTE_GROUPS(ledtrig_tty); @@ -153,11 +316,17 @@ static int ledtrig_tty_activate(struct led_classdev *led_cdev) if (!trigger_data) return -ENOMEM; + /* Enable default rx/tx mode */ + trigger_data->mode_rx = true; + trigger_data->mode_tx = true; + led_set_trigger_data(led_cdev, trigger_data); INIT_DELAYED_WORK(&trigger_data->dwork, ledtrig_tty_work); trigger_data->led_cdev = led_cdev; - mutex_init(&trigger_data->mutex); + init_completion(&trigger_data->sysfs); + + schedule_delayed_work(&trigger_data->dwork, 0); return 0; } @@ -168,6 +337,10 @@ static void ledtrig_tty_deactivate(struct led_classdev *led_cdev) cancel_delayed_work_sync(&trigger_data->dwork); + kfree(trigger_data->ttyname); + tty_kref_put(trigger_data->tty); + trigger_data->tty = NULL; + kfree(trigger_data); } diff --git a/drivers/tty/tty_io.c b/drivers/tty/tty_io.c index 06414e4..e2e9340 100644 --- a/drivers/tty/tty_io.c +++ b/drivers/tty/tty_io.c @@ -2499,6 +2499,24 @@ static int send_break(struct tty_struct *tty, unsigned int duration) } /** + * tty_get_tiocm - get tiocm status register + * @tty: tty device + * + * Obtain the modem status bits from the tty driver if the feature + * is supported. + */ +int tty_get_tiocm(struct tty_struct *tty) +{ + int retval = -ENOTTY; + + if (tty->ops->tiocmget) + retval = tty->ops->tiocmget(tty); + + return retval; +} +EXPORT_SYMBOL_GPL(tty_get_tiocm); + +/** * tty_tiocmget - get modem status * @tty: tty device * @p: pointer to result @@ -2510,14 +2528,12 @@ static int send_break(struct tty_struct *tty, unsigned int duration) */ static int tty_tiocmget(struct tty_struct *tty, int __user *p) { - int retval = -ENOTTY; + int retval; - if (tty->ops->tiocmget) { - retval = tty->ops->tiocmget(tty); + retval = tty_get_tiocm(tty); + if (retval >= 0) + retval = put_user(retval, p); - if (retval >= 0) - retval = put_user(retval, p); - } return retval; } diff --git a/include/linux/leds.h b/include/linux/leds.h index aa16dc2..4754b02 100644 --- a/include/linux/leds.h +++ b/include/linux/leds.h @@ -527,23 +527,6 @@ static inline void *led_get_trigger_data(struct led_classdev *led_cdev) return led_cdev->trigger_data; } -/** - * led_trigger_rename_static - rename a trigger - * @name: the new trigger name - * @trig: the LED trigger to rename - * - * Change a LED trigger name by copying the string passed in - * name into current trigger name, which MUST be large - * enough for the new string. - * - * Note that name must NOT point to the same string used - * during LED registration, as that could lead to races. - * - * This is meant to be used on triggers with statically - * allocated name. - */ -void led_trigger_rename_static(const char *name, struct led_trigger *trig); - #define module_led_trigger(__led_trigger) \ module_driver(__led_trigger, led_trigger_register, \ led_trigger_unregister) @@ -588,6 +571,9 @@ enum led_trigger_netdev_modes { TRIGGER_NETDEV_LINK_10, TRIGGER_NETDEV_LINK_100, TRIGGER_NETDEV_LINK_1000, + TRIGGER_NETDEV_LINK_2500, + TRIGGER_NETDEV_LINK_5000, + TRIGGER_NETDEV_LINK_10000, TRIGGER_NETDEV_HALF_DUPLEX, TRIGGER_NETDEV_FULL_DUPLEX, TRIGGER_NETDEV_TX, diff --git a/include/linux/tty.h b/include/linux/tty.h index 4b6340a..d219a11 100644 --- a/include/linux/tty.h +++ b/include/linux/tty.h @@ -419,6 +419,7 @@ bool tty_unthrottle_safe(struct tty_struct *tty); int tty_do_resize(struct tty_struct *tty, struct winsize *ws); int tty_get_icount(struct tty_struct *tty, struct serial_icounter_struct *icount); +int tty_get_tiocm(struct tty_struct *tty); int is_current_pgrp_orphaned(void); void tty_hangup(struct tty_struct *tty); void tty_vhangup(struct tty_struct *tty);