Merge branch 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
Merge commit. Changes below are compared with the first parent: fa7b906e.
Changes
33 files changed · +2729 −362
Only the first 600 diff lines are shown. Download the complete patch.
Documentation/feature-removal-schedule.txt
View filediff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt
index 2193be5..5ddbe35 100644
--- a/Documentation/feature-removal-schedule.txt
+++ b/Documentation/feature-removal-schedule.txt
@@ -318,6 +318,14 @@ Who: Jean Delvare <[email protected]>
---------------------------
+What: fscher and fscpos drivers
+When: June 2009
+Why: Deprecated by the new fschmd driver.
+Who: Hans de Goede <[email protected]>
+ Jean Delvare <[email protected]>
+
+---------------------------
+
What: SELinux "compat_net" functionality
When: 2.6.30 at the earliest
Why: In 2.6.18 the Secmark concept was introduced to replace the "compat_net"
Documentation/hwmon/f71882fg
View filediff --git a/Documentation/hwmon/f71882fg b/Documentation/hwmon/f71882fg
new file mode 100644
index 0000000..a832126
--- /dev/null
+++ b/Documentation/hwmon/f71882fg
@@ -0,0 +1,89 @@
+Kernel driver f71882fg
+======================
+
+Supported chips:
+ * Fintek F71882FG and F71883FG
+ Prefix: 'f71882fg'
+ Addresses scanned: none, address read from Super I/O config space
+ Datasheet: Available from the Fintek website
+ * Fintek F71862FG and F71863FG
+ Prefix: 'f71862fg'
+ Addresses scanned: none, address read from Super I/O config space
+ Datasheet: Available from the Fintek website
+ * Fintek F8000
+ Prefix: 'f8000'
+ Addresses scanned: none, address read from Super I/O config space
+ Datasheet: Not public
+
+Author: Hans de Goede <[email protected]>
+
+
+Description
+-----------
+
+Fintek F718xxFG/F8000 Super I/O chips include complete hardware monitoring
+capabilities. They can monitor up to 9 voltages (3 for the F8000), 4 fans and
+3 temperature sensors.
+
+These chips also have fan controlling features, using either DC or PWM, in
+three different modes (one manual, two automatic).
+
+The driver assumes that no more than one chip is present, which seems
+reasonable.
+
+
+Monitoring
+----------
+
+The Voltage, Fan and Temperature Monitoring uses the standard sysfs
+interface as documented in sysfs-interface, without any exceptions.
+
+
+Fan Control
+-----------
+
+Both PWM (pulse-width modulation) and DC fan speed control methods are
+supported. The right one to use depends on external circuitry on the
+motherboard, so the driver assumes that the BIOS set the method
+properly.
+
+There are 2 modes to specify the speed of the fan, PWM duty cycle (or DC
+voltage) mode, where 0-100% duty cycle (0-100% of 12V) is specified. And RPM
+mode where the actual RPM of the fan (as measured) is controlled and the speed
+gets specified as 0-100% of the fan#_full_speed file.
+
+Since both modes work in a 0-100% (mapped to 0-255) scale, there isn't a
+whole lot of a difference when modifying fan control settings. The only
+important difference is that in RPM mode the 0-100% controls the fan speed
+between 0-100% of fan#_full_speed. It is assumed that if the BIOS programs
+RPM mode, it will also set fan#_full_speed properly, if it does not then
+fan control will not work properly, unless you set a sane fan#_full_speed
+value yourself.
+
+Switching between these modes requires re-initializing a whole bunch of
+registers, so the mode which the BIOS has set is kept. The mode is
+printed when loading the driver.
+
+Three different fan control modes are supported; the mode number is written
+to the pwm#_enable file. Note that not all modes are supported on all
+chips, and some modes may only be available in RPM / PWM mode on the F8000.
+Writing an unsupported mode will result in an invalid parameter error.
+
+* 1: Manual mode
+ You ask for a specific PWM duty cycle / DC voltage or a specific % of
+ fan#_full_speed by writing to the pwm# file. This mode is only
+ available on the F8000 if the fan channel is in RPM mode.
+
+* 2: Normal auto mode
+ You can define a number of temperature/fan speed trip points, which % the
+ fan should run at at this temp and which temp a fan should follow using the
+ standard sysfs interface. The number and type of trip points is chip
+ depended, see which files are available in sysfs.
+ Fan/PWM channel 3 of the F8000 is always in this mode!
+
+* 3: Thermostat mode (Only available on the F8000 when in duty cycle mode)
+ The fan speed is regulated to keep the temp the fan is mapped to between
+ temp#_auto_point2_temp and temp#_auto_point3_temp.
+
+Both of the automatic modes require that pwm1 corresponds to fan1, pwm2 to
+fan2 and pwm3 to fan3.
Documentation/hwmon/it87
View filediff --git a/Documentation/hwmon/it87 b/Documentation/hwmon/it87
index 042c041..659315d 100644
--- a/Documentation/hwmon/it87
+++ b/Documentation/hwmon/it87
@@ -26,6 +26,10 @@ Supported chips:
Datasheet: Publicly available at the ITE website
http://www.ite.com.tw/product_info/file/pc/IT8718F_V0.2.zip
http://www.ite.com.tw/product_info/file/pc/IT8718F_V0%203_(for%20C%20version).zip
+ * IT8720F
+ Prefix: 'it8720'
+ Addresses scanned: from Super I/O config space (8 I/O ports)
+ Datasheet: Not yet publicly available.
* SiS950 [clone of IT8705F]
Prefix: 'it87'
Addresses scanned: from Super I/O config space (8 I/O ports)
@@ -71,7 +75,7 @@ Description
-----------
This driver implements support for the IT8705F, IT8712F, IT8716F,
-IT8718F, IT8726F and SiS950 chips.
+IT8718F, IT8720F, IT8726F and SiS950 chips.
These chips are 'Super I/O chips', supporting floppy disks, infrared ports,
joysticks and other miscellaneous stuff. For hardware monitoring, they
@@ -84,19 +88,19 @@ the IT8716F and late IT8712F have 6. They are shared with other functions
though, so the functionality may not be available on a given system.
The driver dumbly assume it is there.
-The IT8718F also features VID inputs (up to 8 pins) but the value is
-stored in the Super-I/O configuration space. Due to technical limitations,
+The IT8718F and IT8720F also features VID inputs (up to 8 pins) but the value
+is stored in the Super-I/O configuration space. Due to technical limitations,
this value can currently only be read once at initialization time, so
the driver won't notice and report changes in the VID value. The two
upper VID bits share their pins with voltage inputs (in5 and in6) so you
can't have both on a given board.
-The IT8716F, IT8718F and later IT8712F revisions have support for
+The IT8716F, IT8718F, IT8720F and later IT8712F revisions have support for
2 additional fans. The additional fans are supported by the driver.
-The IT8716F and IT8718F, and late IT8712F and IT8705F also have optional
-16-bit tachometer counters for fans 1 to 3. This is better (no more fan
-clock divider mess) but not compatible with the older chips and
+The IT8716F, IT8718F and IT8720F, and late IT8712F and IT8705F also have
+optional 16-bit tachometer counters for fans 1 to 3. This is better (no more
+fan clock divider mess) but not compatible with the older chips and
revisions. The 16-bit tachometer mode is enabled by the driver when one
of the above chips is detected.
@@ -122,7 +126,7 @@ zero'; this is important for negative voltage measurements. All voltage
inputs can measure voltages between 0 and 4.08 volts, with a resolution of
0.016 volt. The battery voltage in8 does not have limit registers.
-The VID lines (IT8712F/IT8716F/IT8718F) encode the core voltage value:
+The VID lines (IT8712F/IT8716F/IT8718F/IT8720F) encode the core voltage value:
the voltage level your processor should work with. This is hardcoded by
the mainboard and/or processor itself. It is a value in volts.
Documentation/hwmon/lm70
View filediff --git a/Documentation/hwmon/lm70 b/Documentation/hwmon/lm70
index 2bdd3fe..0d24029 100644
--- a/Documentation/hwmon/lm70
+++ b/Documentation/hwmon/lm70
@@ -1,9 +1,11 @@
Kernel driver lm70
==================
-Supported chip:
+Supported chips:
* National Semiconductor LM70
Datasheet: http://www.national.com/pf/LM/LM70.html
+ * Texas Instruments TMP121/TMP123
+ Information: http://focus.ti.com/docs/prod/folders/print/tmp121.html
Author:
Kaiwan N Billimoria <[email protected]>
@@ -25,6 +27,14 @@ complement digital temperature (sent via the SIO line), is available in the
driver for interpretation. This driver makes use of the kernel's in-core
SPI support.
+As a real (in-tree) example of this "SPI protocol driver" interfacing
+with a "SPI master controller driver", see drivers/spi/spi_lm70llp.c
+and its associated documentation.
+
+The TMP121/TMP123 are very similar; main differences are 4 wire SPI inter-
+face (read only) and 13-bit temperature data (0.0625 degrees celsius reso-
+lution).
+
Thanks to
---------
Jean Delvare <[email protected]> for mentoring the hwmon-side driver
Documentation/hwmon/lm85
View filediff --git a/Documentation/hwmon/lm85 b/Documentation/hwmon/lm85
index 4006207..a136808 100644
--- a/Documentation/hwmon/lm85
+++ b/Documentation/hwmon/lm85
@@ -164,7 +164,7 @@ configured individually according to the following options.
temperature. (PWM value from 0 to 255)
* pwm#_auto_pwm_minctl - this flags selects for temp#_auto_temp_off temperature
- the bahaviour of fans. Write 1 to let fans spinning at
+ the behaviour of fans. Write 1 to let fans spinning at
pwm#_auto_pwm_min or write 0 to let them off.
NOTE: It has been reported that there is a bug in the LM85 that causes the flag
Documentation/hwmon/ltc4245
View filediff --git a/Documentation/hwmon/ltc4245 b/Documentation/hwmon/ltc4245
new file mode 100644
index 0000000..bae7a3a
--- /dev/null
+++ b/Documentation/hwmon/ltc4245
@@ -0,0 +1,81 @@
+Kernel driver ltc4245
+=====================
+
+Supported chips:
+ * Linear Technology LTC4245
+ Prefix: 'ltc4245'
+ Addresses scanned: 0x20-0x3f
+ Datasheet:
+ http://www.linear.com/pc/downloadDocument.do?navId=H0,C1,C1003,C1006,C1140,P19392,D13517
+
+Author: Ira W. Snyder <[email protected]>
+
+
+Description
+-----------
+
+The LTC4245 controller allows a board to be safely inserted and removed
+from a live backplane in multiple supply systems such as CompactPCI and
+PCI Express.
+
+
+Usage Notes
+-----------
+
+This driver does not probe for LTC4245 devices, due to the fact that some
+of the possible addresses are unfriendly to probing. You will need to use
+the "force" parameter to tell the driver where to find the device.
+
+Example: the following will load the driver for an LTC4245 at address 0x23
+on I2C bus #1:
+$ modprobe ltc4245 force=1,0x23
+
+
+Sysfs entries
+-------------
+
+The LTC4245 has built-in limits for over and under current warnings. This
+makes it very likely that the reference circuit will be used.
+
+This driver uses the values in the datasheet to change the register values
+into the values specified in the sysfs-interface document. The current readings
+rely on the sense resistors listed in Table 2: "Sense Resistor Values".
+
+in1_input 12v input voltage (mV)
+in2_input 5v input voltage (mV)
+in3_input 3v input voltage (mV)
+in4_input Vee (-12v) input voltage (mV)
+
+in1_min_alarm 12v input undervoltage alarm
+in2_min_alarm 5v input undervoltage alarm
+in3_min_alarm 3v input undervoltage alarm
+in4_min_alarm Vee (-12v) input undervoltage alarm
+
+curr1_input 12v current (mA)
+curr2_input 5v current (mA)
+curr3_input 3v current (mA)
+curr4_input Vee (-12v) current (mA)
+
+curr1_max_alarm 12v overcurrent alarm
+curr2_max_alarm 5v overcurrent alarm
+curr3_max_alarm 3v overcurrent alarm
+curr4_max_alarm Vee (-12v) overcurrent alarm
+
+in5_input 12v output voltage (mV)
+in6_input 5v output voltage (mV)
+in7_input 3v output voltage (mV)
+in8_input Vee (-12v) output voltage (mV)
+
+in5_min_alarm 12v output undervoltage alarm
+in6_min_alarm 5v output undervoltage alarm
+in7_min_alarm 3v output undervoltage alarm
+in8_min_alarm Vee (-12v) output undervoltage alarm
+
+in9_input GPIO #1 voltage data
+in10_input GPIO #2 voltage data
+in11_input GPIO #3 voltage data
+
+power1_input 12v power usage (mW)
+power2_input 5v power usage (mW)
+power3_input 3v power usage (mW)
+power4_input Vee (-12v) power usage (mW)
Documentation/spi/spi-lm70llp
View filediff --git a/Documentation/spi/spi-lm70llp b/Documentation/spi/spi-lm70llp
index 154bd02..34a9cfd 100644
--- a/Documentation/spi/spi-lm70llp
+++ b/Documentation/spi/spi-lm70llp
@@ -13,10 +13,20 @@ Description
This driver provides glue code connecting a National Semiconductor LM70 LLP
temperature sensor evaluation board to the kernel's SPI core subsystem.
+This is a SPI master controller driver. It can be used in conjunction with
+(layered under) the LM70 logical driver (a "SPI protocol driver").
In effect, this driver turns the parallel port interface on the eval board
into a SPI bus with a single device, which will be driven by the generic
LM70 driver (drivers/hwmon/lm70.c).
+
+Hardware Interfacing
+--------------------
+The schematic for this particular board (the LM70EVAL-LLP) is
+available (on page 4) here:
+
+ http://www.national.com/appinfo/tempsensors/files/LM70LLPEVALmanual.pdf
+
The hardware interfacing on the LM70 LLP eval board is as follows:
Parallel LM70 LLP
drivers/hwmon/Kconfig
View filediff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index c709e82..4b33bc8 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -284,11 +284,12 @@ config SENSORS_F71805F
will be called f71805f.
config SENSORS_F71882FG
- tristate "Fintek F71882FG and F71883FG"
+ tristate "Fintek F71862FG, F71882FG and F8000"
depends on EXPERIMENTAL
help
If you say yes here you get support for hardware monitoring
- features of the Fintek F71882FG and F71883FG Super-I/O chips.
+ features of the Fintek F71882FG/F71883FG, F71862FG/71863FG
+ and F8000 Super-I/O chips.
This driver can also be built as a module. If so, the module
will be called f71882fg.
@@ -304,9 +305,13 @@ config SENSORS_F75375S
will be called f75375s.
config SENSORS_FSCHER
- tristate "FSC Hermes"
+ tristate "FSC Hermes (DEPRECATED)"
depends on X86 && I2C
help
+ This driver is DEPRECATED please use the new merged fschmd
+ ("FSC Poseidon, Scylla, Hermes, Heimdall and Heracles") driver
+ instead.
+
If you say yes here you get support for Fujitsu Siemens
Computers Hermes sensor chips.
@@ -314,9 +319,13 @@ config SENSORS_FSCHER
will be called fscher.
config SENSORS_FSCPOS
- tristate "FSC Poseidon"
+ tristate "FSC Poseidon (DEPRECATED)"
depends on X86 && I2C
help
+ This driver is DEPRECATED please use the new merged fschmd
+ ("FSC Poseidon, Scylla, Hermes, Heimdall and Heracles") driver
+ instead.
+
If you say yes here you get support for Fujitsu Siemens
Computers Poseidon sensor chips.
@@ -325,14 +334,15 @@ config SENSORS_FSCPOS
config SENSORS_FSCHMD
tristate "FSC Poseidon, Scylla, Hermes, Heimdall and Heracles"
- depends on X86 && I2C && EXPERIMENTAL
+ depends on X86 && I2C
help
If you say yes here you get support for various Fujitsu Siemens
- Computers sensor chips.
+ Computers sensor chips, including support for the integrated
+ watchdog.
- This is a new merged driver for FSC sensor chips which is intended
- as a replacment for the fscpos, fscscy and fscher drivers and adds
- support for several other FCS sensor chips.
+ This is a merged driver for FSC sensor chips replacing the fscpos,
+ fscscy and fscher drivers and adding support for several other FSC
+ sensor chips.
This driver can also be built as a module. If so, the module
will be called fschmd.
@@ -399,7 +409,8 @@ config SENSORS_IT87
select HWMON_VID
help
If you say yes here you get support for ITE IT8705F, IT8712F,
- IT8716F, IT8718F and IT8726F sensor chips, and the SiS960 clone.
+ IT8716F, IT8718F, IT8720F and IT8726F sensor chips, and the
+ SiS960 clone.
This driver can also be built as a module. If so, the module
will be called it87.
@@ -417,11 +428,12 @@ config SENSORS_LM63
will be called lm63.
config SENSORS_LM70
- tristate "National Semiconductor LM70"
+ tristate "National Semiconductor LM70 / Texas Instruments TMP121"
depends on SPI_MASTER && EXPERIMENTAL
help
If you say yes here you get support for the National Semiconductor
- LM70 digital temperature sensor chip.
+ LM70 and Texas Instruments TMP121/TMP123 digital temperature
+ sensor chips.
This driver can also be built as a module. If so, the module
will be called lm70.
@@ -548,6 +560,17 @@ config SENSORS_LM93
This driver can also be built as a module. If so, the module
will be called lm93.
+config SENSORS_LTC4245
+ tristate "Linear Technology LTC4245"
+ depends on I2C && EXPERIMENTAL
+ default n
+ help
+ If you say yes here you get support for Linear Technology LTC4245
+ Multiple Supply Hot Swap Controller I2C interface.
+
+ This driver can also be built as a module. If so, the module will
+ be called ltc4245.
+
config SENSORS_MAX1111
tristate "Maxim MAX1111 Multichannel, Serial 8-bit ADC chip"
depends on SPI_MASTER
drivers/hwmon/Makefile
View filediff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 58fc5be..8fd124e 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -62,6 +62,7 @@ obj-$(CONFIG_SENSORS_LM87) += lm87.o
obj-$(CONFIG_SENSORS_LM90) += lm90.o
obj-$(CONFIG_SENSORS_LM92) += lm92.o
obj-$(CONFIG_SENSORS_LM93) += lm93.o
+obj-$(CONFIG_SENSORS_LTC4245) += ltc4245.o
obj-$(CONFIG_SENSORS_MAX1111) += max1111.o
obj-$(CONFIG_SENSORS_MAX1619) += max1619.o
obj-$(CONFIG_SENSORS_MAX6650) += max6650.o
drivers/hwmon/asb100.c
View filediff --git a/drivers/hwmon/asb100.c b/drivers/hwmon/asb100.c
index 8a45a2e..8acf829 100644
--- a/drivers/hwmon/asb100.c
+++ b/drivers/hwmon/asb100.c
@@ -53,7 +53,10 @@ static const unsigned short normal_i2c[] = { 0x2d, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(asb100);
-I2C_CLIENT_MODULE_PARM(force_subclients, "List of subclient addresses: "
+
+static unsigned short force_subclients[4];
+module_param_array(force_subclients, short, NULL, 0);
+MODULE_PARM_DESC(force_subclients, "List of subclient addresses: "
"{bus, clientaddr, subclientaddr1, subclientaddr2}");
/* Voltage IN registers 0-6 */
drivers/hwmon/dme1737.c
View filediff --git a/drivers/hwmon/dme1737.c b/drivers/hwmon/dme1737.c
index 27a5d39..3df202a 100644
--- a/drivers/hwmon/dme1737.c
+++ b/drivers/hwmon/dme1737.c
@@ -34,6 +34,7 @@
#include <linux/hwmon-vid.h>
#include <linux/err.h>
#include <linux/mutex.h>
+#include <linux/acpi.h>
#include <asm/io.h>
/* ISA device, if found */
@@ -2361,6 +2362,10 @@ static int __init dme1737_isa_device_add(unsigned short addr)
};
int err;
+ err = acpi_check_resource_conflict(&res);
+ if (err)
+ goto exit;
+
if (!(pdev = platform_device_alloc("dme1737", addr))) {
printk(KERN_ERR "dme1737: Failed to allocate device.\n");
err = -ENOMEM;
drivers/hwmon/f71805f.c
View filediff --git a/drivers/hwmon/f71805f.c b/drivers/hwmon/f71805f.c
index 7a14a2d..8998765 100644
--- a/drivers/hwmon/f71805f.c
+++ b/drivers/hwmon/f71805f.c
@@ -39,6 +39,7 @@
#include <linux/mutex.h>
#include <linux/sysfs.h>
#include <linux/ioport.h>
+#include <linux/acpi.h>
#include <asm/io.h>
static unsigned short force_id;
@@ -1455,6 +1456,10 @@ static int __init f71805f_device_add(unsigned short address,
}
res.name = pdev->name;
+ err = acpi_check_resource_conflict(&res);
+ if (err)
+ goto exit_device_put;
+
err = platform_device_add_resources(pdev, &res, 1);
if (err) {
printk(KERN_ERR DRVNAME ": Device resource addition failed "
drivers/hwmon/f71882fg.c
View filediff --git a/drivers/hwmon/f71882fg.c b/drivers/hwmon/f71882fg.c
index 67067e9..609caff 100644
--- a/drivers/hwmon/f71882fg.c
+++ b/drivers/hwmon/f71882fg.c
@@ -1,6 +1,6 @@
/***************************************************************************
* Copyright (C) 2006 by Hans Edgington <[email protected]> *
- * Copyright (C) 2007 by Hans de Goede <[email protected]> *
+ * Copyright (C) 2007,2008 by Hans de Goede <[email protected]> *
* *
* This program is free software; you can redistribute it and/or modify *
* it under the terms of the GNU General Public License as published by *
@@ -27,11 +27,12 @@
#include <linux/hwmon-sysfs.h>
#include <linux/err.h>
#include <linux/mutex.h>
-#include <asm/io.h>
+#include <linux/io.h>
+#include <linux/acpi.h>
#define DRVNAME "f71882fg"
-#define SIO_F71882FG_LD_HWM 0x04 /* Hardware monitor logical device*/
+#define SIO_F71882FG_LD_HWM 0x04 /* Hardware monitor logical device */
#define SIO_UNLOCK_KEY 0x87 /* Key to enable Super-I/O */
#define SIO_LOCK_KEY 0xAA /* Key to diasble Super-I/O */
@@ -43,7 +44,9 @@
#define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */
#define SIO_FINTEK_ID 0x1934 /* Manufacturers ID */
+#define SIO_F71862_ID 0x0601 /* Chipset ID */
#define SIO_F71882_ID 0x0541 /* Chipset ID */
+#define SIO_F8000_ID 0x0581 /* Chipset ID */
#define REGION_LENGTH 8
#define ADDR_REG_OFFSET 5
@@ -51,25 +54,36 @@
#define F71882FG_REG_PECI 0x0A
-#define F71882FG_REG_IN_STATUS 0x12
-#define F71882FG_REG_IN_BEEP 0x13
+#define F71882FG_REG_IN_STATUS 0x12 /* f71882fg only */
+#define F71882FG_REG_IN_BEEP 0x13 /* f71882fg only */
#define F71882FG_REG_IN(nr) (0x20 + (nr))
-#define F71882FG_REG_IN1_HIGH 0x32
+#define F71882FG_REG_IN1_HIGH 0x32 /* f71882fg only */
#define F71882FG_REG_FAN(nr) (0xA0 + (16 * (nr)))
+#define F71882FG_REG_FAN_TARGET(nr) (0xA2 + (16 * (nr)))
+#define F71882FG_REG_FAN_FULL_SPEED(nr) (0xA4 + (16 * (nr)))
#define F71882FG_REG_FAN_STATUS 0x92
#define F71882FG_REG_FAN_BEEP 0x93
-#define F71882FG_REG_TEMP(nr) (0x72 + 2 * (nr))
-#define F71882FG_REG_TEMP_OVT(nr) (0x82 + 2 * (nr))
-#define F71882FG_REG_TEMP_HIGH(nr) (0x83 + 2 * (nr))
+#define F71882FG_REG_TEMP(nr) (0x70 + 2 * (nr))
+#define F71882FG_REG_TEMP_OVT(nr) (0x80 + 2 * (nr))
+#define F71882FG_REG_TEMP_HIGH(nr) (0x81 + 2 * (nr))
#define F71882FG_REG_TEMP_STATUS 0x62
#define F71882FG_REG_TEMP_BEEP 0x63
-#define F71882FG_REG_TEMP_HYST1 0x6C
-#define F71882FG_REG_TEMP_HYST23 0x6D
+#define F71882FG_REG_TEMP_HYST(nr) (0x6C + (nr))
#define F71882FG_REG_TEMP_TYPE 0x6B
#define F71882FG_REG_TEMP_DIODE_OPEN 0x6F
+#define F71882FG_REG_PWM(nr) (0xA3 + (16 * (nr)))
+#define F71882FG_REG_PWM_TYPE 0x94
+#define F71882FG_REG_PWM_ENABLE 0x96
+
+#define F71882FG_REG_FAN_HYST(nr) (0x98 + (nr))
+
+#define F71882FG_REG_POINT_PWM(pwm, point) (0xAA + (point) + (16 * (pwm)))
+#define F71882FG_REG_POINT_TEMP(pwm, point) (0xA6 + (point) + (16 * (pwm)))
+#define F71882FG_REG_POINT_MAPPING(nr) (0xAF + 16 * (nr))
+
#define F71882FG_REG_START 0x01
#define FAN_MIN_DETECT 366 /* Lowest detectable fanspeed */
@@ -78,7 +92,15 @@ static unsigned short force_id;
This diff is incomplete. Download the complete patch.
drivers/hwmon/fschmd.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/i5k_amb.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/it87.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/lm70.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/ltc4245.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/pc87360.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/pc87427.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/sis5595.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/smsc47b397.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/smsc47m1.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/via686a.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/vt1211.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/vt8231.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/w83627ehf.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/w83627hf.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/w83781d.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/w83791d.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/w83792d.c
View fileThis diff is incomplete. Download the complete patch.
drivers/hwmon/w83793.c
View fileThis diff is incomplete. Download the complete patch.
drivers/spi/spi_lm70llp.c
View fileThis diff is incomplete. Download the complete patch.