diff --git a/Documentation/ABI/testing/sysfs-class-power-surface b/Documentation/ABI/testing/sysfs-class-power-surface new file mode 100644 index 0000000..79cde4d --- /dev/null +++ b/Documentation/ABI/testing/sysfs-class-power-surface @@ -0,0 +1,15 @@ +What: /sys/class/power_supply//alarm +Date: April 2021 +KernelVersion: 5.13 +Contact: Maximilian Luz +Description: + Battery trip point. When the remaining battery capacity crosses this + value in either direction, the system will be notified and if + necessary woken. + + Set to zero to clear/disable. + + Access: Read, Write + + Valid values: In micro-Wh or micro-Ah, depending on the power unit + of the battery diff --git a/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt b/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt index cd2d7f5..38e54b3 100644 --- a/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt +++ b/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt @@ -17,6 +17,9 @@ Optional properties: chip's trigger line. If this property is not set, the trigger function is ignored and the chip is kept alive until an explicit kill signal is received +- trigger-delay-ms The number of milliseconds to wait after trigger line + assertion before executing shut down procedure. + The default is 2500ms. Example: @@ -24,6 +27,7 @@ ltc2952 { compatible = "lltc,ltc2952"; trigger-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + trigger-delay-ms = <2000>; watchdog-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; kill-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; }; diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt b/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt deleted file mode 100644 index f181e46..0000000 --- a/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt +++ /dev/null @@ -1,16 +0,0 @@ -=== AB8500 Battery Temperature Monitor Driver === - -The properties below describes the node for btemp driver. - -Required Properties: -- compatible = Shall be: "stericsson,ab8500-btemp" -- battery = Shall be battery specific information - - Example: - ab8500_btemp { - compatible = "stericsson,ab8500-btemp"; - battery = <&ab8500_battery>; - }; - -For information on battery specific node, Ref: -Documentation/devicetree/bindings/power/supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt b/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt deleted file mode 100644 index 56636f9..0000000 --- a/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt +++ /dev/null @@ -1,16 +0,0 @@ -=== AB8500 Charging Algorithm Driver === - -The properties below describes the node for chargalg driver. - -Required Properties: -- compatible = Shall be: "stericsson,ab8500-chargalg" -- battery = Shall be battery specific information - -Example: -ab8500_chargalg { - compatible = "stericsson,ab8500-chargalg"; - battery = <&ab8500_battery>; -}; - -For information on battery specific node, Ref: -Documentation/devicetree/bindings/power/supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt b/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt deleted file mode 100644 index 24ada03..0000000 --- a/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt +++ /dev/null @@ -1,25 +0,0 @@ -=== AB8500 Charger Driver === - -Required Properties: -- compatible = Shall be "stericsson,ab8500-charger" -- battery = Shall be battery specific information - Example: - ab8500_charger { - compatible = "stericsson,ab8500-charger"; - battery = <&ab8500_battery>; - }; - -- vddadc-supply: Supply for USB and Main charger - Example: - ab8500-charger { - vddadc-supply = <&ab8500_ldo_tvout_reg>; - } -- autopower_cfg: - Boolean value depicting the presence of 'automatic poweron after powerloss' - Example: - ab8500-charger { - autopower_cfg; - }; - -For information on battery specific node, Ref: -Documentation/devicetree/bindings/power/supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt b/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt deleted file mode 100644 index cb737a9..0000000 --- a/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt +++ /dev/null @@ -1,44 +0,0 @@ -Device-Tree bindings for charger of Active-semi ACT8945A Multi-Function Device - -Required properties: - - compatible: "active-semi,act8945a-charger". - - active-semi,chglev-gpios: charge current level phandle with args - as described in ../gpio/gpio.txt. - - active-semi,lbo-gpios: specify the low battery voltage detect phandle - with args as as described in ../gpio/gpio.txt. - - interrupts: where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. - -Optional properties: - - active-semi,input-voltage-threshold-microvolt: unit: mV; - Specifies the charger's input over-voltage threshold value; - The value can be: 6600, 7000, 7500, 8000; default: 6600 - - active-semi,precondition-timeout: unit: minutes; - Specifies the charger's PRECONDITION safety timer setting value; - The value can be: 40, 60, 80, 0; If 0, it means to disable this timer; - default: 40. - - active-semi,total-timeout: unit: hours; - Specifies the charger's total safety timer setting value; - The value can be: 3, 4, 5, 0; If 0, it means to disable this timer; - default: 3. - -Example: - pmic@5b { - compatible = "active-semi,act8945a"; - reg = <0x5b>; - - charger { - compatible = "active-semi,act8945a-charger"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>; - interrupt-parent = <&pioA>; - interrupts = <45 IRQ_TYPE_LEVEL_LOW>; - - active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>; - active-semi,lbo-gpios = <&pioA 72 GPIO_ACTIVE_LOW>; - active-semi,input-voltage-threshold-microvolt = <6600>; - active-semi,precondition-timeout = <40>; - active-semi,total-timeout = <3>; - }; - }; diff --git a/Documentation/devicetree/bindings/power/supply/active-semi,act8945a-charger.yaml b/Documentation/devicetree/bindings/power/supply/active-semi,act8945a-charger.yaml new file mode 100644 index 0000000..3f74bc1 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/active-semi,act8945a-charger.yaml @@ -0,0 +1,76 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/active-semi,act8945a-charger.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Active-semi ACT8945A Charger Function + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: active-semi,act8945a-charger + + interrupts: + maxItems: 1 + + active-semi,chglev-gpios: + maxItems: 1 + description: charge current level GPIO + + active-semi,lbo-gpios: + maxItems: 1 + description: low battery voltage detect GPIO + + active-semi,input-voltage-threshold-microvolt: + description: | + Specifies the charger's input over-voltage threshold value. + Despite the name, specified values are in millivolt (mV). + Defaults to 6.6 V + enum: [ 6600, 7000, 7500, 8000 ] + + active-semi,precondition-timeout: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Specifies the charger's PRECONDITION safety timer setting value in minutes. + If 0, it means to disable this timer. + Defaults to 40 minutes. + enum: [ 0, 40, 60, 80 ] + + active-semi,total-timeout: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Specifies the charger's total safety timer setting value in hours; + If 0, it means to disable this timer; + Defaults to 3 hours. + enum: [ 0, 3, 4, 5 ] + +required: + - compatible + - interrupts + - active-semi,chglev-gpios + - active-semi,lbo-gpios + +additionalProperties: false + +examples: + - | + #include + #include + pmic { + charger { + compatible = "active-semi,act8945a-charger"; + interrupt-parent = <&pioA>; + interrupts = <45 IRQ_TYPE_LEVEL_LOW>; + active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>; + active-semi,lbo-gpios = <&pioA 72 GPIO_ACTIVE_LOW>; + active-semi,input-voltage-threshold-microvolt = <6600>; + active-semi,precondition-timeout = <40>; + active-semi,total-timeout = <3>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt b/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt deleted file mode 100644 index 7a1fb53..0000000 --- a/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt +++ /dev/null @@ -1,25 +0,0 @@ -AXP20X and AXP22X PMICs' AC power supply - -Required Properties: - - compatible: One of: - "x-powers,axp202-ac-power-supply" - "x-powers,axp221-ac-power-supply" - "x-powers,axp813-ac-power-supply" - -This node is a subnode of the axp20x PMIC. - -The AXP20X can read the current current and voltage supplied by AC by -reading ADC channels from the AXP20X ADC. - -The AXP22X is only able to tell if an AC power supply is present and -usable. - -AXP813/AXP803 are able to limit current and supply voltage - -Example: - -&axp209 { - ac_power_supply: ac-power-supply { - compatible = "x-powers,axp202-ac-power-supply"; - }; -}; diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_battery.txt b/Documentation/devicetree/bindings/power/supply/axp20x_battery.txt deleted file mode 100644 index 41916f6..0000000 --- a/Documentation/devicetree/bindings/power/supply/axp20x_battery.txt +++ /dev/null @@ -1,20 +0,0 @@ -AXP20x and AXP22x battery power supply - -Required Properties: - - compatible, one of: - "x-powers,axp209-battery-power-supply" - "x-powers,axp221-battery-power-supply" - "x-powers,axp813-battery-power-supply" - -This node is a subnode of its respective PMIC DT node. - -The supported devices can read the battery voltage, charge and discharge -currents of the battery by reading ADC channels from the ADC. - -Example: - -&axp209 { - battery_power_supply: battery-power-supply { - compatible = "x-powers,axp209-battery-power-supply"; - } -}; diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt b/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt deleted file mode 100644 index b2d4968..0000000 --- a/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt +++ /dev/null @@ -1,41 +0,0 @@ -AXP20x USB power supply - -Required Properties: --compatible: One of: "x-powers,axp202-usb-power-supply" - "x-powers,axp221-usb-power-supply" - "x-powers,axp223-usb-power-supply" - "x-powers,axp813-usb-power-supply" - -The AXP223 PMIC shares most of its behaviour with the AXP221 but has slight -variations such as the former being able to set the VBUS power supply max -current to 100mA, unlike the latter. - -This node is a subnode of the axp20x PMIC. - -Example: - -axp209: pmic@34 { - compatible = "x-powers,axp209"; - reg = <0x34>; - interrupt-parent = <&nmi_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #interrupt-cells = <1>; - - regulators { - x-powers,dcdc-freq = <1500>; - - vdd_cpu: dcdc2 { - regulator-always-on; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1450000>; - regulator-name = "vdd-cpu"; - }; - - ... - }; - - usb-power-supply: usb-power-supply { - compatible = "x-powers,axp202-usb-power-supply"; - }; -}; diff --git a/Documentation/devicetree/bindings/power/supply/battery.txt b/Documentation/devicetree/bindings/power/supply/battery.txt deleted file mode 100644 index a9f80cc..0000000 --- a/Documentation/devicetree/bindings/power/supply/battery.txt +++ /dev/null @@ -1,3 +0,0 @@ -The contents of this file has been moved to battery.yaml - -Please note that not all charger drivers respect all of the properties. diff --git a/Documentation/devicetree/bindings/power/supply/bq2415x.txt b/Documentation/devicetree/bindings/power/supply/bq2415x.txt deleted file mode 100644 index d0327f0..0000000 --- a/Documentation/devicetree/bindings/power/supply/bq2415x.txt +++ /dev/null @@ -1,47 +0,0 @@ -Binding for TI bq2415x Li-Ion Charger - -Required properties: -- compatible: Should contain one of the following: - * "ti,bq24150" - * "ti,bq24150" - * "ti,bq24150a" - * "ti,bq24151" - * "ti,bq24151a" - * "ti,bq24152" - * "ti,bq24153" - * "ti,bq24153a" - * "ti,bq24155" - * "ti,bq24156" - * "ti,bq24156a" - * "ti,bq24158" -- reg: integer, i2c address of the device. -- ti,current-limit: integer, initial maximum current charger can pull - from power supply in mA. -- ti,weak-battery-voltage: integer, weak battery voltage threshold in mV. - The chip will use slow precharge if battery voltage - is below this value. -- ti,battery-regulation-voltage: integer, maximum charging voltage in mV. -- ti,charge-current: integer, maximum charging current in mA. -- ti,termination-current: integer, charge will be terminated when current in - constant-voltage phase drops below this value (in mA). -- ti,resistor-sense: integer, value of sensing resistor in milliohm. - -Optional properties: -- ti,usb-charger-detection: phandle to usb charger detection device. - (required for auto mode) - -Example from Nokia N900: - -bq24150a { - compatible = "ti,bq24150a"; - reg = <0x6b>; - - ti,current-limit = <100>; - ti,weak-battery-voltage = <3400>; - ti,battery-regulation-voltage = <4200>; - ti,charge-current = <650>; - ti,termination-current = <100>; - ti,resistor-sense = <68>; - - ti,usb-charger-detection = <&isp1704>; -}; diff --git a/Documentation/devicetree/bindings/power/supply/bq2415x.yaml b/Documentation/devicetree/bindings/power/supply/bq2415x.yaml new file mode 100644 index 0000000..f8461f0 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq2415x.yaml @@ -0,0 +1,98 @@ +# SPDX-License-Identifier: GPL-2.0 +# Copyright (C) 2021 Sebastian Reichel +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/bq2415x.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Binding for TI bq2415x Li-Ion Charger + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + enum: + - ti,bq24150 + - ti,bq24150 + - ti,bq24150a + - ti,bq24151 + - ti,bq24151a + - ti,bq24152 + - ti,bq24153 + - ti,bq24153a + - ti,bq24155 + - ti,bq24156 + - ti,bq24156a + - ti,bq24158 + + reg: + maxItems: 1 + + ti,current-limit: + $ref: /schemas/types.yaml#/definitions/uint32 + description: initial maximum current charger can pull from power supply in mA. + + ti,weak-battery-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + weak battery voltage threshold in mV. + The chip will use slow precharge if battery voltage is below this value. + + ti,battery-regulation-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: maximum charging voltage in mV. + + ti,charge-current: + $ref: /schemas/types.yaml#/definitions/uint32 + description: maximum charging current in mA. + + ti,termination-current: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + charge will be terminated when current in constant-voltage phase drops + below this value (in mA). + + ti,resistor-sense: + $ref: /schemas/types.yaml#/definitions/uint32 + description: value of sensing resistor in milliohm. + + ti,usb-charger-detection: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to usb charger detection device (required for auto mode) + +required: + - compatible + - reg + - ti,current-limit + - ti,weak-battery-voltage + - ti,battery-regulation-voltage + - ti,charge-current + - ti,termination-current + - ti,resistor-sense + +additionalProperties: false + +examples: + - | + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + charger@6b { + compatible = "ti,bq24150a"; + reg = <0x6b>; + + ti,current-limit = <100>; + ti,weak-battery-voltage = <3400>; + ti,battery-regulation-voltage = <4200>; + ti,charge-current = <650>; + ti,termination-current = <100>; + ti,resistor-sense = <68>; + + ti,usb-charger-detection = <&isp1704>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/bq24190.txt b/Documentation/devicetree/bindings/power/supply/bq24190.txt deleted file mode 100644 index ffe2be4..0000000 --- a/Documentation/devicetree/bindings/power/supply/bq24190.txt +++ /dev/null @@ -1,61 +0,0 @@ -TI BQ24190 Li-Ion Battery Charger - -Required properties: -- compatible: contains one of the following: - * "ti,bq24190" - * "ti,bq24192" - * "ti,bq24192i" - * "ti,bq24196" -- reg: integer, I2C address of the charger. -- interrupts[-extended]: configuration for charger INT pin. - -Optional properties: -- monitored-battery: phandle of battery characteristics devicetree node - The charger uses the following battery properties: - + precharge-current-microamp: maximum charge current during precharge - phase (typically 20% of battery capacity). - + charge-term-current-microamp: a charge cycle terminates when the - battery voltage is above recharge threshold, and the current is below - this setting (typically 10% of battery capacity). - See also Documentation/devicetree/bindings/power/supply/battery.txt -- ti,system-minimum-microvolt: when power is connected and the battery is below - minimum system voltage, the system will be regulated above this setting. - -child nodes: -- usb-otg-vbus: - Usage: optional - Description: Regulator that is used to control the VBUS voltage direction for - either USB host mode or for charging on the OTG port. - -Notes: -- Some circuit boards wire the chip's "OTG" pin high (enabling 500mA default - charge current on USB SDP ports, among other features). To simulate this on - boards that wire the pin to a GPIO, set a gpio-hog. - -Example: - - bat: battery { - compatible = "simple-battery"; - precharge-current-microamp = <256000>; - charge-term-current-microamp = <128000>; - // etc. - }; - - bq24190: charger@6a { - compatible = "ti,bq24190"; - reg = <0x6a>; - interrupts-extended = <&gpiochip 10 IRQ_TYPE_EDGE_FALLING>; - monitored-battery = <&bat>; - ti,system-minimum-microvolt = <3200000>; - - usb_otg_vbus: usb-otg-vbus { }; - }; - - &twl_gpio { - otg { - gpio-hog; - gpios = <6 0>; - output-high; - line-name = "otg-gpio"; - }; - }; diff --git a/Documentation/devicetree/bindings/power/supply/bq24190.yaml b/Documentation/devicetree/bindings/power/supply/bq24190.yaml new file mode 100644 index 0000000..0d7cbbd --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq24190.yaml @@ -0,0 +1,92 @@ +# SPDX-License-Identifier: GPL-2.0 +# Copyright (C) 2021 Sebastian Reichel +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/bq24190.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Binding for TI BQ2419x Li-Ion Battery Charger + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + enum: + - ti,bq24190 + - ti,bq24192 + - ti,bq24192i + - ti,bq24196 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + usb-otg-vbus: + type: object + description: | + Regulator that is used to control the VBUS voltage direction for + either USB host mode or for charging on the OTG port + + ti,system-minimum-microvolt: + description: | + when power is connected and the battery is below minimum system voltage, + the system will be regulated above this setting. + + omit-battery-class: + type: boolean + description: | + If this property is set, the operating system does not try to create a + battery device. + + monitored-battery: + $ref: /schemas/types.yaml#/definitions/phandle + description: | + phandle to a "simple-battery" compatible node. + + This property must be a phandle to a node using the format described + in battery.yaml, with the following properties being required: + - precharge-current-microamp: maximum charge current during precharge phase + (typically 20% of battery capacity). + - charge-term-current-microamp: a charge cycle terminates when the battery voltage is + above recharge threshold, and the current is below this + setting (typically 10% of battery capacity). + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + #include + #include + + bat: battery { + compatible = "simple-battery"; + precharge-current-microamp = <256000>; + charge-term-current-microamp = <128000>; + }; + + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + charger@6a { + compatible = "ti,bq24190"; + reg = <0x6a>; + interrupt-parent = <&gpiochip>; + interrupts = <10 IRQ_TYPE_EDGE_FALLING>; + monitored-battery = <&bat>; + ti,system-minimum-microvolt = <3200000>; + + usb_otg_vbus: usb-otg-vbus { }; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/bq24257.txt b/Documentation/devicetree/bindings/power/supply/bq24257.txt deleted file mode 100644 index f8f5a16..0000000 --- a/Documentation/devicetree/bindings/power/supply/bq24257.txt +++ /dev/null @@ -1,62 +0,0 @@ -Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger - -Required properties: -- compatible: Should contain one of the following: - * "ti,bq24250" - * "ti,bq24251" - * "ti,bq24257" -- reg: integer, i2c address of the device. -- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in - conjunction with "interrupt-parent". -- ti,battery-regulation-voltage: integer, maximum charging voltage in uV. -- ti,charge-current: integer, maximum charging current in uA. -- ti,termination-current: integer, charge will be terminated when current in - constant-voltage phase drops below this value (in uA). - -Optional properties: -- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin. - This pin is not available on all devices however it should be used if - possible as this is the recommended way to obtain the charger's input PG - state. If this pin is not specified a software-based approach for PG - detection is used. -- ti,current-limit: The maximum current to be drawn from the charger's input - (in uA). If this property is not specified, the input limit current is - set automatically using USB D+/D- signal based charger type detection. - If the hardware does not support the D+/D- based detection, a default - of 500,000 is used (=500mA) instead. -- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If - not specified a default of 6,5000,000 (=6.5V) is used. -- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic - power path management (in uV). If not specified a default of 4,360,000 - (=4.36V) is used. - -Example: - -bq24257 { - compatible = "ti,bq24257"; - reg = <0x6a>; - interrupt-parent = <&gpio1>; - interrupts = <16 IRQ_TYPE_EDGE_BOTH>; - - pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; - - ti,battery-regulation-voltage = <4200000>; - ti,charge-current = <1000000>; - ti,termination-current = <50000>; -}; - -Example: - -bq24250 { - compatible = "ti,bq24250"; - reg = <0x6a>; - interrupt-parent = <&gpio1>; - interrupts = <16 IRQ_TYPE_EDGE_BOTH>; - - ti,battery-regulation-voltage = <4200000>; - ti,charge-current = <500000>; - ti,termination-current = <50000>; - ti,current-limit = <900000>; - ti,ovp-voltage = <9500000>; - ti,in-dpm-voltage = <4440000>; -}; diff --git a/Documentation/devicetree/bindings/power/supply/bq24257.yaml b/Documentation/devicetree/bindings/power/supply/bq24257.yaml new file mode 100644 index 0000000..3a0f6cd --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq24257.yaml @@ -0,0 +1,124 @@ +# SPDX-License-Identifier: GPL-2.0 +# Copyright (C) 2021 Sebastian Reichel +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/bq24257.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Binding for bq24250, bq24251 and bq24257 Li-Ion Charger + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + enum: + - ti,bq24250 + - ti,bq24251 + - ti,bq24257 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + ti,battery-regulation-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: maximum charging voltage in uV + + ti,charge-current: + $ref: /schemas/types.yaml#/definitions/uint32 + description: maximum charging current in uA + + ti,termination-current: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + charge will be terminated when current in constant-voltage phase + drops below this value (in uA) + + pg-gpios: + description: | + GPIO used for connecting the bq2425x device PG (Power Good) pin. + This pin is not available on all devices however it should be used if + possible as this is the recommended way to obtain the charger's input PG + state. If this pin is not specified a software-based approach for PG + detection is used. + maxItems: 1 + + ti,current-limit: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + The maximum current to be drawn from the charger's input (in uA). + If this property is not specified, the input limit current is set + automatically using USB D+/D- signal based charger type detection. + If the hardware does not support the D+/D- based detection, a default + of 500,000 is used (=500mA) instead. + + ti,ovp-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Configures the over voltage protection voltage (in uV). + If not specified a default of 6,5000,000 (=6.5V) is used. + + ti,in-dpm-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Configures the threshold input voltage for the dynamic power path management (in uV). + If not specified a default of 4,360,000 (=4.36V) is used. + +required: + - compatible + - reg + - interrupts + - ti,battery-regulation-voltage + - ti,charge-current + - ti,termination-current + +additionalProperties: false + +examples: + - | + #include + #include + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + charger@6a { + compatible = "ti,bq24257"; + reg = <0x6a>; + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_BOTH>; + + pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <1000000>; + ti,termination-current = <50000>; + }; + }; + - | + #include + #include + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + charger@6a { + compatible = "ti,bq24250"; + reg = <0x6a>; + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_BOTH>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <500000>; + ti,termination-current = <50000>; + ti,current-limit = <900000>; + ti,ovp-voltage = <9500000>; + ti,in-dpm-voltage = <4440000>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/bq24735.yaml b/Documentation/devicetree/bindings/power/supply/bq24735.yaml new file mode 100644 index 0000000..131be67 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq24735.yaml @@ -0,0 +1,89 @@ +# SPDX-License-Identifier: GPL-2.0 +# Copyright (C) 2021 Sebastian Reichel +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/bq24735.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Binding for TI BQ24735 Li-Ion Battery Charger + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: ti,bq24735 + + reg: + maxItems: 1 + + interrupts: + description: AC adapter plug event interrupt + maxItems: 1 + + ti,ac-detect-gpios: + maxItems: 1 + description: | + This GPIO is optionally used to read the AC adapter status. This is a Host GPIO + that is configured as an input and connected to the ACOK pin on the bq24735. + Note: for backwards compatibility reasons, the GPIO must be active on AC adapter + absence despite ACOK being active (high) on AC adapter presence. + + ti,charge-current: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Used to control and set the charging current. + This value must be between 128mA and 8.128A with a 64mA step resolution. + The POR value is 0x0000h. This number is in mA (e.g. 8192). + See spec for more information about the ChargeCurrent (0x14h) register. + + ti,charge-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Used to control and set the charging voltage. + This value must be between 1.024V and 19.2V with a 16mV step resolution. + The POR value is 0x0000h. This number is in mV (e.g. 19200). + See spec for more information about the ChargeVoltage (0x15h) register. + + ti,input-current: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Used to control and set the charger input current. + This value must be between 128mA and 8.064A with a 128mA step resolution. + The POR value is 0x1000h. This number is in mA (e.g. 8064). + See the spec for more information about the InputCurrent (0x3fh) register. + + ti,external-control: + type: boolean + description: | + Indicates that the charger is configured externally and that the host should not + attempt to enable/disable charging or set the charge voltage/current. + + poll-interval: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + If 'interrupts' is not specified, poll AC adapter presence with this interval (milliseconds). + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include + + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + charger@9 { + compatible = "ti,bq24735"; + reg = <0x9>; + ti,ac-detect-gpios = <&gpio 72 0x1>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/bq25890.txt b/Documentation/devicetree/bindings/power/supply/bq25890.txt deleted file mode 100644 index 805040c..0000000 --- a/Documentation/devicetree/bindings/power/supply/bq25890.txt +++ /dev/null @@ -1,60 +0,0 @@ -Binding for TI bq25890 Li-Ion Charger - -This driver will support the bq25892, the bq25896 and the bq25890. There are -other ICs in the same family but those have not been tested. - -Required properties: -- compatible: Should contain one of the following: - * "ti,bq25890" - * "ti,bq25892" - * "ti,bq25895" - * "ti,bq25896" -- reg: integer, i2c address of the device. -- interrupts: interrupt line; -- ti,battery-regulation-voltage: integer, maximum charging voltage (in uV); -- ti,charge-current: integer, maximum charging current (in uA); -- ti,termination-current: integer, charge will be terminated when current in - constant-voltage phase drops below this value (in uA); -- ti,precharge-current: integer, maximum charge current during precharge - phase (in uA); -- ti,minimum-sys-voltage: integer, when battery is charging and it is below - minimum system voltage, the system will be regulated above - minimum-sys-voltage setting (in uV); -- ti,boost-voltage: integer, VBUS voltage level in boost mode (in uV); -- ti,boost-max-current: integer, maximum allowed current draw in boost mode - (in uA). - -Optional properties: -- ti,boost-low-freq: boolean, if present boost mode frequency will be 500kHz, - otherwise 1.5MHz; -- ti,use-ilim-pin: boolean, if present the ILIM resistor will be used and the - input current will be the lower between the resistor setting and the IINLIM - register setting; -- ti,thermal-regulation-threshold: integer, temperature above which the charge - current is lowered, to avoid overheating (in degrees Celsius). If omitted, - the default setting will be used (120 degrees); -- ti,ibatcomp-micro-ohms: integer, value of a resistor in series with - the battery; -- ti,ibatcomp-clamp-microvolt: integer, maximum charging voltage adjustment due - to expected voltage drop on in-series resistor; - -Example: - -bq25890 { - compatible = "ti,bq25890"; - reg = <0x6a>; - - interrupt-parent = <&gpio1>; - interrupts = <16 IRQ_TYPE_EDGE_FALLING>; - - ti,battery-regulation-voltage = <4200000>; - ti,charge-current = <1000000>; - ti,termination-current = <50000>; - ti,precharge-current = <128000>; - ti,minimum-sys-voltage = <3600000>; - ti,boost-voltage = <5000000>; - ti,boost-max-current = <1000000>; - - ti,use-ilim-pin; - ti,thermal-regulation-threshold = <120>; -}; diff --git a/Documentation/devicetree/bindings/power/supply/bq25890.yaml b/Documentation/devicetree/bindings/power/supply/bq25890.yaml new file mode 100644 index 0000000..bf823b6 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq25890.yaml @@ -0,0 +1,123 @@ +# SPDX-License-Identifier: GPL-2.0 +# Copyright (C) 2021 Sebastian Reichel +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/bq25890.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Binding for bq25890, bq25892, bq25895 and bq25896 Li-Ion Charger + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + enum: + - ti,bq25890 + - ti,bq25892 + - ti,bq25895 + - ti,bq25896 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + ti,battery-regulation-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: maximum charging voltage (in uV) + + ti,charge-current: + $ref: /schemas/types.yaml#/definitions/uint32 + description: maximum charging current (in uA) + + ti,termination-current: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + charge will be terminated when current in constant-voltage phase + drops below this value (in uA) + + ti,precharge-current: + $ref: /schemas/types.yaml#/definitions/uint32 + description: maximum charge current during precharge phase (in uA) + + ti,minimum-sys-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + when battery is charging and it is below minimum system voltage, + the system will be regulated above minimum-sys-voltage setting (in uV) + + ti,boost-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: VBUS voltage level in boost mode (in uV) + + ti,boost-max-current: + $ref: /schemas/types.yaml#/definitions/uint32 + description: maximum allowed current draw in boost mode (in uA) + + ti,boost-low-freq: + description: boost mode frequency will be 500kHz, otherwise 1.5MHz + type: boolean + + ti,use-ilim-pin: + description: | + ILIM resistor will be used and the input current will be the lower + between the resistor setting and the IINLIM register setting + type: boolean + + ti,thermal-regulation-threshold: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + temperature above which the charge current is lowered, to avoid overheating + (in degrees Celsius). If omitted, the default setting will be used (120 degrees) + + ti,ibatcomp-micro-ohms: + description: value of a resistor in series with the battery (in Micro Ohms) + + ti,ibatcomp-clamp-microvolt: + description: max. charging voltage adjustment due to expected voltage drop on in-series resistor + +required: + - compatible + - reg + - interrupts + - ti,battery-regulation-voltage + - ti,charge-current + - ti,termination-current + - ti,precharge-current + - ti,minimum-sys-voltage + - ti,boost-voltage + - ti,boost-max-current + +additionalProperties: false + +examples: + - | + #include + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + charger@6a { + compatible = "ti,bq25890"; + reg = <0x6a>; + + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_FALLING>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <1000000>; + ti,termination-current = <50000>; + ti,precharge-current = <128000>; + ti,minimum-sys-voltage = <3600000>; + ti,boost-voltage = <5000000>; + ti,boost-max-current = <1000000>; + + ti,use-ilim-pin; + ti,thermal-regulation-threshold = <120>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/bq27xxx.yaml b/Documentation/devicetree/bindings/power/supply/bq27xxx.yaml index 45beefc..6af41da 100644 --- a/Documentation/devicetree/bindings/power/supply/bq27xxx.yaml +++ b/Documentation/devicetree/bindings/power/supply/bq27xxx.yaml @@ -52,6 +52,7 @@ properties: - ti,bq27z561 - ti,bq28z610 - ti,bq34z100 + - ti,bq78z100 reg: maxItems: 1 @@ -65,7 +66,7 @@ properties: - charge-full-design-microamp-hours - voltage-min-design-microvolt Both or neither of the *-full-design-*-hours properties must be set. - See Documentation/devicetree/bindings/power/supply/battery.txt + See Documentation/devicetree/bindings/power/supply/battery.yaml power-supplies: true diff --git a/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt b/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt deleted file mode 100644 index a04efa2..0000000 --- a/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt +++ /dev/null @@ -1,31 +0,0 @@ -Motorola CPCAP PMIC battery driver binding - -Required properties: -- compatible: Shall be "motorola,cpcap-battery" -- interrupts: Interrupt specifier for each name in interrupt-names -- interrupt-names: Should contain the following entries: - "lowbph", "lowbpl", "chrgcurr1", "battdetb" -- io-channels: IIO ADC channel specifier for each name in io-channel-names -- io-channel-names: Should contain the following entries: - "battdetb", "battp", "chg_isense", "batti" -- power-supplies: List of phandles for power-supplying devices, as - described in power_supply.txt. Typically a reference - to cpcap_charger. - -Example: - -cpcap_battery: battery { - compatible = "motorola,cpcap-battery"; - interrupts-extended = < - &cpcap 5 0 &cpcap 3 0 - &cpcap 20 0 &cpcap 54 0 - >; - interrupt-names = - "lowbph", "lowbpl", - "chrgcurr1", "battdetb"; - io-channels = <&cpcap_adc 0 &cpcap_adc 1 - &cpcap_adc 5 &cpcap_adc 6>; - io-channel-names = "battdetb", "battp", - "chg_isense", "batti"; - power-supplies = <&cpcap_charger>; -}; diff --git a/Documentation/devicetree/bindings/power/supply/cpcap-battery.yaml b/Documentation/devicetree/bindings/power/supply/cpcap-battery.yaml new file mode 100644 index 0000000..7153fd4 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/cpcap-battery.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: GPL-2.0 +# Copyright (C) 2021 Sebastian Reichel +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/cpcap-battery.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Motorola CPCAP PMIC battery + +maintainers: + - Tony Lindgren + - Sebastian Reichel + +description: | + Motorola CPCAP is a PMIC found in some mobile phones, e.g. + the Droid 4. This binding describes its battery fuel gauge + sub-function. + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: motorola,cpcap-battery + + interrupts: + items: + - description: eol interrupt + - description: low battery percentage interrupt + - description: critical battery percentage interrupt + - description: charger detect interrupt + - description: battery detect interrupt + - description: coulomb counter calibration interrupt + + interrupt-names: + items: + - const: eol + - const: lowbph + - const: lowbpl + - const: chrgcurr1 + - const: battdetb + - const: cccal + + io-channels: + items: + - description: battery temperature + - description: battery voltage + - description: battery charge current + - description: battery current + + io-channel-names: + items: + - const: battdetb + - const: battp + - const: chg_isense + - const: batti + + power-supplies: true + +required: + - compatible + - interrupts + - interrupt-names + - io-channels + - io-channel-names + - power-supplies + +additionalProperties: false + +examples: + - | + cpcap { + battery { + compatible = "motorola,cpcap-battery"; + interrupts-extended = + <&cpcap 6 0>, <&cpcap 5 0>, <&cpcap 3 0>, + <&cpcap 20 0>, <&cpcap 54 0>, <&cpcap 57 0>; + interrupt-names = + "eol", "lowbph", "lowbpl", + "chrgcurr1", "battdetb", "cccal"; + io-channels = <&cpcap_adc 0>, <&cpcap_adc 1>, + <&cpcap_adc 5>, <&cpcap_adc 6>; + io-channel-names = "battdetb", "battp", + "chg_isense", "batti"; + power-supplies = <&cpcap_charger>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/cpcap-charger.txt b/Documentation/devicetree/bindings/power/supply/cpcap-charger.txt deleted file mode 100644 index 6048f63..0000000 --- a/Documentation/devicetree/bindings/power/supply/cpcap-charger.txt +++ /dev/null @@ -1,40 +0,0 @@ -Motorola CPCAP PMIC battery charger binding - -Required properties: -- compatible: Shall be "motorola,mapphone-cpcap-charger" -- interrupts: Interrupt specifier for each name in interrupt-names -- interrupt-names: Should contain the following entries: - "chrg_det", "rvrs_chrg", "chrg_se1b", "se0conn", - "rvrs_mode", "chrgcurr2", "chrgcurr1", "vbusvld", - "battdetb" -- io-channels: IIO ADC channel specifier for each name in io-channel-names -- io-channel-names: Should contain the following entries: - "battdetb", "battp", "vbus", "chg_isense", "batti" - -Optional properties: -- mode-gpios: Optionally CPCAP charger can have a companion wireless - charge controller that is controlled with two GPIOs - that are active low. - -Example: - -cpcap_charger: charger { - compatible = "motorola,mapphone-cpcap-charger"; - interrupts-extended = < - &cpcap 13 0 &cpcap 12 0 &cpcap 29 0 &cpcap 28 0 - &cpcap 22 0 &cpcap 21 0 &cpcap 20 0 &cpcap 19 0 - &cpcap 54 0 - >; - interrupt-names = - "chrg_det", "rvrs_chrg", "chrg_se1b", "se0conn", - "rvrs_mode", "chrgcurr2", "chrgcurr1", "vbusvld", - "battdetb"; - mode-gpios = <&gpio3 29 GPIO_ACTIVE_LOW - &gpio3 23 GPIO_ACTIVE_LOW>; - io-channels = <&cpcap_adc 0 &cpcap_adc 1 - &cpcap_adc 2 &cpcap_adc 5 - &cpcap_adc 6>; - io-channel-names = "battdetb", "battp", - "vbus", "chg_isense", - "batti"; -}; diff --git a/Documentation/devicetree/bindings/power/supply/cpcap-charger.yaml b/Documentation/devicetree/bindings/power/supply/cpcap-charger.yaml new file mode 100644 index 0000000..cb63536 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/cpcap-charger.yaml @@ -0,0 +1,106 @@ +# SPDX-License-Identifier: GPL-2.0 +# Copyright (C) 2021 Sebastian Reichel +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/cpcap-charger.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Motorola CPCAP PMIC charger + +maintainers: + - Tony Lindgren + - Sebastian Reichel + +description: | + Motorola CPCAP is a PMIC found in some mobile phones, e.g. + the Droid 4. This binding describes its battery charger + sub-function. + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: motorola,mapphone-cpcap-charger + + interrupts: + items: + - description: charger detection interrupt + - description: reverse charge interrupt + - description: SE1 charger detection interrupt + - description: SE0 charger detection interrupt + - description: reverse mode interrupt + - description: charge current 2 interrupt + - description: charge current 1 interrupt + - description: VBUS valid interrupt + - description: battery detect interrupt + + interrupt-names: + items: + - const: chrg_det + - const: rvrs_chrg + - const: chrg_se1b + - const: se0conn + - const: rvrs_mode + - const: chrgcurr2 + - const: chrgcurr1 + - const: vbusvld + - const: battdetb + + io-channels: + items: + - description: battery temperature + - description: battery voltage + - description: VBUS voltage + - description: battery charge current + - description: battery current + + io-channel-names: + items: + - const: battdetb + - const: battp + - const: vbus + - const: chg_isense + - const: batti + + mode-gpios: + description: | + Optionally CPCAP charger can have a companion wireless + charge controller that is controlled with two GPIOs + that are active low. + minItems: 2 + maxItems: 2 + +required: + - compatible + - interrupts + - interrupt-names + - io-channels + - io-channel-names + +additionalProperties: false + +examples: + - | + #include + cpcap { + charger { + compatible = "motorola,mapphone-cpcap-charger"; + interrupts-extended = + <&cpcap 13 0>, <&cpcap 12 0>, <&cpcap 29 0>, <&cpcap 28 0>, + <&cpcap 22 0>, <&cpcap 21 0>, <&cpcap 20 0>, <&cpcap 19 0>, + <&cpcap 54 0>; + interrupt-names = + "chrg_det", "rvrs_chrg", "chrg_se1b", "se0conn", + "rvrs_mode", "chrgcurr2", "chrgcurr1", "vbusvld", + "battdetb"; + mode-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>, + <&gpio3 23 GPIO_ACTIVE_LOW>; + io-channels = <&cpcap_adc 0>, <&cpcap_adc 1>, + <&cpcap_adc 2>, <&cpcap_adc 5>, + <&cpcap_adc 6>; + io-channel-names = "battdetb", "battp", + "vbus", "chg_isense", + "batti"; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/da9150-charger.txt b/Documentation/devicetree/bindings/power/supply/da9150-charger.txt deleted file mode 100644 index f390666..0000000 --- a/Documentation/devicetree/bindings/power/supply/da9150-charger.txt +++ /dev/null @@ -1,26 +0,0 @@ -Dialog Semiconductor DA9150 Charger Power Supply bindings - -Required properties: -- compatible: "dlg,da9150-charger" for DA9150 Charger Power Supply - -Optional properties: -- io-channels: List of phandle and IIO specifier pairs -- io-channel-names: List of channel names used by charger - ["CHAN_IBUS", "CHAN_VBUS", "CHAN_TJUNC", "CHAN_VBAT"] - (See Documentation/devicetree/bindings/iio/iio-bindings.txt for further info) - - -Example: - - da9150-charger { - compatible = "dlg,da9150-charger"; - - io-channels = <&gpadc 0>, - <&gpadc 2>, - <&gpadc 8>, - <&gpadc 5>; - io-channel-names = "CHAN_IBUS", - "CHAN_VBUS", - "CHAN_TJUNC", - "CHAN_VBAT"; - }; diff --git a/Documentation/devicetree/bindings/power/supply/da9150-fg.txt b/Documentation/devicetree/bindings/power/supply/da9150-fg.txt deleted file mode 100644 index 00236fe..0000000 --- a/Documentation/devicetree/bindings/power/supply/da9150-fg.txt +++ /dev/null @@ -1,23 +0,0 @@ -Dialog Semiconductor DA9150 Fuel-Gauge Power Supply bindings - -Required properties: -- compatible: "dlg,da9150-fuel-gauge" for DA9150 Fuel-Gauge Power Supply - -Optional properties: -- dlg,update-interval: Interval time (milliseconds) between battery level checks. -- dlg,warn-soc-level: Battery discharge level (%) where warning event raised. - [1 - 100] -- dlg,crit-soc-level: Battery discharge level (%) where critical event raised. - This value should be lower than the warning level. - [1 - 100] - - -Example: - - fuel-gauge { - compatible = "dlg,da9150-fuel-gauge"; - - dlg,update-interval = <10000>; - dlg,warn-soc-level = /bits/ 8 <15>; - dlg,crit-soc-level = /bits/ 8 <5>; - }; diff --git a/Documentation/devicetree/bindings/power/supply/dlg,da9150-charger.yaml b/Documentation/devicetree/bindings/power/supply/dlg,da9150-charger.yaml new file mode 100644 index 0000000..96336b0 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/dlg,da9150-charger.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/dlg,da9150-charger.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Dialog Semiconductor DA9150 Charger Power Supply bindings + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: dlg,da9150-charger + + io-channels: + items: + - description: ADC channel for current + - description: ADC channel for bus voltage + - description: ADC channel for junction temperature + - description: ADC channel for battery voltage + + io-channel-names: + items: + - const: CHAN_IBUS + - const: CHAN_VBUS + - const: CHAN_TJUNC + - const: CHAN_VBAT + +required: + - compatible + +additionalProperties: false + +examples: + - | + pmic { + charger { + compatible = "dlg,da9150-charger"; + io-channels = <&gpadc 0>, + <&gpadc 2>, + <&gpadc 8>, + <&gpadc 5>; + io-channel-names = "CHAN_IBUS", + "CHAN_VBUS", + "CHAN_TJUNC", + "CHAN_VBAT"; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/dlg,da9150-fuel-gauge.yaml b/Documentation/devicetree/bindings/power/supply/dlg,da9150-fuel-gauge.yaml new file mode 100644 index 0000000..30c2fff --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/dlg,da9150-fuel-gauge.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/dlg,da9150-fuel-gauge.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Dialog Semiconductor DA9150 Fuel-Gauge Power Supply bindings + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: dlg,da9150-fuel-gauge + + dlg,update-interval: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Interval time (milliseconds) between battery level checks. + + dlg,warn-soc-level: + $ref: /schemas/types.yaml#/definitions/uint8 + minimum: 1 + maximum: 100 + description: Battery discharge level (%) where warning event raised. + + dlg,crit-soc-level: + $ref: /schemas/types.yaml#/definitions/uint8 + minimum: 1 + maximum: 100 + description: | + Battery discharge level (%) where critical event raised. + This value should be lower than the warning level. + +required: + - compatible + +additionalProperties: false + +examples: + - | + pmic { + battery { + compatible = "dlg,da9150-fuel-gauge"; + dlg,update-interval = <10000>; + dlg,warn-soc-level = /bits/ 8 <15>; + dlg,crit-soc-level = /bits/ 8 <5>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/isp1704.txt b/Documentation/devicetree/bindings/power/supply/isp1704.txt deleted file mode 100644 index fa35969..0000000 --- a/Documentation/devicetree/bindings/power/supply/isp1704.txt +++ /dev/null @@ -1,17 +0,0 @@ -Binding for NXP ISP1704 USB Charger Detection - -Required properties: -- compatible: Should contain one of the following: - * "nxp,isp1704" -- nxp,enable-gpio: Should contain a phandle + gpio-specifier - to the GPIO pin connected to the chip's enable pin. -- usb-phy: Should contain a phandle to the USB PHY - the ISP1704 is connected to. - -Example: - -isp1704 { - compatible = "nxp,isp1704"; - nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_LOW>; - usb-phy = <&usb2_phy>; -}; diff --git a/Documentation/devicetree/bindings/power/supply/isp1704.yaml b/Documentation/devicetree/bindings/power/supply/isp1704.yaml new file mode 100644 index 0000000..4c91da7 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/isp1704.yaml @@ -0,0 +1,42 @@ +# SPDX-License-Identifier: GPL-2.0 +# Copyright (C) 2021 Sebastian Reichel +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/isp1704.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Binding for NXP ISP1704 USB Charger Detection + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: nxp,isp1704 + + nxp,enable-gpio: + maxItems: 1 + description: GPIO connected to the chip's enable pin + + usb-phy: + $ref: /schemas/types.yaml#/definitions/phandle + description: USB PHY the ISP1704 is connected to + +required: + - compatible + - nxp,enable-gpio + - usb-phy + +additionalProperties: false + +examples: + - | + #include + charger-detect { + compatible = "nxp,isp1704"; + nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_LOW>; + usb-phy = <&usb2_phy>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/lego,ev3-battery.yaml b/Documentation/devicetree/bindings/power/supply/lego,ev3-battery.yaml new file mode 100644 index 0000000..518eabb --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/lego,ev3-battery.yaml @@ -0,0 +1,55 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/lego,ev3-battery.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: LEGO MINDSTORMS EV3 Battery + +maintainers: + - David Lechner + - Sebastian Reichel + +description: | + LEGO MINDSTORMS EV3 has some built-in capability for monitoring the battery. + It uses 6 AA batteries or a special Li-ion rechargeable battery pack that is + detected by a key switch in the battery compartment. + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: lego,ev3-battery + + io-channels: + items: + - description: ADC channel for battery voltage + - description: ADC channel for battery current + + io-channel-names: + items: + - const: voltage + - const: current + + rechargeable-gpios: + maxItems: 1 + description: Rechargeable battery indication gpio + +required: + - compatible + - io-channels + - io-channel-names + - rechargeable-gpios + +additionalProperties: false + +examples: + - | + #include + battery { + compatible = "lego,ev3-battery"; + io-channels = <&adc 4>, <&adc 3>; + io-channel-names = "voltage", "current"; + rechargeable-gpios = <&gpio 136 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/lego_ev3_battery.txt b/Documentation/devicetree/bindings/power/supply/lego_ev3_battery.txt deleted file mode 100644 index 5485633..0000000 --- a/Documentation/devicetree/bindings/power/supply/lego_ev3_battery.txt +++ /dev/null @@ -1,21 +0,0 @@ -LEGO MINDSTORMS EV3 Battery -~~~~~~~~~~~~~~~~~~~~~~~~~~~ - -LEGO MINDSTORMS EV3 has some built-in capability for monitoring the battery. -It uses 6 AA batteries or a special Li-ion rechargeable battery pack that is -detected by a key switch in the battery compartment. - -Required properties: - - compatible: Must be "lego,ev3-battery" - - io-channels: phandles to analog inputs for reading voltage and current - - io-channel-names: Must be "voltage", "current" - - rechargeable-gpios: phandle to the rechargeable battery indication gpio - -Example: - - battery { - compatible = "lego,ev3-battery"; - io-channels = <&adc 4>, <&adc 3>; - io-channel-names = "voltage", "current"; - rechargeable-gpios = <&gpio 136 GPIO_ACTIVE_LOW>; - }; diff --git a/Documentation/devicetree/bindings/power/supply/lltc,lt3651-charger.yaml b/Documentation/devicetree/bindings/power/supply/lltc,lt3651-charger.yaml new file mode 100644 index 0000000..e2d8d2a --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/lltc,lt3651-charger.yaml @@ -0,0 +1,44 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/lltc,lt3651-charger.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Analog Devices LT3651 Charger Power Supply bindings + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + enum: + - lltc,lt3651-charger + - lltc,ltc3651-charger # deprecated, use lltc,lt3651-charger + + lltc,acpr-gpios: + maxItems: 1 + + lltc,fault-gpios: + maxItems: 1 + + lltc,chrg-gpios: + maxItems: 1 + +required: + - compatible + - lltc,acpr-gpios + +additionalProperties: false + +examples: + - | + #include + charger { + compatible = "lltc,lt3651-charger"; + lltc,acpr-gpios = <&gpio0 68 GPIO_ACTIVE_LOW>; + lltc,fault-gpios = <&gpio0 64 GPIO_ACTIVE_LOW>; + lltc,chrg-gpios = <&gpio0 63 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/lltc,ltc294x.yaml b/Documentation/devicetree/bindings/power/supply/lltc,ltc294x.yaml new file mode 100644 index 0000000..043bf37 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/lltc,ltc294x.yaml @@ -0,0 +1,66 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/lltc,ltc294x.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Binding for LTC2941, LTC2942, LTC2943 and LTC2944 battery fuel gauges + +description: | + All chips measure battery capacity. + The LTC2942 is pin compatible with the LTC2941, it adds voltage and + temperature monitoring, and is runtime detected. LTC2943 and LTC2944 + are software compatible, uses a slightly different conversion formula + for the charge counter and adds voltage, current and temperature monitoring. + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + enum: + - lltc,ltc2941 + - lltc,ltc2942 + - lltc,ltc2943 + - lltc,ltc2944 + + reg: + maxItems: 1 + + lltc,resistor-sense: + $ref: /schemas/types.yaml#/definitions/int32 + description: | + Sense resistor value in milli-ohms. + Can be negative value when the battery has been connected to the wrong end of the resistor. + + lltc,prescaler-exponent: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + The prescaler exponent as explained in the datasheet. + This determines the range and accuracy of the gauge. + The value is programmed into the chip only if it differs from the current setting. + The setting is lost when the battery is disconnected. + +required: + - compatible + - reg + - lltc,resistor-sense + - lltc,prescaler-exponent + +additionalProperties: false + +examples: + - | + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + battery@64 { + compatible = "lltc,ltc2943"; + reg = <0x64>; + lltc,resistor-sense = <15>; + lltc,prescaler-exponent = <5>; /* 2^(2*5) = 1024 */ + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt b/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt deleted file mode 100644 index 0355a4b..0000000 --- a/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt +++ /dev/null @@ -1,43 +0,0 @@ -Binding for TI/National Semiconductor LP8727 Charger - -Required properties: -- compatible: "ti,lp8727" -- reg: I2C slave address 27h - -Optional properties: -- interrupts: interrupt specifier (see interrupt binding[0]) -- debounce-ms: interrupt debounce time. (u32) - -AC and USB charging parameters -- charger-type: "ac" or "usb" (string) -- eoc-level: value of 'enum lp8727_eoc_level' (u8) -- charging-current: value of 'enum lp8727_ichg' (u8) - -[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - -Example) - -lp8727@27 { - compatible = "ti,lp8727"; - reg = <0x27>; - - /* GPIO 134 is used for LP8728 interrupt pin */ - interrupt-parent = <&gpio5>; /* base = 128 */ - interrupts = <6 0x2>; /* offset = 6, falling edge type */ - - debounce-ms = <300>; - - /* AC charger: 5% EOC and 500mA charging current */ - ac { - charger-type = "ac"; - eoc-level = /bits/ 8 <0>; - charging-current = /bits/ 8 <4>; - }; - - /* USB charger: 10% EOC and 400mA charging current */ - usb { - charger-type = "usb"; - eoc-level = /bits/ 8 <1>; - charging-current = /bits/ 8 <2>; - }; -}; diff --git a/Documentation/devicetree/bindings/power/supply/lt3651-charger.txt b/Documentation/devicetree/bindings/power/supply/lt3651-charger.txt deleted file mode 100644 index 40811ff..0000000 --- a/Documentation/devicetree/bindings/power/supply/lt3651-charger.txt +++ /dev/null @@ -1,29 +0,0 @@ -Analog Devices LT3651 Charger Power Supply bindings: lt3651-charger - -Required properties: -- compatible: Should contain one of the following: - * "lltc,ltc3651-charger", (DEPRECATED: Use "lltc,lt3651-charger") - * "lltc,lt3651-charger" - - lltc,acpr-gpios: Connect to ACPR output. See remark below. - -Optional properties: - - lltc,fault-gpios: Connect to FAULT output. See remark below. - - lltc,chrg-gpios: Connect to CHRG output. See remark below. - -The lt3651 outputs are open-drain type and active low. The driver assumes the -GPIO reports "active" when the output is asserted, so if the pins have been -connected directly, the GPIO flags should be set to active low also. - -The driver will attempt to aquire interrupts for all GPIOs to detect changes in -line state. If the system is not capabale of providing interrupts, the driver -cannot report changes and userspace will need to periodically read the sysfs -attributes to detect changes. - -Example: - - charger: battery-charger { - compatible = "lltc,lt3651-charger"; - lltc,acpr-gpios = <&gpio0 68 GPIO_ACTIVE_LOW>; - lltc,fault-gpios = <&gpio0 64 GPIO_ACTIVE_LOW>; - lltc,chrg-gpios = <&gpio0 63 GPIO_ACTIVE_LOW>; - }; diff --git a/Documentation/devicetree/bindings/power/supply/ltc2941.txt b/Documentation/devicetree/bindings/power/supply/ltc2941.txt deleted file mode 100644 index 3b9ba14..0000000 --- a/Documentation/devicetree/bindings/power/supply/ltc2941.txt +++ /dev/null @@ -1,28 +0,0 @@ -binding for LTC2941, LTC2942, LTC2943 and LTC2944 battery gauges - -All chips measure battery capacity. -The LTC2942 is pin compatible with the LTC2941, it adds voltage and -temperature monitoring, and is runtime detected. LTC2943 and LTC2944 -is software compatible, uses a slightly different conversion formula -for the charge counter and adds voltage, current and temperature monitoring. - -Required properties: -- compatible: Should contain "lltc,ltc2941", "lltc,ltc2942", "lltc,ltc2943" - or "lltc,ltc2944" which also indicates the type of I2C chip attached. -- reg: The 7-bit I2C address. -- lltc,resistor-sense: The sense resistor value in milli-ohms. Can be a 32-bit - negative value when the battery has been connected to the wrong end of the - resistor. -- lltc,prescaler-exponent: The prescaler exponent as explained in the datasheet. - This determines the range and accuracy of the gauge. The value is programmed - into the chip only if it differs from the current setting. The setting is - lost when the battery is disconnected. - -Example from the Topic Miami Florida board: - - fuelgauge: ltc2943@64 { - compatible = "lltc,ltc2943"; - reg = <0x64>; - lltc,resistor-sense = <15>; - lltc,prescaler-exponent = <5>; /* 2^(2*5) = 1024 */ - }; diff --git a/Documentation/devicetree/bindings/power/supply/max17040_battery.txt b/Documentation/devicetree/bindings/power/supply/max17040_battery.txt deleted file mode 100644 index c802f66..0000000 --- a/Documentation/devicetree/bindings/power/supply/max17040_battery.txt +++ /dev/null @@ -1,52 +0,0 @@ -max17040_battery -~~~~~~~~~~~~~~~~ - -Required properties : - - compatible : "maxim,max17040", "maxim,max17041", "maxim,max17043", - "maxim,max17044", "maxim,max17048", "maxim,max17049", - "maxim,max17058", "maxim,max17059" or "maxim,max77836-battery" - - reg: i2c slave address - -Optional properties : -- maxim,alert-low-soc-level : The alert threshold that sets the state of - charge level (%) where an interrupt is - generated. Can be configured from 1 up to 32 - (%). If skipped the power up default value of - 4 (%) will be used. -- maxim,double-soc : Certain devices return double the capacity. - Specify this boolean property to divide the - reported value in 2 and thus normalize it. - SOC == State of Charge == Capacity. -- maxim,rcomp : A value to compensate readings for various - battery chemistries and operating temperatures. - max17040,41 have 2 byte rcomp, default to - 0x97 0x00. All other devices have one byte - rcomp, default to 0x97. -- interrupts : Interrupt line see Documentation/devicetree/ - bindings/interrupt-controller/interrupts.txt -- wakeup-source : This device has wakeup capabilities. Use this - property to use alert low SOC level interrupt - as wake up source. - -Optional properties support interrupt functionality for alert low state of -charge level, present in some ICs in the same family, and should be used with -compatible "maxim,max77836-battery". - -Example: - - battery-fuel-gauge@36 { - compatible = "maxim,max77836-battery"; - reg = <0x36>; - maxim,alert-low-soc-level = <10>; - interrupt-parent = <&gpio7>; - interrupts = <2 IRQ_TYPE_EDGE_FALLING>; - wakeup-source; - }; - - battery-fuel-gauge@36 { - compatible = "maxim,max17048"; - reg = <0x36>; - maxim,rcomp = /bits/ 8 <0x56>; - maxim,alert-low-soc-level = <10>; - maxim,double-soc; - }; diff --git a/Documentation/devicetree/bindings/power/supply/max17042_battery.txt b/Documentation/devicetree/bindings/power/supply/max17042_battery.txt deleted file mode 100644 index f34c5da..0000000 --- a/Documentation/devicetree/bindings/power/supply/max17042_battery.txt +++ /dev/null @@ -1,35 +0,0 @@ -max17042_battery -~~~~~~~~~~~~~~~~ - -Required properties : - - compatible : one of the following - * "maxim,max17042" - * "maxim,max17047" - * "maxim,max17050" - * "maxim,max17055" - -Optional properties : - - maxim,rsns-microohm : Resistance of rsns resistor in micro Ohms - (datasheet-recommended value is 10000). - Defining this property enables current-sense functionality. - -Optional threshold properties : - If skipped the condition won't be reported. - - maxim,cold-temp : Temperature threshold to report battery - as cold (in tenths of degree Celsius). - - maxim,over-heat-temp : Temperature threshold to report battery - as over heated (in tenths of degree Celsius). - - maxim,dead-volt : Voltage threshold to report battery - as dead (in mV). - - maxim,over-volt : Voltage threshold to report battery - as over voltage (in mV). - -Example: - - battery-charger@36 { - compatible = "maxim,max17042"; - reg = <0x36>; - maxim,rsns-microohm = <10000>; - maxim,over-heat-temp = <600>; - maxim,over-volt = <4300>; - }; diff --git a/Documentation/devicetree/bindings/power/supply/max8903-charger.txt b/Documentation/devicetree/bindings/power/supply/max8903-charger.txt deleted file mode 100644 index bab947f..0000000 --- a/Documentation/devicetree/bindings/power/supply/max8903-charger.txt +++ /dev/null @@ -1,24 +0,0 @@ -Maxim Semiconductor MAX8903 Battery Charger bindings - -Required properties: -- compatible: "maxim,max8903" for MAX8903 Battery Charger -- dok-gpios: Valid DC power has been detected (active low, input), optional if uok-gpios is provided -- uok-gpios: Valid USB power has been detected (active low, input), optional if dok-gpios is provided - -Optional properties: -- cen-gpios: Charge enable pin (active low, output) -- chg-gpios: Charger status pin (active low, input) -- flt-gpios: Fault pin (active low, output) -- dcm-gpios: Current limit mode setting (DC=1 or USB=0, output) -- usus-gpios: USB suspend pin (active high, output) - - -Example: - - max8903-charger { - compatible = "maxim,max8903"; - dok-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; - flt-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; - chg-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; - cen-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; - }; diff --git a/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt b/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt deleted file mode 100644 index 55967a0..0000000 --- a/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt +++ /dev/null @@ -1,26 +0,0 @@ -Devicetree bindings for Maxim DS2760 -==================================== - -The ds2760 is a w1 slave device and must hence have its sub-node in DT -under a w1 bus master node. - -The device exposes a power supply, so the details described in -Documentation/devicetree/bindings/power/supply/power_supply.txt apply. - -Required properties: -- compatible: must be "maxim,ds2760" - -Optional properties: -- power-supplies: Refers to one or more power supplies connected to - this battery. -- maxim,pmod-enabled: This boolean property enables the DS2760 to enter - sleep mode when the DQ line goes low for greater - than 2 seconds and leave sleep Mode when the DQ - line goes high. -- maxim,cache-time-ms: Time im milliseconds to cache the data for. When - this time expires, the values are read again from - the hardware. Defaults to 1000. -- rated-capacity-microamp-hours: - The rated capacity of the battery, in mAh. - If not specified, the value stored in the - non-volatile chip memory is used. diff --git a/Documentation/devicetree/bindings/power/supply/maxim,ds2760.yaml b/Documentation/devicetree/bindings/power/supply/maxim,ds2760.yaml new file mode 100644 index 0000000..818647e --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/maxim,ds2760.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/maxim,ds2760.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Maxim DS2760 DT bindings + +maintainers: + - Sebastian Reichel + +description: | + The ds2760 is a w1 slave device and must hence have its sub-node in + DT under a w1 bus master node. + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: maxim,ds2760 + + maxim,pmod-enabled: + description: | + Allow the DS2760 to enter sleep mode when the DQ line goes low for more than 2 seconds + and leave sleep Mode when the DQ line goes high. + type: boolean + + maxim,cache-time-ms: + description: | + Time im milliseconds to cache the data for. + When this time expires, the values are read again from the hardware. + Defaults to 1000. + + rated-capacity-microamp-hours: + description: | + The rated capacity of the battery, in mAh. + If not specified, the value stored in the non-volatile chip memory is used. + +required: + - compatible + +unevaluatedProperties: false diff --git a/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt b/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt deleted file mode 100644 index f956247..0000000 --- a/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt +++ /dev/null @@ -1,23 +0,0 @@ -Maxim MAX14656 / AL32 USB Charger Detector - -Required properties : -- compatible : "maxim,max14656"; -- reg: i2c slave address -- interrupts: interrupt line - -Example: - -&i2c2 { - clock-frequency = <50000>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c2>; - - max14656@35 { - compatible = "maxim,max14656"; - reg = <0x35>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_charger_detect>; - interrupt-parent = <&gpio6>; - interrupts = <26 IRQ_TYPE_LEVEL_HIGH>; - }; -}; diff --git a/Documentation/devicetree/bindings/power/supply/maxim,max14656.yaml b/Documentation/devicetree/bindings/power/supply/maxim,max14656.yaml new file mode 100644 index 0000000..0a41078 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/maxim,max14656.yaml @@ -0,0 +1,45 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/maxim,max14656.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Maxim MAX14656 DT bindings + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: maxim,max14656 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + #include + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + charger-detector@35 { + compatible = "maxim,max14656"; + reg = <0x35>; + interrupt-parent = <&gpio6>; + interrupts = <26 IRQ_TYPE_LEVEL_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/maxim,max17040.yaml b/Documentation/devicetree/bindings/power/supply/maxim,max17040.yaml new file mode 100644 index 0000000..de91cf3 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/maxim,max17040.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/maxim,max17040.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Maxim 17040 fuel gauge series + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + enum: + - maxim,max17040 + - maxim,max17041 + - maxim,max17043 + - maxim,max17044 + - maxim,max17048 + - maxim,max17049 + - maxim,max17058 + - maxim,max17059 + - maxim,max77836-battery + + reg: + maxItems: 1 + + maxim,alert-low-soc-level: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 32 + description: | + The alert threshold that sets the state of charge level (%) where an interrupt is generated. + If skipped the power up default value of 4 (%) will be used. + + maxim,double-soc: + type: boolean + description: | + Certain devices return double the capacity. + Specify this to divide the reported value in 2 and thus normalize it. + SoC == State of Charge == Capacity. + + maxim,rcomp: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + A value to compensate readings for various battery chemistries and operating temperatures. + max17040,41 have 2 byte rcomp, default to 0x97 0x00. + All other devices have one byte rcomp, default to 0x97. + + interrupts: + maxItems: 1 + + wakeup-source: + type: boolean + description: | + Use this property to use alert low SoC level interrupt as wake up source. + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + battery@36 { + compatible = "maxim,max17048"; + reg = <0x36>; + maxim,rcomp = /bits/ 8 <0x56>; + maxim,alert-low-soc-level = <10>; + maxim,double-soc; + }; + }; + - | + #include + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + battery@36 { + compatible = "maxim,max77836-battery"; + reg = <0x36>; + maxim,alert-low-soc-level = <10>; + interrupt-parent = <&gpio7>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/maxim,max17042.yaml b/Documentation/devicetree/bindings/power/supply/maxim,max17042.yaml new file mode 100644 index 0000000..c70f05e --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/maxim,max17042.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/maxim,max17042.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Maxim 17042 fuel gauge series + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + enum: + - maxim,max17042 + - maxim,max17047 + - maxim,max17050 + - maxim,max17055 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + maxim,rsns-microohm: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Resistance of rsns resistor in micro Ohms (datasheet-recommended value is 10000). + Defining this property enables current-sense functionality. + + maxim,cold-temp: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Temperature threshold to report battery as cold (in tenths of degree Celsius). + Default is not to report cold events. + + maxim,over-heat-temp: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Temperature threshold to report battery as over heated (in tenths of degree Celsius). + Default is not to report over heating events. + + maxim,dead-volt: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Voltage threshold to report battery as dead (in mV). + Default is not to report dead battery events. + + maxim,over-volt: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Voltage threshold to report battery as over voltage (in mV). + Default is not to report over-voltage events. + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + battery@36 { + compatible = "maxim,max17042"; + reg = <0x36>; + maxim,rsns-microohm = <10000>; + maxim,over-heat-temp = <600>; + maxim,over-volt = <4300>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/maxim,max8903.yaml b/Documentation/devicetree/bindings/power/supply/maxim,max8903.yaml new file mode 100644 index 0000000..4828ca0 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/maxim,max8903.yaml @@ -0,0 +1,67 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/maxim,max8903.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Maxim Semiconductor MAX8903 Battery Charger + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: maxim,max8903 + + dok-gpios: + maxItems: 1 + description: Valid DC power has been detected (active low, input) + + uok-gpios: + maxItems: 1 + description: Valid USB power has been detected (active low, input) + + cen-gpios: + maxItems: 1 + description: Charge enable pin (active low, output) + + chg-gpios: + maxItems: 1 + description: Charger status pin (active low, input) + + flt-gpios: + maxItems: 1 + description: Fault pin (active low, output) + + dcm-gpios: + maxItems: 1 + description: Current limit mode setting (DC=1 or USB=0, output) + + usus-gpios: + maxItems: 1 + description: USB suspend pin (active high, output) + +required: + - compatible + +anyOf: + - required: + - dok-gpios + - required: + - uok-gpios + +additionalProperties: false + +examples: + - | + #include + charger { + compatible = "maxim,max8903"; + dok-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; + flt-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; + chg-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; + cen-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/microchip,ucs1002.txt b/Documentation/devicetree/bindings/power/supply/microchip,ucs1002.txt deleted file mode 100644 index 1d284ad..0000000 --- a/Documentation/devicetree/bindings/power/supply/microchip,ucs1002.txt +++ /dev/null @@ -1,27 +0,0 @@ -Microchip UCS1002 USB Port Power Controller - -Required properties: -- compatible : Should be "microchip,ucs1002"; -- reg : I2C slave address - -Optional properties: -- interrupts : A list of interrupts lines present (could be either - corresponding to A_DET# pin, ALERT# pin, or both) -- interrupt-names : A list of interrupt names. Should contain (if - present): - - "a_det" for line connected to A_DET# pin - - "alert" for line connected to ALERT# pin - Both are expected to be IRQ_TYPE_EDGE_BOTH -Example: - -&i2c3 { - charger@32 { - compatible = "microchip,ucs1002"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ucs1002_pins>; - reg = <0x32>; - interrupts-extended = <&gpio5 2 IRQ_TYPE_EDGE_BOTH>, - <&gpio3 21 IRQ_TYPE_EDGE_BOTH>; - interrupt-names = "a_det", "alert"; - }; -}; diff --git a/Documentation/devicetree/bindings/power/supply/microchip,ucs1002.yaml b/Documentation/devicetree/bindings/power/supply/microchip,ucs1002.yaml new file mode 100644 index 0000000..b9bd159 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/microchip,ucs1002.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/supply/microchip,ucs1002.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip UCS1002 USB Port Power Controller + +maintainers: + - Sebastian Reichel + +properties: + compatible: + const: microchip,ucs1002 + + reg: + maxItems: 1 + + interrupts: + maxItems: 2 + + interrupt-names: + oneOf: + - items: + - const: a_det + - const: alert + - const: a_det + - const: alert + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + charger@32 { + compatible = "microchip,ucs1002"; + reg = <0x32>; + interrupts-extended = <&gpio5 2 IRQ_TYPE_EDGE_BOTH>, + <&gpio3 21 IRQ_TYPE_EDGE_BOTH>; + interrupt-names = "a_det", "alert"; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/nokia,n900-battery.yaml b/Documentation/devicetree/bindings/power/supply/nokia,n900-battery.yaml new file mode 100644 index 0000000..4a1489f --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/nokia,n900-battery.yaml @@ -0,0 +1,49 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/nokia,n900-battery.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Nokia N900 battery + +maintainers: + - Pali Rohár + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: nokia,n900-battery + + io-channels: + items: + - description: ADC channel for temperature reading + - description: ADC channel for battery size identification + - description: ADC channel to measure the battery voltage + + io-channel-names: + items: + - const: temp + - const: bsi + - const: vbat + +required: + - compatible + - io-channels + - io-channel-names + +additionalProperties: false + +examples: + - | + battery { + compatible = "nokia,n900-battery"; + io-channels = <&twl4030_madc 0>, + <&twl4030_madc 4>, + <&twl4030_madc 12>; + io-channel-names = "temp", + "bsi", + "vbat"; + }; diff --git a/Documentation/devicetree/bindings/power/supply/olpc-battery.yaml b/Documentation/devicetree/bindings/power/supply/olpc-battery.yaml new file mode 100644 index 0000000..0bd7bf3 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/olpc-battery.yaml @@ -0,0 +1,27 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/olpc-battery.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: OLPC Battery + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + oneOf: + - items: + - const: olpc,xo1.5-battery + - const: olpc,xo1-battery + - items: + - const: olpc,xo1-battery + +required: + - compatible + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/power/supply/olpc_battery.txt b/Documentation/devicetree/bindings/power/supply/olpc_battery.txt deleted file mode 100644 index 8d87d6b..0000000 --- a/Documentation/devicetree/bindings/power/supply/olpc_battery.txt +++ /dev/null @@ -1,5 +0,0 @@ -OLPC battery -~~~~~~~~~~~~ - -Required properties: - - compatible : "olpc,xo1-battery" or "olpc,xo1.5-battery" diff --git a/Documentation/devicetree/bindings/power/supply/power_supply.txt b/Documentation/devicetree/bindings/power/supply/power_supply.txt deleted file mode 100644 index d9693e0..0000000 --- a/Documentation/devicetree/bindings/power/supply/power_supply.txt +++ /dev/null @@ -1,2 +0,0 @@ -This binding has been converted to yaml please see power-supply.yaml in this -directory. diff --git a/Documentation/devicetree/bindings/power/supply/qcom,coincell-charger.txt b/Documentation/devicetree/bindings/power/supply/qcom,coincell-charger.txt deleted file mode 100644 index 7478992..0000000 --- a/Documentation/devicetree/bindings/power/supply/qcom,coincell-charger.txt +++ /dev/null @@ -1,48 +0,0 @@ -Qualcomm Coincell Charger: - -The hardware block controls charging for a coincell or capacitor that is -used to provide power backup for certain features of the power management -IC (PMIC) - -- compatible: - Usage: required - Value type: - Definition: must be: "qcom,pm8941-coincell" - -- reg: - Usage: required - Value type: - Definition: base address of the coincell charger registers - -- qcom,rset-ohms: - Usage: required - Value type: - Definition: resistance (in ohms) for current-limiting resistor - must be one of: 800, 1200, 1700, 2100 - -- qcom,vset-millivolts: - Usage: required - Value type: - Definition: voltage (in millivolts) to apply for charging - must be one of: 2500, 3000, 3100, 3200 - -- qcom,charger-disable: - Usage: optional - Value type: - Definition: defining this property disables charging - -This charger is a sub-node of one of the 8941 PMIC blocks, and is specified -as a child node in DTS of that node. See ../mfd/qcom,spmi-pmic.txt and -../mfd/qcom-pm8xxx.txt - -Example: - - pm8941@0 { - coincell@2800 { - compatible = "qcom,pm8941-coincell"; - reg = <0x2800>; - - qcom,rset-ohms = <2100>; - qcom,vset-millivolts = <3000>; - }; - }; diff --git a/Documentation/devicetree/bindings/power/supply/qcom,pm8941-charger.yaml b/Documentation/devicetree/bindings/power/supply/qcom,pm8941-charger.yaml new file mode 100644 index 0000000..bc89048 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/qcom,pm8941-charger.yaml @@ -0,0 +1,169 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/supply/qcom,pm8941-charger.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Switch-Mode Battery Charger and Boost + +maintainers: + - Sebastian Reichel + +properties: + compatible: + const: qcom,pm8941-charger + + reg: + maxItems: 1 + + interrupts: + items: + - description: charge done + - description: charge fast mode + - description: charge trickle mode + - description: battery temperature ok + - description: battery present + - description: charger disconnected + - description: USB-in valid + - description: DC-in valid + + interrupt-names: + items: + - const: chg-done + - const: chg-fast + - const: chg-trkl + - const: bat-temp-ok + - const: bat-present + - const: chg-gone + - const: usb-valid + - const: dc-valid + + qcom,fast-charge-current-limit: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 100000 + maximum: 3000000 + description: Maximum charge current in uA; May be clamped to safety limits; Defaults to 1A + + qcom,fast-charge-low-threshold-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 2100000 + maximum: 3600000 + description: | + Battery voltage limit in uV above which fast charging may operate; Defaults to 3.2V + Below this value linear or switch-mode auto-trickle-charging will operate. + + qcom,fast-charge-high-threshold-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 3240000 + maximum: 5000000 + description: | + Battery voltage limit in uV below which fast charging may operate; Defaults to 4.2V + The fast charger will attempt to charge the battery to this voltage. + May be clamped to safety limits. + + qcom,fast-charge-safe-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 3240000 + maximum: 5000000 + description: | + Maximum safe battery voltage in uV; May be pre-set by bootloader, in which case, + setting this will harmlessly fail. The property 'fast-charge-high-watermark' will + be clamped by this value. Defaults to 4.2V. + + qcom,fast-charge-safe-current: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 100000 + maximum: 3000000 + description: | + Maximum safe battery charge current in uA; May pre-set by bootloader, in which case, + setting this will harmlessly fail. The property 'qcom,fast-charge-current-limit' + will be clamped by this value. Defaults to 1A. + + qcom,auto-recharge-threshold-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 3240000 + maximum: 5000000 + description: | + Battery voltage limit in uV below which auto-recharge functionality will restart charging + after end-of-charge; The high cutoff limit for auto-recharge is 5% above this value. + Defaults to 4.1V. + + qcom,minimum-input-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 4200000 + maximum: 9600000 + description: | + Input voltage level in uV above which charging may operate. Defaults to 4.3V. + + qcom,dc-current-limit: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 100000 + maximum: 2500000 + description: | + Default DC charge current limit in uA. Defaults to 100mA. + + qcom,disable-dc: + type: boolean + description: Disable DC charger + + qcom,jeita-extended-temp-range: + type: boolean + description: | + Enable JEITA extended temperature range; This does *not* adjust the maximum charge + voltage or current in the extended temperature range. It only allows charging when + the battery is in the extended temperature range. Voltage/current regulation must + be done externally to fully comply with the JEITA safety guidelines if this flag + is set. + + usb-otg-in-supply: + description: Reference to the regulator supplying power to the USB_OTG_IN pin. + + otg-vbus: + type: object + description: | + This node defines a regulator used to control the direction of VBUS voltage. + Specifically whether to supply voltage to VBUS for host mode operation of the OTG port, + or allow input voltage from external VBUS for charging. In the hardware, the supply for + this regulator comes from usb_otg_in-supply. + +required: + - compatible + - reg + - interrupts + - interrupt-names + +additionalProperties: false + +examples: + - | + #include + pmic { + #address-cells = <1>; + #size-cells = <0>; + + charger@1000 { + compatible = "qcom,pm8941-charger"; + reg = <0x1000>; + interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>; + interrupt-names = "chg-done", + "chg-fast", + "chg-trkl", + "bat-temp-ok", + "bat-present", + "chg-gone", + "usb-valid", + "dc-valid"; + qcom,fast-charge-current-limit = <1000000>; + qcom,dc-current-limit = <1000000>; + usb-otg-in-supply = <&pm8941_5vs1>; + + otg-vbus {}; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/qcom,pm8941-coincell.yaml b/Documentation/devicetree/bindings/power/supply/qcom,pm8941-coincell.yaml new file mode 100644 index 0000000..0450f4d --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/qcom,pm8941-coincell.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/supply/qcom,pm8941-coincell.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Coincell Charger + +description: | + The hardware block controls charging for a coincell or capacitor that is + used to provide power backup for certain features of the power management + IC (PMIC) + +maintainers: + - Sebastian Reichel + +properties: + compatible: + const: qcom,pm8941-coincell + + reg: + maxItems: 1 + + qcom,rset-ohms: + description: resistance (in ohms) for current-limiting resistor + enum: [ 800, 1200, 1700, 2100 ] + + qcom,vset-millivolts: + $ref: /schemas/types.yaml#/definitions/uint32 + description: voltage (in millivolts) to apply for charging + enum: [ 2500, 3000, 3100, 3200 ] + + qcom,charger-disable: + type: boolean + description: defining this property disables charging + +required: + - compatible + - reg + - qcom,rset-ohms + - qcom,vset-millivolts + +additionalProperties: false + +examples: + - | + pmic { + #address-cells = <1>; + #size-cells = <0>; + + charger@2800 { + compatible = "qcom,pm8941-coincell"; + reg = <0x2800>; + qcom,rset-ohms = <2100>; + qcom,vset-millivolts = <3000>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt b/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt deleted file mode 100644 index 06f8a5d..0000000 --- a/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt +++ /dev/null @@ -1,150 +0,0 @@ -Qualcomm Switch-Mode Battery Charger and Boost - -PROPERTIES -- compatible: - Usage: required - Value type: - Description: Must be one of: - - "qcom,pm8941-charger" - -- reg: - Usage: required - Value type: - Description: Base address of registers for SMBB block - -- interrupts: - Usage: required - Value type: - Description: The format of the specifier is defined by the binding document - describing the node's interrupt parent. Must contain one - specifier for each of the following interrupts, in order: - - charge done - - charge fast mode - - charge trickle mode - - battery temperature ok - - battery present - - charger disconnected - - USB-in valid - - DC-in valid - -- interrupt-names: - Usage: required - Value type: - Description: Must contain the following list, strictly ordered: - "chg-done", - "chg-fast", - "chg-trkl", - "bat-temp-ok", - "bat-present", - "chg-gone", - "usb-valid", - "dc-valid" - -- qcom,fast-charge-current-limit: - Usage: optional (default: 1A, or pre-configured value) - Value type: ; uA; range [100mA : 3A] - Description: Maximum charge current; May be clamped to safety limits. - -- qcom,fast-charge-low-threshold-voltage: - Usage: optional (default: 3.2V, or pre-configured value) - Value type: ; uV; range [2.1V : 3.6V] - Description: Battery voltage limit above which fast charging may operate; - Below this value linear or switch-mode auto-trickle-charging - will operate. - -- qcom,fast-charge-high-threshold-voltage: - Usage: optional (default: 4.2V, or pre-configured value) - Value type: ; uV; range [3.24V : 5V] - Description: Battery voltage limit below which fast charging may operate; - The fast charger will attempt to charge the battery to this - voltage. May be clamped to safety limits. - -- qcom,fast-charge-safe-voltage: - Usage: optional (default: 4.2V, or pre-configured value) - Value type: ; uV; range [3.24V : 5V] - Description: Maximum safe battery voltage; May be pre-set by bootloader, in - which case, setting this will harmlessly fail. The property - 'fast-charge-high-watermark' will be clamped by this value. - -- qcom,fast-charge-safe-current: - Usage: optional (default: 1A, or pre-configured value) - Value type: ; uA; range [100mA : 3A] - Description: Maximum safe battery charge current; May pre-set by bootloader, - in which case, setting this will harmlessly fail. The property - 'qcom,fast-charge-current-limit' will be clamped by this value. - -- qcom,auto-recharge-threshold-voltage: - Usage: optional (default: 4.1V, or pre-configured value) - Value type: ; uV; range [3.24V : 5V] - Description: Battery voltage limit below which auto-recharge functionality - will restart charging after end-of-charge; The high cutoff - limit for auto-recharge is 5% above this value. - -- qcom,minimum-input-voltage: - Usage: optional (default: 4.3V, or pre-configured value) - Value type: ; uV; range [4.2V : 9.6V] - Description: Input voltage level above which charging may operate - -- qcom,dc-current-limit: - Usage: optional (default: 100mA, or pre-configured value) - Value type: ; uA; range [100mA : 2.5A] - Description: Default DC charge current limit - -- qcom,disable-dc: - Usage: optional (default: false) - Value type: boolean: or - Description: Disable DC charger - -- qcom,jeita-extended-temp-range: - Usage: optional (default: false) - Value type: boolean: or - Description: Enable JEITA extended temperature range; This does *not* - adjust the maximum charge voltage or current in the extended - temperature range. It only allows charging when the battery - is in the extended temperature range. Voltage/current - regulation must be done externally to fully comply with - the JEITA safety guidelines if this flag is set. - -- usb_otg_in-supply: - Usage: optional - Value type: - Description: Reference to the regulator supplying power to the USB_OTG_IN - pin. - -child nodes: -- otg-vbus: - Usage: optional - Description: This node defines a regulator used to control the direction - of VBUS voltage - specifically: whether to supply voltage - to VBUS for host mode operation of the OTG port, or allow - input voltage from external VBUS for charging. In the - hardware, the supply for this regulator comes from - usb_otg_in-supply. - -EXAMPLE -charger@1000 { - compatible = "qcom,pm8941-charger"; - reg = <0x1000 0x700>; - interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>, - <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>, - <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>, - <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>, - <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>, - <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>, - <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>, - <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>; - interrupt-names = "chg-done", - "chg-fast", - "chg-trkl", - "bat-temp-ok", - "bat-present", - "chg-gone", - "usb-valid", - "dc-valid"; - - qcom,fast-charge-current-limit = <1000000>; - qcom,dc-charge-current-limit = <1000000>; - usb_otg_in-supply = <&pm8941_5vs1>; - - otg-vbus {}; -}; diff --git a/Documentation/devicetree/bindings/power/supply/richtek,rt9455.yaml b/Documentation/devicetree/bindings/power/supply/richtek,rt9455.yaml new file mode 100644 index 0000000..e1c2334 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/richtek,rt9455.yaml @@ -0,0 +1,90 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/richtek,rt9455.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Binding for Richtek rt9455 battery charger + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: richtek,rt9455 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + richtek,output-charge-current: + $ref: /schemas/types.yaml#/definitions/uint32 + description: output current from the charger to the battery, in uA. + + richtek,end-of-charge-percentage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + percent of the output charge current. When the current in constant-voltage phase drops + below output_charge_current x end-of-charge-percentage, charge is terminated. + + richtek,battery-regulation-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: maximum battery voltage in uV. + + richtek,boost-output-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + maximum voltage provided to consumer devices, when the charger is in boost mode, in uV. + + richtek,min-input-voltage-regulation: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + input voltage level in uV, used to decrease voltage level when the over current of the + input power source occurs. This prevents input voltage drop due to insufficient + current provided by the power source. Defaults to 4500000 uV (4.5V). + + richtek,avg-input-current-regulation: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + input current value in uA drained by the charger from the power source. + Defaults to 500000 uA (500mA). + +required: + - compatible + - reg + - interrupts + - richtek,output-charge-current + - richtek,end-of-charge-percentage + - richtek,battery-regulation-voltage + - richtek,boost-output-voltage + +additionalProperties: false + +examples: + - | + #include + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + charger@22 { + compatible = "richtek,rt9455"; + reg = <0x22>; + + interrupt-parent = <&gpio1>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + + richtek,output-charge-current = <500000>; + richtek,end-of-charge-percentage = <10>; + richtek,battery-regulation-voltage = <4200000>; + richtek,boost-output-voltage = <5050000>; + + richtek,min-input-voltage-regulation = <4500000>; + richtek,avg-input-current-regulation = <500000>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/rohm,bd99954.yaml b/Documentation/devicetree/bindings/power/supply/rohm,bd99954.yaml index 9852d2f..24b0695 100644 --- a/Documentation/devicetree/bindings/power/supply/rohm,bd99954.yaml +++ b/Documentation/devicetree/bindings/power/supply/rohm,bd99954.yaml @@ -110,7 +110,7 @@ properties: # multipleOf: 64000 # a charge cycle terminates when the battery voltage is above recharge # threshold, and the current is below this setting (7 in above chart) -# See also Documentation/devicetree/bindings/power/supply/battery.txt +# See also Documentation/devicetree/bindings/power/supply/battery.yaml reg: maxItems: 1 diff --git a/Documentation/devicetree/bindings/power/supply/rt9455_charger.txt b/Documentation/devicetree/bindings/power/supply/rt9455_charger.txt deleted file mode 100644 index 1e6107c..0000000 --- a/Documentation/devicetree/bindings/power/supply/rt9455_charger.txt +++ /dev/null @@ -1,46 +0,0 @@ -Binding for Richtek rt9455 battery charger - -Required properties: -- compatible: it should contain one of the following: - "richtek,rt9455". -- reg: integer, i2c address of the device. -- interrupts: interrupt mapping for GPIO IRQ, it should be - configured with IRQ_TYPE_LEVEL_LOW flag. -- richtek,output-charge-current: integer, output current from the charger to the - battery, in uA. -- richtek,end-of-charge-percentage: integer, percent of the output charge current. - When the current in constant-voltage phase drops - below output_charge_current x end-of-charge-percentage, - charge is terminated. -- richtek,battery-regulation-voltage: integer, maximum battery voltage in uV. -- richtek,boost-output-voltage: integer, maximum voltage provided to consumer - devices, when the charger is in boost mode, in uV. - -Optional properties: -- richtek,min-input-voltage-regulation: integer, input voltage level in uV, used to - decrease voltage level when the over current - of the input power source occurs. - This prevents input voltage drop due to insufficient - current provided by the power source. - Default: 4500000 uV (4.5V) -- richtek,avg-input-current-regulation: integer, input current value in uA drained by the - charger from the power source. - Default: 500000 uA (500mA) - -Example: - -rt9455@22 { - compatible = "richtek,rt9455"; - reg = <0x22>; - - interrupt-parent = <&gpio1>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - - richtek,output-charge-current = <500000>; - richtek,end-of-charge-percentage = <10>; - richtek,battery-regulation-voltage = <4200000>; - richtek,boost-output-voltage = <5050000>; - - richtek,min-input-voltage-regulation = <4500000>; - richtek,avg-input-current-regulation = <500000>; -}; diff --git a/Documentation/devicetree/bindings/power/supply/rx51-battery.txt b/Documentation/devicetree/bindings/power/supply/rx51-battery.txt deleted file mode 100644 index 9043845..0000000 --- a/Documentation/devicetree/bindings/power/supply/rx51-battery.txt +++ /dev/null @@ -1,25 +0,0 @@ -Binding for Nokia N900 battery - -The Nokia N900 battery status can be read via the TWL4030's A/D converter. - -Required properties: -- compatible: Should contain one of the following: - * "nokia,n900-battery" -- io-channels: Should contain IIO channel specifiers - for each element in io-channel-names. -- io-channel-names: Should contain the following values: - * "temp" - The ADC channel for temperature reading - * "bsi" - The ADC channel for battery size identification - * "vbat" - The ADC channel to measure the battery voltage - -Example from Nokia N900: - -battery: n900-battery { - compatible = "nokia,n900-battery"; - io-channels = <&twl4030_madc 0>, - <&twl4030_madc 4>, - <&twl4030_madc 12>; - io-channel-names = "temp", - "bsi", - "vbat"; -}; diff --git a/Documentation/devicetree/bindings/power/supply/sbs,sbs-battery.yaml b/Documentation/devicetree/bindings/power/supply/sbs,sbs-battery.yaml index a90b360..90b9d3d 100644 --- a/Documentation/devicetree/bindings/power/supply/sbs,sbs-battery.yaml +++ b/Documentation/devicetree/bindings/power/supply/sbs,sbs-battery.yaml @@ -12,12 +12,15 @@ maintainers: description: | Battery compatible with the smart battery system specifications -properties: +allOf: + - $ref: power-supply.yaml# +properties: compatible: oneOf: - items: - enum: + - ti,bq20z45 - ti,bq20z65 - ti,bq20z75 - enum: @@ -60,7 +63,7 @@ required: - compatible - reg -additionalProperties: false +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/power/supply/sbs,sbs-charger.yaml b/Documentation/devicetree/bindings/power/supply/sbs,sbs-charger.yaml new file mode 100644 index 0000000..cb73ffa --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sbs,sbs-charger.yaml @@ -0,0 +1,55 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/supply/sbs,sbs-charger.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SBS compliant charger + +maintainers: + - Sebastian Reichel + +description: | + Charger compatible with the smart battery system specifications + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - lltc,ltc4100 + - enum: + - sbs,sbs-charger + - items: + - const: sbs,sbs-charger + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + charger@9 { + compatible = "lltc,ltc4100", "sbs,sbs-charger"; + reg = <0x9>; + interrupt-parent = <&gpio6>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.txt b/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.txt deleted file mode 100644 index 4b21955..0000000 --- a/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.txt +++ /dev/null @@ -1,66 +0,0 @@ -Binding for sbs-manager - -Required properties: -- compatible: ",", "sbs,sbs-charger" as fallback. The part - number compatible string might be used in order to take care of vendor - specific registers. -- reg: integer, i2c address of the device. Should be <0xa>. -Optional properties: -- gpio-controller: Marks the port as GPIO controller. - See "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt. -- #gpio-cells: Should be <2>. The first cell is the pin number, the second cell - is used to specify optional parameters: - See "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt. - -From OS view the device is basically an i2c-mux used to communicate with up to -four smart battery devices at address 0xb. The driver actually implements this -behaviour. So standard i2c-mux nodes can be used to register up to four slave -batteries. Channels will be numerated starting from 1 to 4. - -Example: - -batman@a { - compatible = "lltc,ltc1760", "sbs,sbs-manager"; - reg = <0x0a>; - #address-cells = <1>; - #size-cells = <0>; - - gpio-controller; - #gpio-cells = <2>; - - i2c@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; - - battery@b { - compatible = "ti,bq2060", "sbs,sbs-battery"; - reg = <0x0b>; - sbs,battery-detect-gpios = <&batman 1 1>; - }; - }; - - i2c@2 { - #address-cells = <1>; - #size-cells = <0>; - reg = <2>; - - battery@b { - compatible = "ti,bq2060", "sbs,sbs-battery"; - reg = <0x0b>; - sbs,battery-detect-gpios = <&batman 2 1>; - }; - }; - - i2c@3 { - #address-cells = <1>; - #size-cells = <0>; - reg = <3>; - - battery@b { - compatible = "ti,bq2060", "sbs,sbs-battery"; - reg = <0x0b>; - sbs,battery-detect-gpios = <&batman 3 1>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.yaml b/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.yaml new file mode 100644 index 0000000..72e8f27 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/supply/sbs,sbs-manager.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SBS compliant manger + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - lltc,ltc1760 + - enum: + - sbs,sbs-manager + - items: + - const: sbs,sbs-manager + + reg: + const: 0xa + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + gpio-controller: true + + "#gpio-cells": + const: 2 + +required: + - compatible + - reg + +additionalProperties: false + +patternProperties: + "^i2c@[1-4]$": + type: object + + allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + +examples: + - | + #include + #include + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + batman: battery-manager@a { + compatible = "lltc,ltc1760", "sbs,sbs-manager"; + reg = <0x0a>; + #address-cells = <1>; + #size-cells = <0>; + + gpio-controller; + #gpio-cells = <2>; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + battery@b { + compatible = "ti,bq20z65", "sbs,sbs-battery"; + reg = <0x0b>; + sbs,battery-detect-gpios = <&batman 1 1>; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + battery@b { + compatible = "ti,bq20z65", "sbs,sbs-battery"; + reg = <0x0b>; + sbs,battery-detect-gpios = <&batman 2 1>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + battery@b { + compatible = "ti,bq20z65", "sbs,sbs-battery"; + reg = <0x0b>; + sbs,battery-detect-gpios = <&batman 3 1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt b/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt deleted file mode 100644 index 84e7415..0000000 --- a/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt +++ /dev/null @@ -1,21 +0,0 @@ -SBS sbs-charger -~~~~~~~~~~ - -Required properties: - - compatible: ",", "sbs,sbs-charger" as fallback. The part - number compatible string might be used in order to take care of vendor - specific registers. - -Optional properties: -- interrupts: Interrupt mapping for GPIO IRQ. Use in conjunction with - "interrupt-parent". If an interrupt is not provided the driver will switch - automatically to polling. - -Example: - - ltc4100@9 { - compatible = "lltc,ltc4100", "sbs,sbs-charger"; - reg = <0x9>; - interrupt-parent = <&gpio6>; - interrupts = <7 IRQ_TYPE_LEVEL_LOW>; - }; diff --git a/Documentation/devicetree/bindings/power/supply/sc2731-charger.yaml b/Documentation/devicetree/bindings/power/supply/sc2731-charger.yaml new file mode 100644 index 0000000..db1aa23 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sc2731-charger.yaml @@ -0,0 +1,53 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/sc2731-charger.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Spreadtrum SC2731 PMICs battery charger binding + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: sprd,sc2731-charger + + reg: + maxItems: 1 + + phys: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to the USB phy + + monitored-battery: + description: | + The charger uses the following battery properties + - charge-term-current-microamp: current for charge termination phase. + - constant-charge-voltage-max-microvolt: maximum constant input voltage. + See Documentation/devicetree/bindings/power/supply/battery.yaml + +additionalProperties: false + +examples: + - | + bat: battery { + compatible = "simple-battery"; + charge-term-current-microamp = <120000>; + constant-charge-voltage-max-microvolt = <4350000>; + }; + + pmic { + #address-cells = <1>; + #size-cells = <0>; + + battery@a00 { + compatible = "sprd,sc2731-charger"; + reg = <0x0>; + phys = <&ssphy>; + monitored-battery = <&bat>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/sc2731_charger.txt b/Documentation/devicetree/bindings/power/supply/sc2731_charger.txt deleted file mode 100644 index 5266fab..0000000 --- a/Documentation/devicetree/bindings/power/supply/sc2731_charger.txt +++ /dev/null @@ -1,40 +0,0 @@ -Spreadtrum SC2731 PMIC battery charger binding - -Required properties: - - compatible: Should be "sprd,sc2731-charger". - - reg: Address offset of charger register. - - phys: Contains a phandle to the USB phy. - -Optional Properties: -- monitored-battery: phandle of battery characteristics devicetree node. - The charger uses the following battery properties: -- charge-term-current-microamp: current for charge termination phase. -- constant-charge-voltage-max-microvolt: maximum constant input voltage. - See Documentation/devicetree/bindings/power/supply/battery.txt - -Example: - - bat: battery { - compatible = "simple-battery"; - charge-term-current-microamp = <120000>; - constant-charge-voltage-max-microvolt = <4350000>; - ...... - }; - - sc2731_pmic: pmic@0 { - compatible = "sprd,sc2731"; - reg = <0>; - spi-max-frequency = <26000000>; - interrupts = ; - interrupt-controller; - #interrupt-cells = <2>; - #address-cells = <1>; - #size-cells = <0>; - - charger@0 { - compatible = "sprd,sc2731-charger"; - reg = <0x0>; - phys = <&ssphy>; - monitored-battery = <&bat>; - }; - }; diff --git a/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt b/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt deleted file mode 100644 index b6359b5..0000000 --- a/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt +++ /dev/null @@ -1,59 +0,0 @@ -Spreadtrum SC27XX PMICs Fuel Gauge Unit Power Supply Bindings - -Required properties: -- compatible: Should be one of the following: - "sprd,sc2720-fgu", - "sprd,sc2721-fgu", - "sprd,sc2723-fgu", - "sprd,sc2730-fgu", - "sprd,sc2731-fgu". -- reg: The address offset of fuel gauge unit. -- battery-detect-gpios: GPIO for battery detection. -- io-channels: Specify the IIO ADC channels to get temperature and charge voltage. -- io-channel-names: Should be "bat-temp" or "charge-vol". -- nvmem-cells: A phandle to the calibration cells provided by eFuse device. -- nvmem-cell-names: Should be "fgu_calib". -- sprd,calib-resistance-micro-ohms: Specify the real resistance of coulomb counter - chip in micro Ohms. -- monitored-battery: Phandle of battery characteristics devicetree node. - See Documentation/devicetree/bindings/power/supply/battery.txt - -Example: - - bat: battery { - compatible = "simple-battery"; - charge-full-design-microamp-hours = <1900000>; - constant-charge-voltage-max-microvolt = <4350000>; - ocv-capacity-celsius = <20>; - ocv-capacity-table-0 = <4185000 100>, <4113000 95>, <4066000 90>, - <4022000 85>, <3983000 80>, <3949000 75>, - <3917000 70>, <3889000 65>, <3864000 60>, - <3835000 55>, <3805000 50>, <3787000 45>, - <3777000 40>, <3773000 35>, <3770000 30>, - <3765000 25>, <3752000 20>, <3724000 15>, - <3680000 10>, <3605000 5>, <3400000 0>; - ...... - }; - - sc2731_pmic: pmic@0 { - compatible = "sprd,sc2731"; - reg = <0>; - spi-max-frequency = <26000000>; - interrupts = ; - interrupt-controller; - #interrupt-cells = <2>; - #address-cells = <1>; - #size-cells = <0>; - - fgu@a00 { - compatible = "sprd,sc2731-fgu"; - reg = <0xa00>; - battery-detect-gpios = <&pmic_eic 9 GPIO_ACTIVE_HIGH>; - io-channels = <&pmic_adc 5>, <&pmic_adc 14>; - io-channel-names = "bat-temp", "charge-vol"; - nvmem-cells = <&fgu_calib>; - nvmem-cell-names = "fgu_calib"; - monitored-battery = <&bat>; - sprd,calib-resistance-micro-ohms = <21500>; - }; - }; diff --git a/Documentation/devicetree/bindings/power/supply/sc27xx-fg.yaml b/Documentation/devicetree/bindings/power/supply/sc27xx-fg.yaml new file mode 100644 index 0000000..e019cff --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sc27xx-fg.yaml @@ -0,0 +1,98 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/sc27xx-fg.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Spreadtrum SC27XX PMICs Fuel Gauge Unit Power Supply Bindings + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + enum: + - sprd,sc2720-fgu + - sprd,sc2721-fgu + - sprd,sc2723-fgu + - sprd,sc2730-fgu + - sprd,sc2731-fgu + + reg: + maxItems: 1 + + battery-detect-gpios: + maxItems: 1 + + io-channels: + items: + - description: Battery Temperature ADC + - description: Battery Charge Voltage ADC + + io-channel-names: + items: + - const: bat-temp + - const: charge-vol + + nvmem-cells: + maxItems: 1 + description: Calibration cells provided by eFuse device + + nvmem-cell-names: + const: fgu_calib + + sprd,calib-resistance-micro-ohms: + description: real resistance of coulomb counter chip in micro Ohms + + monitored-battery: true + +required: + - compatible + - reg + - battery-detect-gpios + - io-channels + - io-channel-names + - nvmem-cells + - nvmem-cell-names + - sprd,calib-resistance-micro-ohms + - monitored-battery + +additionalProperties: false + +examples: + - | + #include + bat: battery { + compatible = "simple-battery"; + charge-full-design-microamp-hours = <1900000>; + constant-charge-voltage-max-microvolt = <4350000>; + ocv-capacity-celsius = <20>; + ocv-capacity-table-0 = <4185000 100>, <4113000 95>, <4066000 90>, + <4022000 85>, <3983000 80>, <3949000 75>, + <3917000 70>, <3889000 65>, <3864000 60>, + <3835000 55>, <3805000 50>, <3787000 45>, + <3777000 40>, <3773000 35>, <3770000 30>, + <3765000 25>, <3752000 20>, <3724000 15>, + <3680000 10>, <3605000 5>, <3400000 0>; + // ... + }; + + pmic { + #address-cells = <1>; + #size-cells = <0>; + + battery@a00 { + compatible = "sprd,sc2731-fgu"; + reg = <0xa00>; + battery-detect-gpios = <&pmic_eic 9 GPIO_ACTIVE_HIGH>; + io-channels = <&pmic_adc 5>, <&pmic_adc 14>; + io-channel-names = "bat-temp", "charge-vol"; + nvmem-cells = <&fgu_calib>; + nvmem-cell-names = "fgu_calib"; + monitored-battery = <&bat>; + sprd,calib-resistance-micro-ohms = <21500>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/fg.txt b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-battery.txt similarity index 66% rename from Documentation/devicetree/bindings/power/supply/ab8500/fg.txt rename to Documentation/devicetree/bindings/power/supply/stericsson,ab8500-battery.txt index ccafcb9..ee125cb 100644 --- a/Documentation/devicetree/bindings/power/supply/ab8500/fg.txt +++ b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-battery.txt @@ -1,32 +1,9 @@ -=== AB8500 Fuel Gauge Driver === - -AB8500 is a mixed signal multimedia and power management -device comprising: power and energy-management-module, -wall-charger, usb-charger, audio codec, general purpose adc, -tvout, clock management and sim card interface. - -Fuelgauge support is part of energy-management-modules, other -components of this module are: -main-charger, usb-combo-charger and battery-temperature-monitoring. - -The properties below describes the node for fuelgauge driver. - -Required Properties: -- compatible = This shall be: "stericsson,ab8500-fg" -- battery = Shall be battery specific information - Example: - ab8500_fg { - compatible = "stericsson,ab8500-fg"; - battery = <&ab8500_battery>; - }; - -dependent node: - ab8500_battery: ab8500_battery { - }; - This node will provide information on 'thermistor interface' and - 'battery technology type' used. +AB85000 PMIC contains a node, which contains shared +information about the battery connected to the PMIC. +The node has no compatible property. Properties of this node are: + thermistor-on-batctrl: A boolean value indicating thermistor interface to battery @@ -55,4 +32,3 @@ battery-type: ab8500_battery: ab8500_battery { stericsson,battery-type = "LIPO"; } - diff --git a/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-btemp.yaml b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-btemp.yaml new file mode 100644 index 0000000..2f57aa5 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-btemp.yaml @@ -0,0 +1,73 @@ +# SPDX-License-Identifier: GPL-2.0 +# Copyright (C) 2021 Sebastian Reichel +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/stericsson,ab8500-btemp.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: AB8500 Battery Temperature Monitor + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: stericsson,ab8500-btemp + + battery: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to battery node + + interrupts: + maxItems: 5 + + interrupt-names: + items: + - const: BAT_CTRL_INDB + - const: BTEMP_LOW + - const: BTEMP_HIGH + - const: BTEMP_LOW_MEDIUM + - const: BTEMP_MEDIUM_HIGH + + io-channels: + maxItems: 2 + + io-channel-names: + items: + - const: btemp_ball + - const: bat_ctrl + +required: + - compatible + - battery + - interrupts + - interrupt-names + - io-channels + - io-channel-names + +additionalProperties: false + +examples: + - | + #include + pmic { + battery-temperature { + compatible = "stericsson,ab8500-btemp"; + battery = <&ab8500_battery>; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>, + <80 IRQ_TYPE_LEVEL_HIGH>, + <83 IRQ_TYPE_LEVEL_HIGH>, + <81 IRQ_TYPE_LEVEL_HIGH>, + <82 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "BAT_CTRL_INDB", + "BTEMP_LOW", + "BTEMP_HIGH", + "BTEMP_LOW_MEDIUM", + "BTEMP_MEDIUM_HIGH"; + io-channels = <&gpadc 0x02>, <&gpadc 0x01>; + io-channel-names = "btemp_ball", "bat_ctrl"; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-chargalg.yaml b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-chargalg.yaml new file mode 100644 index 0000000..0897231 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-chargalg.yaml @@ -0,0 +1,37 @@ +# SPDX-License-Identifier: GPL-2.0 +# Copyright (C) 2021 Sebastian Reichel +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/stericsson,ab8500-chargalg.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: AB8500 Charging Algorithm + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: stericsson,ab8500-chargalg + + battery: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to battery node + +required: + - compatible + - battery + +additionalProperties: false + +examples: + - | + pmic { + charging-algorithm { + compatible = "stericsson,ab8500-chargalg"; + battery = <&ab8500_battery>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-charger.yaml b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-charger.yaml new file mode 100644 index 0000000..e13305a --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-charger.yaml @@ -0,0 +1,123 @@ +# SPDX-License-Identifier: GPL-2.0 +# Copyright (C) 2021 Sebastian Reichel +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/stericsson,ab8500-charger.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: AB8500 Charger + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: stericsson,ab8500-charger + + battery: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to battery node + + vddadc-supply: + description: Supply for USB and Main charger + + autopower_cfg: + type: boolean + description: automatic poweron after powerloss + + interrupts: + maxItems: 14 + + interrupt-names: + items: + - const: MAIN_CH_UNPLUG_DET + - const: MAIN_CHARGE_PLUG_DET + - const: MAIN_EXT_CH_NOT_OK + - const: MAIN_CH_TH_PROT_R + - const: MAIN_CH_TH_PROT_F + - const: VBUS_DET_F + - const: VBUS_DET_R + - const: USB_LINK_STATUS + - const: USB_CH_TH_PROT_R + - const: USB_CH_TH_PROT_F + - const: USB_CHARGER_NOT_OKR + - const: VBUS_OVV + - const: CH_WD_EXP + - const: VBUS_CH_DROP_END + + io-channels: + minItems: 2 + maxItems: 4 + + io-channel-names: + oneOf: + - items: + - const: main_charger_v + - const: main_charger_c + - const: vbus_v + - const: usb_charger_c + - items: + - const: vbus_v + - const: usb_charger_c + + +required: + - compatible + - battery + - vddadc-supply + - interrupts + - interrupt-names + - io-channels + - io-channel-names + +additionalProperties: false + +examples: + - | + #include + pmic { + charger { + compatible = "stericsson,ab8500-charger"; + battery = <&ab8500_battery>; + vddadc-supply = <&ab8500_ldo_tvout_reg>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>, + <11 IRQ_TYPE_LEVEL_HIGH>, + <0 IRQ_TYPE_LEVEL_HIGH>, + <107 IRQ_TYPE_LEVEL_HIGH>, + <106 IRQ_TYPE_LEVEL_HIGH>, + <14 IRQ_TYPE_LEVEL_HIGH>, + <15 IRQ_TYPE_LEVEL_HIGH>, + <79 IRQ_TYPE_LEVEL_HIGH>, + <105 IRQ_TYPE_LEVEL_HIGH>, + <104 IRQ_TYPE_LEVEL_HIGH>, + <89 IRQ_TYPE_LEVEL_HIGH>, + <22 IRQ_TYPE_LEVEL_HIGH>, + <21 IRQ_TYPE_LEVEL_HIGH>, + <16 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "MAIN_CH_UNPLUG_DET", + "MAIN_CHARGE_PLUG_DET", + "MAIN_EXT_CH_NOT_OK", + "MAIN_CH_TH_PROT_R", + "MAIN_CH_TH_PROT_F", + "VBUS_DET_F", + "VBUS_DET_R", + "USB_LINK_STATUS", + "USB_CH_TH_PROT_R", + "USB_CH_TH_PROT_F", + "USB_CHARGER_NOT_OKR", + "VBUS_OVV", + "CH_WD_EXP", + "VBUS_CH_DROP_END"; + io-channels = <&gpadc 0x03>, + <&gpadc 0x0a>, + <&gpadc 0x09>, + <&gpadc 0x0b>; + io-channel-names = "main_charger_v", + "main_charger_c", + "vbus_v", + "usb_charger_c"; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-fg.yaml b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-fg.yaml new file mode 100644 index 0000000..db342e5 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/stericsson,ab8500-fg.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: GPL-2.0 +# Copyright (C) 2021 Sebastian Reichel +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/stericsson,ab8500-fg.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: AB8500 Fuel Gauge + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: stericsson,ab8500-fg + + battery: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to battery node + + interrupts: + maxItems: 5 + + interrupt-names: + items: + - const: NCONV_ACCU + - const: BATT_OVV + - const: LOW_BAT_F + - const: CC_INT_CALIB + - const: CCEOC + + io-channels: + maxItems: 1 + + io-channel-names: + items: + - const: main_bat_v + +required: + - compatible + - battery + - interrupts + - interrupt-names + - io-channels + - io-channel-names + +additionalProperties: false + +examples: + - | + #include + pmic { + fuel-gauge { + compatible = "stericsson,ab8500-fg"; + battery = <&ab8500_battery>; + interrupts = <24 IRQ_TYPE_LEVEL_HIGH>, + <8 IRQ_TYPE_LEVEL_HIGH>, + <28 IRQ_TYPE_LEVEL_HIGH>, + <27 IRQ_TYPE_LEVEL_HIGH>, + <26 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "NCONV_ACCU", + "BATT_OVV", + "LOW_BAT_F", + "CC_INT_CALIB", + "CCEOC"; + io-channels = <&gpadc 0x08>; + io-channel-names = "main_bat_v"; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt b/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt deleted file mode 100644 index de45e1a..0000000 --- a/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt +++ /dev/null @@ -1,39 +0,0 @@ -TI BQ24735 Charge Controller -~~~~~~~~~~ - -Required properties : - - compatible : "ti,bq24735" - -Optional properties : - - interrupts : Specify the interrupt to be used to trigger when the AC - adapter is either plugged in or removed. - - ti,ac-detect-gpios : This GPIO is optionally used to read the AC adapter - status. This is a Host GPIO that is configured as an input and connected - to the ACOK pin on the bq24735. Note: for backwards compatibility reasons, - the GPIO must be active on AC adapter absence despite ACOK being active - (high) on AC adapter presence. - - ti,charge-current : Used to control and set the charging current. This value - must be between 128mA and 8.128A with a 64mA step resolution. The POR value - is 0x0000h. This number is in mA (e.g. 8192), see spec for more information - about the ChargeCurrent (0x14h) register. - - ti,charge-voltage : Used to control and set the charging voltage. This value - must be between 1.024V and 19.2V with a 16mV step resolution. The POR value - is 0x0000h. This number is in mV (e.g. 19200), see spec for more information - about the ChargeVoltage (0x15h) register. - - ti,input-current : Used to control and set the charger input current. This - value must be between 128mA and 8.064A with a 128mA step resolution. The - POR value is 0x1000h. This number is in mA (e.g. 8064), see the spec for - more information about the InputCurrent (0x3fh) register. - - ti,external-control : Indicates that the charger is configured externally - and that the host should not attempt to enable/disable charging or set the - charge voltage/current. - - poll-interval : In case 'interrupts' is not specified, poll AC adapter - presence with this interval (milliseconds). - -Example: - - bq24735@9 { - compatible = "ti,bq24735"; - reg = <0x9>; - ti,ac-detect-gpios = <&gpio 72 0x1>; - } diff --git a/Documentation/devicetree/bindings/power/supply/ti,lp8727.yaml b/Documentation/devicetree/bindings/power/supply/ti,lp8727.yaml new file mode 100644 index 0000000..a23f665 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ti,lp8727.yaml @@ -0,0 +1,90 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/supply/ti,lp8727.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Binding for TI/National Semiconductor LP8727 Charger + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: ti,lp8727 + + reg: + const: 0x27 + + interrupts: + maxItems: 1 + + debounce-ms: + description: interrupt debounce time in ms + +patternProperties: + '^(ac|usb)$': + type: object + description: USB/AC charging parameters + properties: + charger-type: + enum: + - ac + - usb + + eoc-level: + $ref: /schemas/types.yaml#/definitions/uint8 + minimum: 0 + maximum: 6 + description: | + End of Charge Percentage with the following mapping: + 0 = 5%, 1 = 10%, 2 = 16%, 3 = 20%, 4 = 25%, 5 = 33%, 6 = 50% + + charging-current: + $ref: /schemas/types.yaml#/definitions/uint8 + minimum: 0 + maximum: 9 + description: | + Charging current with the following mapping: + 0 = 90mA, 1 = 100mA, 2 = 400mA, 3 = 450mA, 4 = 500mA, 5 = 600mA, + 6 = 700mA, 7 = 800mA, 8 = 900mA, 9 = 1000mA + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + lp8727: charger@27 { + compatible = "ti,lp8727"; + reg = <0x27>; + interrupt-parent = <&gpio5>; + interrupts = <6 IRQ_TYPE_EDGE_FALLING>; + debounce-ms = <300>; + + /* AC charger: 5% EOC and 500mA charging current */ + ac { + charger-type = "ac"; + eoc-level = /bits/ 8 <0>; + charging-current = /bits/ 8 <4>; + }; + + /* USB charger: 10% EOC and 400mA charging current */ + usb { + charger-type = "usb"; + eoc-level = /bits/ 8 <1>; + charging-current = /bits/ 8 <2>; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/power/supply/tps65090-charger.yaml b/Documentation/devicetree/bindings/power/supply/tps65090-charger.yaml new file mode 100644 index 0000000..f2dd38b --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/tps65090-charger.yaml @@ -0,0 +1,36 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/tps65090-charger.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: TPS65090 Frontend PMU with Switchmode Charger + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: ti,tps65090-charger + + ti,enable-low-current-chrg: + type: boolean + description: | + Enables charging when a low current is detected while the default logic is to stop charging. + +required: + - compatible + +additionalProperties: false + +examples: + - | + pmic { + charger { + compatible = "ti,tps65090-charger"; + ti,enable-low-current-chrg; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/tps65090.txt b/Documentation/devicetree/bindings/power/supply/tps65090.txt deleted file mode 100644 index 8e5e0d3..0000000 --- a/Documentation/devicetree/bindings/power/supply/tps65090.txt +++ /dev/null @@ -1,17 +0,0 @@ -TPS65090 Frontend PMU with Switchmode Charger - -Required Properties: --compatible: "ti,tps65090-charger" - -Optional Properties: --ti,enable-low-current-chrg: Enables charging when a low current is detected - while the default logic is to stop charging. - -This node is a subnode of the tps65090 PMIC. - -Example: - - tps65090-charger { - compatible = "ti,tps65090-charger"; - ti,enable-low-current-chrg; - }; diff --git a/Documentation/devicetree/bindings/power/supply/tps65217-charger.yaml b/Documentation/devicetree/bindings/power/supply/tps65217-charger.yaml new file mode 100644 index 0000000..a33408c --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/tps65217-charger.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/tps65217-charger.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: TPS65217 Charger + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: ti,tps65217-charger + + interrupts: + minItems: 2 + maxItems: 2 + + interrupt-names: + items: + - const: USB + - const: AC + +required: + - compatible + - interrupts + - interrupt-names + +additionalProperties: false + +examples: + - | + pmic { + charger { + compatible = "ti,tps65217-charger"; + interrupts = <0>, <1>; + interrupt-names = "USB", "AC"; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt deleted file mode 100644 index a11072c..0000000 --- a/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt +++ /dev/null @@ -1,17 +0,0 @@ -TPS65217 Charger - -Required Properties: --compatible: "ti,tps65217-charger" --interrupts: TPS65217 interrupt numbers for the AC and USB charger input change. - Should be <0> for the USB charger and <1> for the AC adapter. --interrupt-names: Should be "USB" and "AC" - -This node is a subnode of the tps65217 PMIC. - -Example: - - tps65217-charger { - compatible = "ti,tps65217-charger"; - interrupts = <0>, <1>; - interrupt-names = "USB", "AC"; - }; diff --git a/Documentation/devicetree/bindings/power/supply/twl-charger.txt b/Documentation/devicetree/bindings/power/supply/twl-charger.txt deleted file mode 100644 index 3b4ea1b..0000000 --- a/Documentation/devicetree/bindings/power/supply/twl-charger.txt +++ /dev/null @@ -1,30 +0,0 @@ -TWL BCI (Battery Charger Interface) - -The battery charger needs to interact with the USB phy in order -to know when charging is permissible, and when there is a connection -or disconnection. - -The choice of phy cannot be configured at a hardware level, so there -is no value in explicit configuration in device-tree. Rather -if there is a sibling of the BCI node which is compatible with -"ti,twl4030-usb", then that is used to determine when and how -use USB power for charging. - -Required properties: -- compatible: - - "ti,twl4030-bci" -- interrupts: two interrupt lines from the TWL SIH (secondary - interrupt handler) - interrupts 9 and 2. - -Optional properties: -- ti,bb-uvolt: microvolts for charging the backup battery. -- ti,bb-uamp: microamps for charging the backup battery. - -Examples: - -bci { - compatible = "ti,twl4030-bci"; - interrupts = <9>, <2>; - ti,bb-uvolt = <3200000>; - ti,bb-uamp = <150>; -}; diff --git a/Documentation/devicetree/bindings/power/supply/twl4030-charger.yaml b/Documentation/devicetree/bindings/power/supply/twl4030-charger.yaml new file mode 100644 index 0000000..fe3f32a --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/twl4030-charger.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/twl4030-charger.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: TWL4030 BCI (Battery Charger Interface) + +description: | + The battery charger needs to interact with the USB phy in order to know when + charging is permissible, and when there is a connection or disconnection. + + The choice of phy cannot be configured at a hardware level, so there is no + value in explicit configuration in device-tree. Rather if there is a sibling + of the BCI node which is compatible with "ti,twl4030-usb", then that is used + to determine when and how use USB power for charging. + +maintainers: + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + const: ti,twl4030-bci + + interrupts: + minItems: 2 + maxItems: 2 + + ti,bb-uvolt: + $ref: /schemas/types.yaml#/definitions/uint32 + description: microvolts for charging the backup battery + + ti,bb-uamp: + $ref: /schemas/types.yaml#/definitions/uint32 + description: microamps for charging the backup battery + + io-channels: + items: + - description: Accessory Charger Voltage Channel + + io-channel-names: + items: + - const: vac + + bci3v1-supply: + description: 3.1V USB regulator + +required: + - compatible + - interrupts + +additionalProperties: false + +examples: + - | + pmic { + charger { + compatible = "ti,twl4030-bci"; + interrupts = <9>, <2>; + ti,bb-uvolt = <3200000>; + ti,bb-uamp = <150>; + io-channels = <&twl_madc 11>; + io-channel-names = "vac"; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-ac-power-supply.yaml b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-ac-power-supply.yaml new file mode 100644 index 0000000..dcda666 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-ac-power-supply.yaml @@ -0,0 +1,32 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/x-powers,axp20x-ac-power-supply.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: AXP20x AC power-supply + +description: | + The AXP20X can read the current current and voltage supplied by AC by + reading ADC channels from the AXP20X ADC. The AXP22X is only able to + tell if an AC power supply is present and usable. AXP813/AXP803 are + able to limit current and supply voltage + +maintainers: + - Chen-Yu Tsai + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + enum: + - x-powers,axp202-ac-power-supply + - x-powers,axp221-ac-power-supply + - x-powers,axp813-ac-power-supply + +required: + - compatible + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml new file mode 100644 index 0000000..86e8a71 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml @@ -0,0 +1,30 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/x-powers,axp20x-battery-power-supply.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: AXP20x Battery power-supply + +description: | + The supported devices can read the battery voltage, charge and discharge + currents of the battery by reading ADC channels from the ADC. + +maintainers: + - Chen-Yu Tsai + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + enum: + - x-powers,axp209-battery-power-supply + - x-powers,axp221-battery-power-supply + - x-powers,axp813-battery-power-supply + +required: + - compatible + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml new file mode 100644 index 0000000..61f1b32 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml @@ -0,0 +1,33 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/power/supply/x-powers,axp20x-usb-power-supply.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: AXP20x USB power-supply + +description: | + The AXP223 PMIC shares most of its behaviour with the AXP221 but has slight + variations such as the former being able to set the VBUS power supply max + current to 100mA, unlike the latter. + +maintainers: + - Chen-Yu Tsai + - Sebastian Reichel + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + enum: + - x-powers,axp202-usb-power-supply + - x-powers,axp221-usb-power-supply + - x-powers,axp223-usb-power-supply + - x-powers,axp813-usb-power-supply + + +required: + - compatible + +additionalProperties: false diff --git a/Documentation/power/power_supply_class.rst b/Documentation/power/power_supply_class.rst index 7b8c42f..c04fabe 100644 --- a/Documentation/power/power_supply_class.rst +++ b/Documentation/power/power_supply_class.rst @@ -233,7 +233,7 @@ Devicetree battery characteristics ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Drivers should call power_supply_get_battery_info() to obtain battery characteristics from a devicetree battery node, defined in -Documentation/devicetree/bindings/power/supply/battery.txt. This is +Documentation/devicetree/bindings/power/supply/battery.yaml. This is implemented in drivers/power/supply/bq27xxx_battery.c. Properties in struct power_supply_battery_info and their counterparts in the diff --git a/MAINTAINERS b/MAINTAINERS index 30b63ea..a938f79 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -10175,7 +10175,7 @@ F: drivers/misc/eeprom/eeprom.c LEGO MINDSTORMS EV3 R: David Lechner S: Maintained -F: Documentation/devicetree/bindings/power/supply/lego_ev3_battery.txt +F: Documentation/devicetree/bindings/power/supply/lego,ev3-battery.yaml F: arch/arm/boot/dts/da850-lego-ev3.dts F: drivers/power/supply/lego_ev3_battery.c @@ -12002,6 +12002,14 @@ F: drivers/scsi/smartpqi/smartpqi*.[ch] F: include/linux/cciss*.h F: include/uapi/linux/cciss*.h +MICROSOFT SURFACE BATTERY AND AC DRIVERS +M: Maximilian Luz +L: linux-pm@vger.kernel.org +L: platform-driver-x86@vger.kernel.org +S: Maintained +F: drivers/power/supply/surface_battery.c +F: drivers/power/supply/surface_charger.c + MICROSOFT SURFACE DTX DRIVER M: Maximilian Luz L: platform-driver-x86@vger.kernel.org @@ -15854,6 +15862,13 @@ S: Supported W: http://www.ibm.com/developerworks/linux/linux390/ F: drivers/s390/scsi/zfcp_* +S3C ADC BATTERY DRIVER +M: Krzysztof Kozlowski +L: linux-samsung-soc@vger.kernel.org +S: Odd Fixes +F: drivers/power/supply/s3c_adc_battery.c +F: include/linux/s3c_adc_battery.h + S3C24XX SD/MMC Driver M: Ben Dooks L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) diff --git a/drivers/mfd/ab8500-core.c b/drivers/mfd/ab8500-core.c index a903791..22c0e3d 100644 --- a/drivers/mfd/ab8500-core.c +++ b/drivers/mfd/ab8500-core.c @@ -19,7 +19,6 @@ #include #include #include -#include #include #include #include @@ -609,14 +608,14 @@ int ab8500_suspend(struct ab8500 *ab8500) } static const struct mfd_cell ab8500_bm_devs[] = { - MFD_CELL_OF("ab8500-charger", NULL, &ab8500_bm_data, - sizeof(ab8500_bm_data), 0, "stericsson,ab8500-charger"), - MFD_CELL_OF("ab8500-btemp", NULL, &ab8500_bm_data, - sizeof(ab8500_bm_data), 0, "stericsson,ab8500-btemp"), - MFD_CELL_OF("ab8500-fg", NULL, &ab8500_bm_data, - sizeof(ab8500_bm_data), 0, "stericsson,ab8500-fg"), - MFD_CELL_OF("ab8500-chargalg", NULL, &ab8500_bm_data, - sizeof(ab8500_bm_data), 0, "stericsson,ab8500-chargalg"), + MFD_CELL_OF("ab8500-charger", NULL, NULL, 0, 0, + "stericsson,ab8500-charger"), + MFD_CELL_OF("ab8500-btemp", NULL, NULL, 0, 0, + "stericsson,ab8500-btemp"), + MFD_CELL_OF("ab8500-fg", NULL, NULL, 0, 0, + "stericsson,ab8500-fg"), + MFD_CELL_OF("ab8500-chargalg", NULL, NULL, 0, 0, + "stericsson,ab8500-chargalg"), }; static const struct mfd_cell ab8500_devs[] = { diff --git a/drivers/power/reset/Makefile b/drivers/power/reset/Makefile index 4f959b6..cf3f4d0 100644 --- a/drivers/power/reset/Makefile +++ b/drivers/power/reset/Makefile @@ -11,7 +11,7 @@ obj-$(CONFIG_POWER_RESET_GEMINI_POWEROFF) += gemini-poweroff.o obj-$(CONFIG_POWER_RESET_GPIO) += gpio-poweroff.o obj-$(CONFIG_POWER_RESET_GPIO_RESTART) += gpio-restart.o obj-$(CONFIG_POWER_RESET_HISI) += hisi-reboot.o -obj-${CONFIG_POWER_RESET_LINKSTATION} += linkstation-poweroff.o +obj-$(CONFIG_POWER_RESET_LINKSTATION) += linkstation-poweroff.o obj-$(CONFIG_POWER_RESET_MSM) += msm-poweroff.o obj-$(CONFIG_POWER_RESET_MT6323) += mt6323-poweroff.o obj-$(CONFIG_POWER_RESET_OXNAS) += oxnas-restart.o diff --git a/drivers/power/reset/at91-reset.c b/drivers/power/reset/at91-reset.c index 3ff9d93..0266494 100644 --- a/drivers/power/reset/at91-reset.c +++ b/drivers/power/reset/at91-reset.c @@ -192,7 +192,7 @@ static int __init at91_reset_probe(struct platform_device *pdev) if (!reset) return -ENOMEM; - reset->rstc_base = of_iomap(pdev->dev.of_node, 0); + reset->rstc_base = devm_of_iomap(&pdev->dev, pdev->dev.of_node, 0, NULL); if (!reset->rstc_base) { dev_err(&pdev->dev, "Could not map reset controller address\n"); return -ENODEV; @@ -202,7 +202,7 @@ static int __init at91_reset_probe(struct platform_device *pdev) /* we need to shutdown the ddr controller, so get ramc base */ for_each_matching_node_and_match(np, at91_ramc_of_match, &match) { reset->ramc_lpr = (u32)match->data; - reset->ramc_base[idx] = of_iomap(np, 0); + reset->ramc_base[idx] = devm_of_iomap(&pdev->dev, np, 0, NULL); if (!reset->ramc_base[idx]) { dev_err(&pdev->dev, "Could not map ram controller address\n"); of_node_put(np); diff --git a/drivers/power/reset/hisi-reboot.c b/drivers/power/reset/hisi-reboot.c index 0ba5fdc..3440934 100644 --- a/drivers/power/reset/hisi-reboot.c +++ b/drivers/power/reset/hisi-reboot.c @@ -1,8 +1,8 @@ // SPDX-License-Identifier: GPL-2.0-only /* - * Hisilicon SoC reset code + * HiSilicon SoC reset code * - * Copyright (c) 2014 Hisilicon Ltd. + * Copyright (c) 2014 HiSilicon Ltd. * Copyright (c) 2014 Linaro Ltd. * * Author: Haojian Zhuang @@ -68,6 +68,7 @@ static const struct of_device_id hisi_reboot_of_match[] = { { .compatible = "hisilicon,sysctrl" }, {} }; +MODULE_DEVICE_TABLE(of, hisi_reboot_of_match); static struct platform_driver hisi_reboot_driver = { .probe = hisi_reboot_probe, diff --git a/drivers/power/reset/ltc2952-poweroff.c b/drivers/power/reset/ltc2952-poweroff.c index 3189279..d1495af 100644 --- a/drivers/power/reset/ltc2952-poweroff.c +++ b/drivers/power/reset/ltc2952-poweroff.c @@ -55,6 +55,7 @@ #include #include #include +#include struct ltc2952_poweroff { struct hrtimer timer_trigger; @@ -172,10 +173,17 @@ static void ltc2952_poweroff_default(struct ltc2952_poweroff *data) static int ltc2952_poweroff_init(struct platform_device *pdev) { int ret; + u32 trigger_delay_ms; struct ltc2952_poweroff *data = platform_get_drvdata(pdev); ltc2952_poweroff_default(data); + if (!device_property_read_u32(&pdev->dev, "trigger-delay-ms", + &trigger_delay_ms)) { + data->trigger_delay = ktime_set(trigger_delay_ms / MSEC_PER_SEC, + (trigger_delay_ms % MSEC_PER_SEC) * NSEC_PER_MSEC); + } + data->gpio_watchdog = devm_gpiod_get(&pdev->dev, "watchdog", GPIOD_OUT_LOW); if (IS_ERR(data->gpio_watchdog)) { diff --git a/drivers/power/reset/restart-poweroff.c b/drivers/power/reset/restart-poweroff.c index d233daa..04d4228 100644 --- a/drivers/power/reset/restart-poweroff.c +++ b/drivers/power/reset/restart-poweroff.c @@ -45,6 +45,7 @@ static const struct of_device_id of_restart_poweroff_match[] = { { .compatible = "restart-poweroff", }, {}, }; +MODULE_DEVICE_TABLE(of, of_restart_poweroff_match); static struct platform_driver restart_poweroff_driver = { .probe = restart_poweroff_probe, diff --git a/drivers/power/reset/vexpress-poweroff.c b/drivers/power/reset/vexpress-poweroff.c index 1fdbcbd..447ffda 100644 --- a/drivers/power/reset/vexpress-poweroff.c +++ b/drivers/power/reset/vexpress-poweroff.c @@ -133,7 +133,7 @@ static int vexpress_reset_probe(struct platform_device *pdev) case FUNC_REBOOT: ret = _vexpress_register_restart_handler(&pdev->dev); break; - }; + } return ret; } diff --git a/drivers/power/supply/88pm860x_battery.c b/drivers/power/supply/88pm860x_battery.c index 590da88..f3f3f8c 100644 --- a/drivers/power/supply/88pm860x_battery.c +++ b/drivers/power/supply/88pm860x_battery.c @@ -109,8 +109,8 @@ struct pm860x_battery_info { }; struct ccnt { - unsigned long long int pos; - unsigned long long int neg; + unsigned long long pos; + unsigned long long neg; unsigned int spos; unsigned int sneg; diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig index 006b95e..e696364 100644 --- a/drivers/power/supply/Kconfig +++ b/drivers/power/supply/Kconfig @@ -698,17 +698,17 @@ config BATTERY_GAUGE_LTC2941 config AB8500_BM bool "AB8500 Battery Management Driver" - depends on AB8500_CORE && AB8500_GPADC && (IIO = y) + depends on AB8500_CORE && AB8500_GPADC && (IIO = y) && OF help Say Y to include support for AB8500 battery management. config BATTERY_GOLDFISH tristate "Goldfish battery driver" - depends on GOLDFISH || COMPILE_TEST depends on HAS_IOMEM help - Say Y to enable support for the battery and AC power in the - Goldfish emulator. + Say Y to enable support for the Goldfish battery and AC power + driver. Originated in the Android Studio Emulator (goldfish) it is + going to be used in other emulators. config BATTERY_RT5033 tristate "RT5033 fuel gauge support" @@ -801,4 +801,36 @@ config BATTERY_ACER_A500 help Say Y to include support for Acer Iconia Tab A500 battery fuel gauge. +config BATTERY_SURFACE + tristate "Battery driver for 7th-generation Microsoft Surface devices" + depends on SURFACE_AGGREGATOR_REGISTRY + help + Driver for battery devices connected via/managed by the Surface System + Aggregator Module (SSAM). + + This driver provides battery-information and -status support for + Surface devices where said data is not exposed via the standard ACPI + devices. On those models (7th-generation), battery-information is + instead handled directly via SSAM client devices and this driver. + + Say M or Y here to include battery status support for 7th-generation + Microsoft Surface devices, i.e. Surface Pro 7, Surface Laptop 3, + Surface Book 3, and Surface Laptop Go. + +config CHARGER_SURFACE + tristate "AC driver for 7th-generation Microsoft Surface devices" + depends on SURFACE_AGGREGATOR_REGISTRY + help + Driver for AC devices connected via/managed by the Surface System + Aggregator Module (SSAM). + + This driver provides AC-information and -status support for Surface + devices where said data is not exposed via the standard ACPI devices. + On those models (7th-generation), AC-information is instead handled + directly via a SSAM client device and this driver. + + Say M or Y here to include AC status support for 7th-generation + Microsoft Surface devices, i.e. Surface Pro 7, Surface Laptop 3, + Surface Book 3, and Surface Laptop Go. + endif # POWER_SUPPLY diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile index 5e5fdbb..a7309a3 100644 --- a/drivers/power/supply/Makefile +++ b/drivers/power/supply/Makefile @@ -101,3 +101,5 @@ obj-$(CONFIG_CHARGER_BD99954) += bd99954-charger.o obj-$(CONFIG_CHARGER_WILCO) += wilco-charger.o obj-$(CONFIG_RN5T618_POWER) += rn5t618_power.o obj-$(CONFIG_BATTERY_ACER_A500) += acer_a500_battery.o +obj-$(CONFIG_BATTERY_SURFACE) += surface_battery.o +obj-$(CONFIG_CHARGER_SURFACE) += surface_charger.o diff --git a/include/linux/mfd/abx500/ab8500-bm.h b/drivers/power/supply/ab8500-bm.h similarity index 68% rename from include/linux/mfd/abx500/ab8500-bm.h rename to drivers/power/supply/ab8500-bm.h index 903e94c..41c69a4 100644 --- a/include/linux/mfd/abx500/ab8500-bm.h +++ b/drivers/power/supply/ab8500-bm.h @@ -1,15 +1,9 @@ /* SPDX-License-Identifier: GPL-2.0-only */ -/* - * Copyright ST-Ericsson 2012. - * - * Author: Arun Murthy - */ -#ifndef _AB8500_BM_H -#define _AB8500_BM_H +#ifndef _AB8500_CHARGER_H_ +#define _AB8500_CHARGER_H_ #include -#include /* * System control 2 register offsets. @@ -273,6 +267,277 @@ enum bup_vch_sel { #define BUS_PP_PRECHG_CURRENT_MASK 0x0E #define BUS_POWER_PATH_PRECHG_ENA 0x01 +/* + * ADC for the battery thermistor. + * When using the ABx500_ADC_THERM_BATCTRL the battery ID resistor is combined + * with a NTC resistor to both identify the battery and to measure its + * temperature. Different phone manufactures uses different techniques to both + * identify the battery and to read its temperature. + */ +enum abx500_adc_therm { + ABx500_ADC_THERM_BATCTRL, + ABx500_ADC_THERM_BATTEMP, +}; + +/** + * struct abx500_res_to_temp - defines one point in a temp to res curve. To + * be used in battery packs that combines the identification resistor with a + * NTC resistor. + * @temp: battery pack temperature in Celsius + * @resist: NTC resistor net total resistance + */ +struct abx500_res_to_temp { + int temp; + int resist; +}; + +/** + * struct abx500_v_to_cap - Table for translating voltage to capacity + * @voltage: Voltage in mV + * @capacity: Capacity in percent + */ +struct abx500_v_to_cap { + int voltage; + int capacity; +}; + +/* Forward declaration */ +struct abx500_fg; + +/** + * struct abx500_fg_parameters - Fuel gauge algorithm parameters, in seconds + * if not specified + * @recovery_sleep_timer: Time between measurements while recovering + * @recovery_total_time: Total recovery time + * @init_timer: Measurement interval during startup + * @init_discard_time: Time we discard voltage measurement at startup + * @init_total_time: Total init time during startup + * @high_curr_time: Time current has to be high to go to recovery + * @accu_charging: FG accumulation time while charging + * @accu_high_curr: FG accumulation time in high current mode + * @high_curr_threshold: High current threshold, in mA + * @lowbat_threshold: Low battery threshold, in mV + * @overbat_threshold: Over battery threshold, in mV + * @battok_falling_th_sel0 Threshold in mV for battOk signal sel0 + * Resolution in 50 mV step. + * @battok_raising_th_sel1 Threshold in mV for battOk signal sel1 + * Resolution in 50 mV step. + * @user_cap_limit Capacity reported from user must be within this + * limit to be considered as sane, in percentage + * points. + * @maint_thres This is the threshold where we stop reporting + * battery full while in maintenance, in per cent + * @pcut_enable: Enable power cut feature in ab8505 + * @pcut_max_time: Max time threshold + * @pcut_flag_time: Flagtime threshold + * @pcut_max_restart: Max number of restarts + * @pcut_debounce_time: Sets battery debounce time + */ +struct abx500_fg_parameters { + int recovery_sleep_timer; + int recovery_total_time; + int init_timer; + int init_discard_time; + int init_total_time; + int high_curr_time; + int accu_charging; + int accu_high_curr; + int high_curr_threshold; + int lowbat_threshold; + int overbat_threshold; + int battok_falling_th_sel0; + int battok_raising_th_sel1; + int user_cap_limit; + int maint_thres; + bool pcut_enable; + u8 pcut_max_time; + u8 pcut_flag_time; + u8 pcut_max_restart; + u8 pcut_debounce_time; +}; + +/** + * struct abx500_charger_maximization - struct used by the board config. + * @use_maxi: Enable maximization for this battery type + * @maxi_chg_curr: Maximum charger current allowed + * @maxi_wait_cycles: cycles to wait before setting charger current + * @charger_curr_step delta between two charger current settings (mA) + */ +struct abx500_maxim_parameters { + bool ena_maxi; + int chg_curr; + int wait_cycles; + int charger_curr_step; +}; + +/** + * struct abx500_battery_type - different batteries supported + * @name: battery technology + * @resis_high: battery upper resistance limit + * @resis_low: battery lower resistance limit + * @charge_full_design: Maximum battery capacity in mAh + * @nominal_voltage: Nominal voltage of the battery in mV + * @termination_vol: max voltage upto which battery can be charged + * @termination_curr battery charging termination current in mA + * @recharge_cap battery capacity limit that will trigger a new + * full charging cycle in the case where maintenan- + * -ce charging has been disabled + * @normal_cur_lvl: charger current in normal state in mA + * @normal_vol_lvl: charger voltage in normal state in mV + * @maint_a_cur_lvl: charger current in maintenance A state in mA + * @maint_a_vol_lvl: charger voltage in maintenance A state in mV + * @maint_a_chg_timer_h: charge time in maintenance A state + * @maint_b_cur_lvl: charger current in maintenance B state in mA + * @maint_b_vol_lvl: charger voltage in maintenance B state in mV + * @maint_b_chg_timer_h: charge time in maintenance B state + * @low_high_cur_lvl: charger current in temp low/high state in mA + * @low_high_vol_lvl: charger voltage in temp low/high state in mV' + * @battery_resistance: battery inner resistance in mOhm. + * @n_r_t_tbl_elements: number of elements in r_to_t_tbl + * @r_to_t_tbl: table containing resistance to temp points + * @n_v_cap_tbl_elements: number of elements in v_to_cap_tbl + * @v_to_cap_tbl: Voltage to capacity (in %) table + * @n_batres_tbl_elements number of elements in the batres_tbl + * @batres_tbl battery internal resistance vs temperature table + */ +struct abx500_battery_type { + int name; + int resis_high; + int resis_low; + int charge_full_design; + int nominal_voltage; + int termination_vol; + int termination_curr; + int recharge_cap; + int normal_cur_lvl; + int normal_vol_lvl; + int maint_a_cur_lvl; + int maint_a_vol_lvl; + int maint_a_chg_timer_h; + int maint_b_cur_lvl; + int maint_b_vol_lvl; + int maint_b_chg_timer_h; + int low_high_cur_lvl; + int low_high_vol_lvl; + int battery_resistance; + int n_temp_tbl_elements; + const struct abx500_res_to_temp *r_to_t_tbl; + int n_v_cap_tbl_elements; + const struct abx500_v_to_cap *v_to_cap_tbl; + int n_batres_tbl_elements; + const struct batres_vs_temp *batres_tbl; +}; + +/** + * struct abx500_bm_capacity_levels - abx500 capacity level data + * @critical: critical capacity level in percent + * @low: low capacity level in percent + * @normal: normal capacity level in percent + * @high: high capacity level in percent + * @full: full capacity level in percent + */ +struct abx500_bm_capacity_levels { + int critical; + int low; + int normal; + int high; + int full; +}; + +/** + * struct abx500_bm_charger_parameters - Charger specific parameters + * @usb_volt_max: maximum allowed USB charger voltage in mV + * @usb_curr_max: maximum allowed USB charger current in mA + * @ac_volt_max: maximum allowed AC charger voltage in mV + * @ac_curr_max: maximum allowed AC charger current in mA + */ +struct abx500_bm_charger_parameters { + int usb_volt_max; + int usb_curr_max; + int ac_volt_max; + int ac_curr_max; +}; + +/** + * struct abx500_bm_data - abx500 battery management data + * @temp_under under this temp, charging is stopped + * @temp_low between this temp and temp_under charging is reduced + * @temp_high between this temp and temp_over charging is reduced + * @temp_over over this temp, charging is stopped + * @temp_now present battery temperature + * @temp_interval_chg temperature measurement interval in s when charging + * @temp_interval_nochg temperature measurement interval in s when not charging + * @main_safety_tmr_h safety timer for main charger + * @usb_safety_tmr_h safety timer for usb charger + * @bkup_bat_v voltage which we charge the backup battery with + * @bkup_bat_i current which we charge the backup battery with + * @no_maintenance indicates that maintenance charging is disabled + * @capacity_scaling indicates whether capacity scaling is to be used + * @abx500_adc_therm placement of thermistor, batctrl or battemp adc + * @chg_unknown_bat flag to enable charging of unknown batteries + * @enable_overshoot flag to enable VBAT overshoot control + * @auto_trig flag to enable auto adc trigger + * @fg_res resistance of FG resistor in 0.1mOhm + * @n_btypes number of elements in array bat_type + * @batt_id index of the identified battery in array bat_type + * @interval_charging charge alg cycle period time when charging (sec) + * @interval_not_charging charge alg cycle period time when not charging (sec) + * @temp_hysteresis temperature hysteresis + * @gnd_lift_resistance Battery ground to phone ground resistance (mOhm) + * @n_chg_out_curr number of elements in array chg_output_curr + * @n_chg_in_curr number of elements in array chg_input_curr + * @chg_output_curr charger output current level map + * @chg_input_curr charger input current level map + * @maxi maximization parameters + * @cap_levels capacity in percent for the different capacity levels + * @bat_type table of supported battery types + * @chg_params charger parameters + * @fg_params fuel gauge parameters + */ +struct abx500_bm_data { + int temp_under; + int temp_low; + int temp_high; + int temp_over; + int temp_now; + int temp_interval_chg; + int temp_interval_nochg; + int main_safety_tmr_h; + int usb_safety_tmr_h; + int bkup_bat_v; + int bkup_bat_i; + bool autopower_cfg; + bool ac_enabled; + bool usb_enabled; + bool no_maintenance; + bool capacity_scaling; + bool chg_unknown_bat; + bool enable_overshoot; + bool auto_trig; + enum abx500_adc_therm adc_therm; + int fg_res; + int n_btypes; + int batt_id; + int interval_charging; + int interval_not_charging; + int temp_hysteresis; + int gnd_lift_resistance; + int n_chg_out_curr; + int n_chg_in_curr; + int *chg_output_curr; + int *chg_input_curr; + const struct abx500_maxim_parameters *maxi; + const struct abx500_bm_capacity_levels *cap_levels; + struct abx500_battery_type *bat_type; + const struct abx500_bm_charger_parameters *chg_params; + const struct abx500_fg_parameters *fg_params; +}; + +enum { + NTC_EXTERNAL = 0, + NTC_INTERNAL, +}; + /** * struct res_to_temp - defines one point in a temp to res curve. To * be used in battery packs that combines the identification resistor with a @@ -452,25 +717,17 @@ struct ab8500_bm_data { const struct ab8500_fg_parameters *fg_params; }; -struct ab8500_btemp; -struct ab8500_gpadc; -struct ab8500_fg; - -#ifdef CONFIG_AB8500_BM extern struct abx500_bm_data ab8500_bm_data; void ab8500_charger_usb_state_changed(u8 bm_usb_state, u16 mA); -struct ab8500_btemp *ab8500_btemp_get(void); -int ab8500_btemp_get_batctrl_temp(struct ab8500_btemp *btemp); -int ab8500_btemp_get_temp(struct ab8500_btemp *btemp); struct ab8500_fg *ab8500_fg_get(void); int ab8500_fg_inst_curr_blocking(struct ab8500_fg *dev); int ab8500_fg_inst_curr_start(struct ab8500_fg *di); int ab8500_fg_inst_curr_finalize(struct ab8500_fg *di, int *res); int ab8500_fg_inst_curr_started(struct ab8500_fg *di); int ab8500_fg_inst_curr_done(struct ab8500_fg *di); +int ab8500_bm_of_probe(struct device *dev, + struct device_node *np, + struct abx500_bm_data *bm); -#else -static struct abx500_bm_data ab8500_bm_data; -#endif -#endif /* _AB8500_BM_H */ +#endif /* _AB8500_CHARGER_H_ */ diff --git a/include/linux/mfd/abx500/ux500_chargalg.h b/drivers/power/supply/ab8500-chargalg.h similarity index 93% rename from include/linux/mfd/abx500/ux500_chargalg.h rename to drivers/power/supply/ab8500-chargalg.h index 9b97d28..94a6f90 100644 --- a/include/linux/mfd/abx500/ux500_chargalg.h +++ b/drivers/power/supply/ab8500-chargalg.h @@ -4,8 +4,8 @@ * Author: Johan Gardsmark for ST-Ericsson. */ -#ifndef _UX500_CHARGALG_H -#define _UX500_CHARGALG_H +#ifndef _AB8500_CHARGALG_H_ +#define _AB8500_CHARGALG_H_ #include @@ -48,4 +48,4 @@ struct ux500_charger { extern struct blocking_notifier_head charger_notifier_list; -#endif +#endif /* _AB8500_CHARGALG_H_ */ diff --git a/drivers/power/supply/ab8500_bmdata.c b/drivers/power/supply/ab8500_bmdata.c index f6a6697..c2b8c0b 100644 --- a/drivers/power/supply/ab8500_bmdata.c +++ b/drivers/power/supply/ab8500_bmdata.c @@ -4,7 +4,8 @@ #include #include #include -#include + +#include "ab8500-bm.h" /* * These are the defined batteries that uses a NTC and ID resistor placed diff --git a/drivers/power/supply/ab8500_btemp.c b/drivers/power/supply/ab8500_btemp.c index d203453..fdfcd59 100644 --- a/drivers/power/supply/ab8500_btemp.c +++ b/drivers/power/supply/ab8500_btemp.c @@ -25,9 +25,10 @@ #include #include #include -#include #include +#include "ab8500-bm.h" + #define VTVOUT_V 1800 #define BTEMP_THERMAL_LOW_LIMIT -10 @@ -120,16 +121,6 @@ static enum power_supply_property ab8500_btemp_props[] = { static LIST_HEAD(ab8500_btemp_list); /** - * ab8500_btemp_get() - returns a reference to the primary AB8500 BTEMP - * (i.e. the first BTEMP in the instance list) - */ -struct ab8500_btemp *ab8500_btemp_get(void) -{ - return list_first_entry(&ab8500_btemp_list, struct ab8500_btemp, node); -} -EXPORT_SYMBOL(ab8500_btemp_get); - -/** * ab8500_btemp_batctrl_volt_to_res() - convert batctrl voltage to resistance * @di: pointer to the ab8500_btemp structure * @v_batctrl: measured batctrl voltage @@ -754,7 +745,7 @@ static void ab8500_btemp_periodic(struct ab8500_btemp *di, * * Returns battery temperature */ -int ab8500_btemp_get_temp(struct ab8500_btemp *di) +static int ab8500_btemp_get_temp(struct ab8500_btemp *di) { int temp = 0; @@ -790,19 +781,6 @@ int ab8500_btemp_get_temp(struct ab8500_btemp *di) } return temp; } -EXPORT_SYMBOL(ab8500_btemp_get_temp); - -/** - * ab8500_btemp_get_batctrl_temp() - get the temperature - * @btemp: pointer to the btemp structure - * - * Returns the batctrl temperature in millidegrees - */ -int ab8500_btemp_get_batctrl_temp(struct ab8500_btemp *btemp) -{ - return btemp->bat_temp * 1000; -} -EXPORT_SYMBOL(ab8500_btemp_get_batctrl_temp); /** * ab8500_btemp_get_property() - get the btemp properties @@ -991,7 +969,6 @@ static const struct power_supply_desc ab8500_btemp_desc = { static int ab8500_btemp_probe(struct platform_device *pdev) { struct device_node *np = pdev->dev.of_node; - struct abx500_bm_data *plat = pdev->dev.platform_data; struct power_supply_config psy_cfg = {}; struct device *dev = &pdev->dev; struct ab8500_btemp *di; @@ -1002,18 +979,12 @@ static int ab8500_btemp_probe(struct platform_device *pdev) if (!di) return -ENOMEM; - if (!plat) { - dev_err(dev, "no battery management data supplied\n"); - return -EINVAL; - } - di->bm = plat; + di->bm = &ab8500_bm_data; - if (np) { - ret = ab8500_bm_of_probe(dev, np, di->bm); - if (ret) { - dev_err(dev, "failed to get battery information\n"); - return ret; - } + ret = ab8500_bm_of_probe(dev, np, di->bm); + if (ret) { + dev_err(dev, "failed to get battery information\n"); + return ret; } /* get parent data */ diff --git a/drivers/power/supply/ab8500_charger.c b/drivers/power/supply/ab8500_charger.c index ac77c88..a9be10e 100644 --- a/drivers/power/supply/ab8500_charger.c +++ b/drivers/power/supply/ab8500_charger.c @@ -28,12 +28,13 @@ #include #include #include -#include -#include #include #include #include +#include "ab8500-bm.h" +#include "ab8500-chargalg.h" + /* Charger constants */ #define NO_PW_CONN 0 #define AC_PW_CONN 1 @@ -3344,7 +3345,6 @@ static const struct power_supply_desc ab8500_usb_chg_desc = { static int ab8500_charger_probe(struct platform_device *pdev) { struct device_node *np = pdev->dev.of_node; - struct abx500_bm_data *plat = pdev->dev.platform_data; struct power_supply_config ac_psy_cfg = {}, usb_psy_cfg = {}; struct ab8500_charger *di; int irq, i, charger_status, ret = 0, ch_stat; @@ -3354,21 +3354,14 @@ static int ab8500_charger_probe(struct platform_device *pdev) if (!di) return -ENOMEM; - if (!plat) { - dev_err(dev, "no battery management data supplied\n"); - return -EINVAL; - } - di->bm = plat; + di->bm = &ab8500_bm_data; - if (np) { - ret = ab8500_bm_of_probe(dev, np, di->bm); - if (ret) { - dev_err(dev, "failed to get battery information\n"); - return ret; - } - di->autopower_cfg = of_property_read_bool(np, "autopower_cfg"); - } else - di->autopower_cfg = false; + ret = ab8500_bm_of_probe(dev, np, di->bm); + if (ret) { + dev_err(dev, "failed to get battery information\n"); + return ret; + } + di->autopower_cfg = of_property_read_bool(np, "autopower_cfg"); /* get parent data */ di->dev = dev; diff --git a/drivers/power/supply/ab8500_fg.c b/drivers/power/supply/ab8500_fg.c index 06ff42c..0c7c01a 100644 --- a/drivers/power/supply/ab8500_fg.c +++ b/drivers/power/supply/ab8500_fg.c @@ -31,10 +31,11 @@ #include #include #include -#include #include #include +#include "ab8500-bm.h" + #define MILLI_TO_MICRO 1000 #define FG_LSB_IN_MA 1627 #define QLSB_NANO_AMP_HOURS_X10 1071 @@ -3026,7 +3027,6 @@ static const struct power_supply_desc ab8500_fg_desc = { static int ab8500_fg_probe(struct platform_device *pdev) { struct device_node *np = pdev->dev.of_node; - struct abx500_bm_data *plat = pdev->dev.platform_data; struct power_supply_config psy_cfg = {}; struct device *dev = &pdev->dev; struct ab8500_fg *di; @@ -3037,18 +3037,12 @@ static int ab8500_fg_probe(struct platform_device *pdev) if (!di) return -ENOMEM; - if (!plat) { - dev_err(dev, "no battery management data supplied\n"); - return -EINVAL; - } - di->bm = plat; + di->bm = &ab8500_bm_data; - if (np) { - ret = ab8500_bm_of_probe(dev, np, di->bm); - if (ret) { - dev_err(dev, "failed to get battery information\n"); - return ret; - } + ret = ab8500_bm_of_probe(dev, np, di->bm); + if (ret) { + dev_err(dev, "failed to get battery information\n"); + return ret; } mutex_init(&di->cc_lock); diff --git a/drivers/power/supply/abx500_chargalg.c b/drivers/power/supply/abx500_chargalg.c index a9d84d8..f5b7922 100644 --- a/drivers/power/supply/abx500_chargalg.c +++ b/drivers/power/supply/abx500_chargalg.c @@ -28,10 +28,11 @@ #include #include #include -#include -#include #include +#include "ab8500-bm.h" +#include "ab8500-chargalg.h" + /* Watchdog kick interval */ #define CHG_WD_INTERVAL (6 * HZ) @@ -1980,7 +1981,6 @@ static const struct power_supply_desc abx500_chargalg_desc = { static int abx500_chargalg_probe(struct platform_device *pdev) { struct device_node *np = pdev->dev.of_node; - struct abx500_bm_data *plat = pdev->dev.platform_data; struct power_supply_config psy_cfg = {}; struct abx500_chargalg *di; int ret = 0; @@ -1991,18 +1991,12 @@ static int abx500_chargalg_probe(struct platform_device *pdev) return -ENOMEM; } - if (!plat) { - dev_err(&pdev->dev, "no battery management data supplied\n"); - return -EINVAL; - } - di->bm = plat; + di->bm = &ab8500_bm_data; - if (np) { - ret = ab8500_bm_of_probe(&pdev->dev, np, di->bm); - if (ret) { - dev_err(&pdev->dev, "failed to get battery information\n"); - return ret; - } + ret = ab8500_bm_of_probe(&pdev->dev, np, di->bm); + if (ret) { + dev_err(&pdev->dev, "failed to get battery information\n"); + return ret; } /* get device struct and parent */ diff --git a/drivers/power/supply/act8945a_charger.c b/drivers/power/supply/act8945a_charger.c index 5f3eb69..e9b5f42 100644 --- a/drivers/power/supply/act8945a_charger.c +++ b/drivers/power/supply/act8945a_charger.c @@ -18,7 +18,7 @@ static const char *act8945a_charger_model = "ACT8945A"; static const char *act8945a_charger_manufacturer = "Active-semi"; -/** +/* * ACT8945A Charger Register Map */ diff --git a/drivers/power/supply/axp20x_usb_power.c b/drivers/power/supply/axp20x_usb_power.c index e954970..a1d110f 100644 --- a/drivers/power/supply/axp20x_usb_power.c +++ b/drivers/power/supply/axp20x_usb_power.c @@ -619,8 +619,10 @@ static int axp20x_usb_power_probe(struct platform_device *pdev) if (power->axp20x_id == AXP813_ID) { /* Enable USB Battery Charging specification detection */ - regmap_update_bits(axp20x->regmap, AXP288_BC_GLOBAL, + ret = regmap_update_bits(axp20x->regmap, AXP288_BC_GLOBAL, AXP813_BC_EN, AXP813_BC_EN); + if (ret) + return ret; } psy_cfg.of_node = pdev->dev.of_node; diff --git a/drivers/power/supply/bq256xx_charger.c b/drivers/power/supply/bq256xx_charger.c index 2ab5ba4..f501ecd 100644 --- a/drivers/power/supply/bq256xx_charger.c +++ b/drivers/power/supply/bq256xx_charger.c @@ -202,6 +202,8 @@ enum bq256xx_id { * @client: i2c client structure * @regmap: register map structure * @dev: device structure + * @charger: power supply registered for the charger + * @battery: power supply registered for the battery * @lock: mutex lock structure * * @usb2_phy: usb_phy identifier diff --git a/drivers/power/supply/bq25980_charger.c b/drivers/power/supply/bq25980_charger.c index 530ff40..0008c22 100644 --- a/drivers/power/supply/bq25980_charger.c +++ b/drivers/power/supply/bq25980_charger.c @@ -606,33 +606,6 @@ static int bq25980_get_state(struct bq25980_device *bq, return 0; } -static int bq25980_set_battery_property(struct power_supply *psy, - enum power_supply_property psp, - const union power_supply_propval *val) -{ - struct bq25980_device *bq = power_supply_get_drvdata(psy); - int ret = 0; - - switch (psp) { - case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT: - ret = bq25980_set_const_charge_curr(bq, val->intval); - if (ret) - return ret; - break; - - case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE: - ret = bq25980_set_const_charge_volt(bq, val->intval); - if (ret) - return ret; - break; - - default: - return -EINVAL; - } - - return ret; -} - static int bq25980_get_battery_property(struct power_supply *psy, enum power_supply_property psp, union power_supply_propval *val) @@ -701,6 +674,18 @@ static int bq25980_set_charger_property(struct power_supply *psy, return ret; break; + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT: + ret = bq25980_set_const_charge_curr(bq, val->intval); + if (ret) + return ret; + break; + + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE: + ret = bq25980_set_const_charge_volt(bq, val->intval); + if (ret) + return ret; + break; + default: return -EINVAL; } @@ -922,7 +907,6 @@ static struct power_supply_desc bq25980_battery_desc = { .name = "bq25980-battery", .type = POWER_SUPPLY_TYPE_BATTERY, .get_property = bq25980_get_battery_property, - .set_property = bq25980_set_battery_property, .properties = bq25980_battery_props, .num_properties = ARRAY_SIZE(bq25980_battery_props), .property_is_writeable = bq25980_property_is_writeable, diff --git a/drivers/power/supply/bq27xxx_battery.c b/drivers/power/supply/bq27xxx_battery.c index 4c4a7b1..7e5e24b 100644 --- a/drivers/power/supply/bq27xxx_battery.c +++ b/drivers/power/supply/bq27xxx_battery.c @@ -39,6 +39,7 @@ * https://www.ti.com/product/bq27z561 * https://www.ti.com/product/bq28z610 * https://www.ti.com/product/bq34z100-g1 + * https://www.ti.com/product/bq78z100 */ #include @@ -515,6 +516,27 @@ static u8 [BQ27XXX_REG_DCAP] = 0x3c, [BQ27XXX_REG_AP] = 0x22, BQ27XXX_DM_REG_ROWS, + }, + bq78z100_regs[BQ27XXX_REG_MAX] = { + [BQ27XXX_REG_CTRL] = 0x00, + [BQ27XXX_REG_TEMP] = 0x06, + [BQ27XXX_REG_INT_TEMP] = 0x28, + [BQ27XXX_REG_VOLT] = 0x08, + [BQ27XXX_REG_AI] = 0x14, + [BQ27XXX_REG_FLAGS] = 0x0a, + [BQ27XXX_REG_TTE] = 0x16, + [BQ27XXX_REG_TTF] = 0x18, + [BQ27XXX_REG_TTES] = 0x1c, + [BQ27XXX_REG_TTECP] = INVALID_REG_ADDR, + [BQ27XXX_REG_NAC] = INVALID_REG_ADDR, + [BQ27XXX_REG_RC] = 0x10, + [BQ27XXX_REG_FCC] = 0x12, + [BQ27XXX_REG_CYCT] = 0x2a, + [BQ27XXX_REG_AE] = INVALID_REG_ADDR, + [BQ27XXX_REG_SOC] = 0x2c, + [BQ27XXX_REG_DCAP] = 0x3c, + [BQ27XXX_REG_AP] = 0x22, + BQ27XXX_DM_REG_ROWS, }; static enum power_supply_property bq27000_props[] = { @@ -813,6 +835,26 @@ static enum power_supply_property bq34z100_props[] = { POWER_SUPPLY_PROP_MANUFACTURER, }; +static enum power_supply_property bq78z100_props[] = { + POWER_SUPPLY_PROP_STATUS, + POWER_SUPPLY_PROP_PRESENT, + POWER_SUPPLY_PROP_VOLTAGE_NOW, + POWER_SUPPLY_PROP_CURRENT_NOW, + POWER_SUPPLY_PROP_CAPACITY, + POWER_SUPPLY_PROP_CAPACITY_LEVEL, + POWER_SUPPLY_PROP_TEMP, + POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW, + POWER_SUPPLY_PROP_TIME_TO_FULL_NOW, + POWER_SUPPLY_PROP_TECHNOLOGY, + POWER_SUPPLY_PROP_CHARGE_FULL, + POWER_SUPPLY_PROP_CHARGE_NOW, + POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN, + POWER_SUPPLY_PROP_CYCLE_COUNT, + POWER_SUPPLY_PROP_POWER_AVG, + POWER_SUPPLY_PROP_HEALTH, + POWER_SUPPLY_PROP_MANUFACTURER, +}; + struct bq27xxx_dm_reg { u8 subclass_id; u8 offset; @@ -911,6 +953,7 @@ static struct bq27xxx_dm_reg bq27621_dm_regs[] = { #define bq27z561_dm_regs 0 #define bq28z610_dm_regs 0 #define bq34z100_dm_regs 0 +#define bq78z100_dm_regs 0 #define BQ27XXX_O_ZERO BIT(0) #define BQ27XXX_O_OTDC BIT(1) /* has OTC/OTD overtemperature flags */ @@ -969,6 +1012,7 @@ static struct { [BQ28Z610] = BQ27XXX_DATA(bq28z610, 0 , BQ27Z561_O_BITS), [BQ34Z100] = BQ27XXX_DATA(bq34z100, 0 , BQ27XXX_O_OTDC | BQ27XXX_O_SOC_SI | \ BQ27XXX_O_HAS_CI | BQ27XXX_O_MUL_CHEM), + [BQ78Z100] = BQ27XXX_DATA(bq78z100, 0 , BQ27Z561_O_BITS), }; static DEFINE_MUTEX(bq27xxx_list_lock); @@ -1662,27 +1706,6 @@ static int bq27xxx_battery_read_time(struct bq27xxx_device_info *di, u8 reg) } /* - * Read an average power register. - * Return < 0 if something fails. - */ -static int bq27xxx_battery_read_pwr_avg(struct bq27xxx_device_info *di) -{ - int tval; - - tval = bq27xxx_read(di, BQ27XXX_REG_AP, false); - if (tval < 0) { - dev_err(di->dev, "error reading average power register %02x: %d\n", - BQ27XXX_REG_AP, tval); - return tval; - } - - if (di->opts & BQ27XXX_O_ZERO) - return (tval * BQ27XXX_POWER_CONSTANT) / BQ27XXX_RS; - else - return tval; -} - -/* * Returns true if a battery over temperature condition is detected */ static bool bq27xxx_battery_overtemp(struct bq27xxx_device_info *di, u16 flags) @@ -1769,8 +1792,6 @@ void bq27xxx_battery_update(struct bq27xxx_device_info *di) } if (di->regs[BQ27XXX_REG_CYCT] != INVALID_REG_ADDR) cache.cycle_count = bq27xxx_battery_read_cyct(di); - if (di->regs[BQ27XXX_REG_AP] != INVALID_REG_ADDR) - cache.power_avg = bq27xxx_battery_read_pwr_avg(di); /* We only have to read charge design full once */ if (di->charge_design_full <= 0) @@ -1800,14 +1821,27 @@ static void bq27xxx_battery_poll(struct work_struct *work) schedule_delayed_work(&di->work, poll_interval * HZ); } +static bool bq27xxx_battery_is_full(struct bq27xxx_device_info *di, int flags) +{ + if (di->opts & BQ27XXX_O_ZERO) + return (flags & BQ27000_FLAG_FC); + else if (di->opts & BQ27Z561_O_BITS) + return (flags & BQ27Z561_FLAG_FC); + else + return (flags & BQ27XXX_FLAG_FC); +} + /* - * Return the battery average current in µA + * Return the battery average current in µA and the status * Note that current can be negative signed as well * Or 0 if something fails. */ -static int bq27xxx_battery_current(struct bq27xxx_device_info *di, - union power_supply_propval *val) +static int bq27xxx_battery_current_and_status( + struct bq27xxx_device_info *di, + union power_supply_propval *val_curr, + union power_supply_propval *val_status) { + bool single_flags = (di->opts & BQ27XXX_O_ZERO); int curr; int flags; @@ -1817,55 +1851,66 @@ static int bq27xxx_battery_current(struct bq27xxx_device_info *di, return curr; } + flags = bq27xxx_read(di, BQ27XXX_REG_FLAGS, single_flags); + if (flags < 0) { + dev_err(di->dev, "error reading flags\n"); + return flags; + } + if (di->opts & BQ27XXX_O_ZERO) { - flags = bq27xxx_read(di, BQ27XXX_REG_FLAGS, true); if (!(flags & BQ27000_FLAG_CHGS)) { dev_dbg(di->dev, "negative current!\n"); curr = -curr; } - val->intval = curr * BQ27XXX_CURRENT_CONSTANT / BQ27XXX_RS; + curr = curr * BQ27XXX_CURRENT_CONSTANT / BQ27XXX_RS; } else { /* Other gauges return signed value */ - val->intval = -(int)((s16)curr) * 1000; + curr = (int)((s16)curr) * 1000; + } + + if (val_curr) + val_curr->intval = curr; + + if (val_status) { + if (curr > 0) { + val_status->intval = POWER_SUPPLY_STATUS_CHARGING; + } else if (curr < 0) { + val_status->intval = POWER_SUPPLY_STATUS_DISCHARGING; + } else { + if (bq27xxx_battery_is_full(di, flags)) + val_status->intval = POWER_SUPPLY_STATUS_FULL; + else + val_status->intval = + POWER_SUPPLY_STATUS_NOT_CHARGING; + } } return 0; } -static int bq27xxx_battery_status(struct bq27xxx_device_info *di, - union power_supply_propval *val) +/* + * Get the average power in µW + * Return < 0 if something fails. + */ +static int bq27xxx_battery_pwr_avg(struct bq27xxx_device_info *di, + union power_supply_propval *val) { - int status; - - if (di->opts & BQ27XXX_O_ZERO) { - if (di->cache.flags & BQ27000_FLAG_FC) - status = POWER_SUPPLY_STATUS_FULL; - else if (di->cache.flags & BQ27000_FLAG_CHGS) - status = POWER_SUPPLY_STATUS_CHARGING; - else - status = POWER_SUPPLY_STATUS_DISCHARGING; - } else if (di->opts & BQ27Z561_O_BITS) { - if (di->cache.flags & BQ27Z561_FLAG_FC) - status = POWER_SUPPLY_STATUS_FULL; - else if (di->cache.flags & BQ27Z561_FLAG_DIS_CH) - status = POWER_SUPPLY_STATUS_DISCHARGING; - else - status = POWER_SUPPLY_STATUS_CHARGING; - } else { - if (di->cache.flags & BQ27XXX_FLAG_FC) - status = POWER_SUPPLY_STATUS_FULL; - else if (di->cache.flags & BQ27XXX_FLAG_DSC) - status = POWER_SUPPLY_STATUS_DISCHARGING; - else - status = POWER_SUPPLY_STATUS_CHARGING; + int power; + + power = bq27xxx_read(di, BQ27XXX_REG_AP, false); + if (power < 0) { + dev_err(di->dev, + "error reading average power register %02x: %d\n", + BQ27XXX_REG_AP, power); + return power; } - if ((status == POWER_SUPPLY_STATUS_DISCHARGING) && - (power_supply_am_i_supplied(di->bat) > 0)) - status = POWER_SUPPLY_STATUS_NOT_CHARGING; - - val->intval = status; + if (di->opts & BQ27XXX_O_ZERO) + val->intval = (power * BQ27XXX_POWER_CONSTANT) / BQ27XXX_RS; + else + /* Other gauges return a signed value in units of 10mW */ + val->intval = (int)((s16)power) * 10000; return 0; } @@ -1957,7 +2002,7 @@ static int bq27xxx_battery_get_property(struct power_supply *psy, switch (psp) { case POWER_SUPPLY_PROP_STATUS: - ret = bq27xxx_battery_status(di, val); + ret = bq27xxx_battery_current_and_status(di, NULL, val); break; case POWER_SUPPLY_PROP_VOLTAGE_NOW: ret = bq27xxx_battery_voltage(di, val); @@ -1966,7 +2011,7 @@ static int bq27xxx_battery_get_property(struct power_supply *psy, val->intval = di->cache.flags < 0 ? 0 : 1; break; case POWER_SUPPLY_PROP_CURRENT_NOW: - ret = bq27xxx_battery_current(di, val); + ret = bq27xxx_battery_current_and_status(di, val, NULL); break; case POWER_SUPPLY_PROP_CAPACITY: ret = bq27xxx_simple_value(di->cache.capacity, val); @@ -2020,7 +2065,7 @@ static int bq27xxx_battery_get_property(struct power_supply *psy, ret = bq27xxx_simple_value(di->cache.energy, val); break; case POWER_SUPPLY_PROP_POWER_AVG: - ret = bq27xxx_simple_value(di->cache.power_avg, val); + ret = bq27xxx_battery_pwr_avg(di, val); break; case POWER_SUPPLY_PROP_HEALTH: ret = bq27xxx_simple_value(di->cache.health, val); diff --git a/drivers/power/supply/bq27xxx_battery_i2c.c b/drivers/power/supply/bq27xxx_battery_i2c.c index eb4f428..46f0783 100644 --- a/drivers/power/supply/bq27xxx_battery_i2c.c +++ b/drivers/power/supply/bq27xxx_battery_i2c.c @@ -248,6 +248,7 @@ static const struct i2c_device_id bq27xxx_i2c_id_table[] = { { "bq27z561", BQ27Z561 }, { "bq28z610", BQ28Z610 }, { "bq34z100", BQ34Z100 }, + { "bq78z100", BQ78Z100 }, {}, }; MODULE_DEVICE_TABLE(i2c, bq27xxx_i2c_id_table); @@ -284,6 +285,7 @@ static const struct of_device_id bq27xxx_battery_i2c_of_match_table[] = { { .compatible = "ti,bq27z561" }, { .compatible = "ti,bq28z610" }, { .compatible = "ti,bq34z100" }, + { .compatible = "ti,bq78z100" }, {}, }; MODULE_DEVICE_TABLE(of, bq27xxx_battery_i2c_of_match_table); diff --git a/drivers/power/supply/charger-manager.c b/drivers/power/supply/charger-manager.c index 4dea8ec..45da870 100644 --- a/drivers/power/supply/charger-manager.c +++ b/drivers/power/supply/charger-manager.c @@ -1604,7 +1604,7 @@ static int charger_manager_probe(struct platform_device *pdev) mutex_unlock(&cm_list_mtx); /* - * Charger-manager is capable of waking up the systme from sleep + * Charger-manager is capable of waking up the system from sleep * when event is happened through cm_notify_event() */ device_init_wakeup(&pdev->dev, true); diff --git a/drivers/power/supply/cpcap-battery.c b/drivers/power/supply/cpcap-battery.c index 6d5bcdb..a3fc008 100644 --- a/drivers/power/supply/cpcap-battery.c +++ b/drivers/power/supply/cpcap-battery.c @@ -786,7 +786,7 @@ static irqreturn_t cpcap_battery_irq_thread(int irq, void *data) break; } - if (!d) + if (list_entry_is_head(d, &ddata->irq_list, node)) return IRQ_NONE; latest = cpcap_battery_latest(ddata); diff --git a/drivers/power/supply/cpcap-charger.c b/drivers/power/supply/cpcap-charger.c index 641dcad..df01abc 100644 --- a/drivers/power/supply/cpcap-charger.c +++ b/drivers/power/supply/cpcap-charger.c @@ -318,7 +318,7 @@ static int cpcap_charger_current_to_regval(int microamp) return CPCAP_REG_CRM_ICHRG(0x0); if (miliamp < 177) return CPCAP_REG_CRM_ICHRG(0x1); - if (miliamp > 1596) + if (miliamp >= 1596) return CPCAP_REG_CRM_ICHRG(0xe); res = microamp / 88666; @@ -465,7 +465,7 @@ static bool cpcap_charger_vbus_valid(struct cpcap_charger_ddata *ddata) error = iio_read_channel_processed(channel, &value); if (error >= 0) - return value > 3900 ? true : false; + return value > 3900; dev_err(ddata->dev, "error reading VBUS: %i\n", error); @@ -668,6 +668,9 @@ static void cpcap_usb_detect(struct work_struct *work) return; } + /* Delay for 80ms to avoid vbus bouncing when usb cable is plugged in */ + usleep_range(80000, 120000); + /* Throttle chrgcurr2 interrupt for charger done and retry */ switch (ddata->status) { case POWER_SUPPLY_STATUS_CHARGING: diff --git a/drivers/power/supply/cw2015_battery.c b/drivers/power/supply/cw2015_battery.c index 0146f1b..d110597 100644 --- a/drivers/power/supply/cw2015_battery.c +++ b/drivers/power/supply/cw2015_battery.c @@ -511,6 +511,11 @@ static int cw_battery_get_property(struct power_supply *psy, val->intval = 0; break; + case POWER_SUPPLY_PROP_CHARGE_NOW: + val->intval = cw_bat->battery.charge_full_design_uah; + val->intval = val->intval * cw_bat->soc / 100; + break; + case POWER_SUPPLY_PROP_CURRENT_NOW: if (cw_battery_valid_time_to_empty(cw_bat) && cw_bat->battery.charge_full_design_uah > 0) { @@ -542,6 +547,7 @@ static enum power_supply_property cw_battery_properties[] = { POWER_SUPPLY_PROP_CHARGE_COUNTER, POWER_SUPPLY_PROP_CHARGE_FULL, POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN, + POWER_SUPPLY_PROP_CHARGE_NOW, POWER_SUPPLY_PROP_CURRENT_NOW, }; diff --git a/drivers/power/supply/ds2781_battery.c b/drivers/power/supply/ds2781_battery.c index 3df3c82..05b859b 100644 --- a/drivers/power/supply/ds2781_battery.c +++ b/drivers/power/supply/ds2781_battery.c @@ -626,7 +626,7 @@ static ssize_t ds2781_read_param_eeprom_bin(struct file *filp, struct bin_attribute *bin_attr, char *buf, loff_t off, size_t count) { - struct device *dev = container_of(kobj, struct device, kobj); + struct device *dev = kobj_to_dev(kobj); struct power_supply *psy = to_power_supply(dev); struct ds2781_device_info *dev_info = to_ds2781_device_info(psy); @@ -639,7 +639,7 @@ static ssize_t ds2781_write_param_eeprom_bin(struct file *filp, struct bin_attribute *bin_attr, char *buf, loff_t off, size_t count) { - struct device *dev = container_of(kobj, struct device, kobj); + struct device *dev = kobj_to_dev(kobj); struct power_supply *psy = to_power_supply(dev); struct ds2781_device_info *dev_info = to_ds2781_device_info(psy); int ret; @@ -671,7 +671,7 @@ static ssize_t ds2781_read_user_eeprom_bin(struct file *filp, struct bin_attribute *bin_attr, char *buf, loff_t off, size_t count) { - struct device *dev = container_of(kobj, struct device, kobj); + struct device *dev = kobj_to_dev(kobj); struct power_supply *psy = to_power_supply(dev); struct ds2781_device_info *dev_info = to_ds2781_device_info(psy); @@ -685,7 +685,7 @@ static ssize_t ds2781_write_user_eeprom_bin(struct file *filp, struct bin_attribute *bin_attr, char *buf, loff_t off, size_t count) { - struct device *dev = container_of(kobj, struct device, kobj); + struct device *dev = kobj_to_dev(kobj); struct power_supply *psy = to_power_supply(dev); struct ds2781_device_info *dev_info = to_ds2781_device_info(psy); int ret; diff --git a/drivers/power/supply/generic-adc-battery.c b/drivers/power/supply/generic-adc-battery.c index 0032069..66039c6 100644 --- a/drivers/power/supply/generic-adc-battery.c +++ b/drivers/power/supply/generic-adc-battery.c @@ -373,7 +373,7 @@ static int gab_remove(struct platform_device *pdev) } kfree(adc_bat->psy_desc.properties); - cancel_delayed_work(&adc_bat->bat_work); + cancel_delayed_work_sync(&adc_bat->bat_work); return 0; } diff --git a/drivers/power/supply/lp8788-charger.c b/drivers/power/supply/lp8788-charger.c index e7931ff..397e5a0 100644 --- a/drivers/power/supply/lp8788-charger.c +++ b/drivers/power/supply/lp8788-charger.c @@ -501,7 +501,7 @@ static int lp8788_set_irqs(struct platform_device *pdev, ret = request_threaded_irq(virq, NULL, lp8788_charger_irq_thread, - 0, name, pchg); + IRQF_ONESHOT, name, pchg); if (ret) break; } diff --git a/drivers/power/supply/max14577_charger.c b/drivers/power/supply/max14577_charger.c index dcedae1..f244cd9 100644 --- a/drivers/power/supply/max14577_charger.c +++ b/drivers/power/supply/max14577_charger.c @@ -261,7 +261,7 @@ static int max14577_init_constant_voltage(struct max14577_charger *chg, static int max14577_init_eoc(struct max14577_charger *chg, unsigned int uamp) { - unsigned int current_bits = 0xf; + unsigned int current_bits; u8 reg_data; switch (chg->max14577->dev_type) { diff --git a/drivers/power/supply/max17040_battery.c b/drivers/power/supply/max17040_battery.c index d956c67..1aab868 100644 --- a/drivers/power/supply/max17040_battery.c +++ b/drivers/power/supply/max17040_battery.c @@ -268,11 +268,10 @@ static int max17040_get_of_data(struct max17040_chip *chip) rcomp_len = device_property_count_u8(dev, "maxim,rcomp"); chip->rcomp = MAX17040_RCOMP_DEFAULT; if (rcomp_len == data->rcomp_bytes) { - device_property_read_u8_array(dev, "maxim,rcomp", - rcomp, rcomp_len); - chip->rcomp = rcomp_len == 2 ? - rcomp[0] << 8 | rcomp[1] : - rcomp[0] << 8; + if (!device_property_read_u8_array(dev, "maxim,rcomp", + rcomp, rcomp_len)) + chip->rcomp = rcomp_len == 2 ? rcomp[0] << 8 | rcomp[1] : + rcomp[0] << 8; } else if (rcomp_len > 0) { dev_err(dev, "maxim,rcomp has incorrect length\n"); return -EINVAL; @@ -487,8 +486,7 @@ static int max17040_probe(struct i2c_client *client, ret = max17040_get_of_data(chip); if (ret) return ret; - chip_id = (enum chip_id) (uintptr_t) - of_device_get_match_data(&client->dev); + chip_id = (uintptr_t)of_device_get_match_data(&client->dev); } chip->data = max17040_family[chip_id]; diff --git a/drivers/power/supply/max17042_battery.c b/drivers/power/supply/max17042_battery.c index 79d4b59..1d7326c 100644 --- a/drivers/power/supply/max17042_battery.c +++ b/drivers/power/supply/max17042_battery.c @@ -131,7 +131,7 @@ static int max17042_get_status(struct max17042_chip *chip, int *status) * * When this cycle the battery gets charged to a higher (calculated) * capacity then the previous cycle then FullCAP will get updated - * contineously once end-of-charge detection kicks in, so allow the + * continuously once end-of-charge detection kicks in, so allow the * 2 to differ a bit. */ @@ -739,7 +739,7 @@ static void max17042_load_new_capacity_params(struct max17042_chip *chip) /* * Block write all the override values coming from platform data. - * This function MUST be called before the POR initialization proceedure + * This function MUST be called before the POR initialization procedure * specified by maxim. */ static inline void max17042_override_por_values(struct max17042_chip *chip) @@ -811,7 +811,7 @@ static int max17042_init_chip(struct max17042_chip *chip) */ msleep(500); - /* Initialize configaration */ + /* Initialize configuration */ max17042_write_config_regs(chip); /* write cell characterization data */ @@ -855,7 +855,7 @@ static void max17042_set_soc_threshold(struct max17042_chip *chip, u16 off) struct regmap *map = chip->regmap; u32 soc, soc_tr; - /* program interrupt thesholds such that we should + /* program interrupt thresholds such that we should * get interrupt for every 'off' perc change in the soc */ regmap_read(map, MAX17042_RepSOC, &soc); diff --git a/drivers/power/supply/max1721x_battery.c b/drivers/power/supply/max1721x_battery.c index 1b1a36f..473e53c 100644 --- a/drivers/power/supply/max1721x_battery.c +++ b/drivers/power/supply/max1721x_battery.c @@ -1,6 +1,6 @@ /* * 1-Wire implementation for Maxim Semiconductor - * MAX7211/MAX17215 stanalone fuel gauge chip + * MAX7211/MAX17215 standalone fuel gauge chip * * Copyright (C) 2017 Radioavionica Corporation * Author: Alex A. Mihaylov @@ -28,7 +28,7 @@ /* Number of valid register addresses in W1 mode */ #define MAX1721X_MAX_REG_NR 0x1EF -/* Factory settings (nonvilatile registers) (W1 specific) */ +/* Factory settings (nonvolatile registers) (W1 specific) */ #define MAX1721X_REG_NRSENSE 0x1CF /* RSense in 10^-5 Ohm */ /* Strings */ #define MAX1721X_REG_MFG_STR 0x1CC @@ -105,7 +105,7 @@ static inline int max172xx_temperature_to_ps(unsigned int reg) /* * Calculating current registers resolution: * - * RSense stored in 10^-5 Ohm, so mesaurment voltage must be + * RSense stored in 10^-5 Ohm, so measurement voltage must be * in 10^-11 Volts for get current in uA. * 16 bit current reg fullscale +/-51.2mV is 102400 uV. * So: 102400 / 65535 * 10^5 = 156252 @@ -137,7 +137,7 @@ static int max1721x_battery_get_property(struct power_supply *psy, /* * POWER_SUPPLY_PROP_PRESENT will always readable via * sysfs interface. Value return 0 if battery not - * present or unaccesable via W1. + * present or unaccessible via W1. */ val->intval = regmap_read(info->regmap, MAX172XX_REG_STATUS, @@ -334,9 +334,9 @@ static int devm_w1_max1721x_add_device(struct w1_slave *sl) /* * power_supply class battery name translated from W1 slave device - * unical ID (look like 26-0123456789AB) to "max1721x-0123456789AB\0" - * so, 26 (device family) correcpondent to max1721x devices. - * Device name still unical for any numbers connected devices. + * unique ID (look like 26-0123456789AB) to "max1721x-0123456789AB\0" + * so, 26 (device family) correspond to max1721x devices. + * Device name still unique for any number of connected devices. */ snprintf(info->name, sizeof(info->name), "max1721x-%012X", (unsigned int)sl->reg_num.id); diff --git a/drivers/power/supply/max8997_charger.c b/drivers/power/supply/max8997_charger.c index 321bd6b..25207fe 100644 --- a/drivers/power/supply/max8997_charger.c +++ b/drivers/power/supply/max8997_charger.c @@ -168,6 +168,7 @@ static int max8997_battery_probe(struct platform_device *pdev) int ret = 0; struct charger_data *charger; struct max8997_dev *iodev = dev_get_drvdata(pdev->dev.parent); + struct device_node *np = pdev->dev.of_node; struct i2c_client *i2c = iodev->i2c; struct max8997_platform_data *pdata = iodev->pdata; struct power_supply_config psy_cfg = {}; @@ -237,20 +238,23 @@ static int max8997_battery_probe(struct platform_device *pdev) return PTR_ERR(charger->battery); } + // grab regulator from parent device's node + pdev->dev.of_node = iodev->dev->of_node; charger->reg = devm_regulator_get_optional(&pdev->dev, "charger"); + pdev->dev.of_node = np; if (IS_ERR(charger->reg)) { if (PTR_ERR(charger->reg) == -EPROBE_DEFER) return -EPROBE_DEFER; dev_info(&pdev->dev, "couldn't get charger regulator\n"); } - charger->edev = extcon_get_edev_by_phandle(&pdev->dev, 0); - if (IS_ERR(charger->edev)) { - if (PTR_ERR(charger->edev) == -EPROBE_DEFER) + charger->edev = extcon_get_extcon_dev("max8997-muic"); + if (IS_ERR_OR_NULL(charger->edev)) { + if (!charger->edev) return -EPROBE_DEFER; dev_info(charger->dev, "couldn't get extcon device\n"); } - if (!IS_ERR(charger->reg) && !IS_ERR(charger->edev)) { + if (!IS_ERR(charger->reg) && !IS_ERR_OR_NULL(charger->edev)) { INIT_WORK(&charger->extcon_work, max8997_battery_extcon_evt_worker); ret = devm_add_action(&pdev->dev, max8997_battery_extcon_evt_stop_work, charger); if (ret) { @@ -263,7 +267,7 @@ static int max8997_battery_probe(struct platform_device *pdev) if (ret) { dev_err(&pdev->dev, "failed to register extcon notifier\n"); return ret; - }; + } } return 0; diff --git a/drivers/power/supply/pm2301_charger.c b/drivers/power/supply/pm2301_charger.c index ac06ecf..f86bbbe 100644 --- a/drivers/power/supply/pm2301_charger.c +++ b/drivers/power/supply/pm2301_charger.c @@ -18,13 +18,13 @@ #include #include #include -#include -#include #include #include #include #include +#include "ab8500-bm.h" +#include "ab8500-chargalg.h" #include "pm2301_charger.h" #define to_pm2xxx_charger_ac_device_info(x) container_of((x), \ @@ -1089,7 +1089,7 @@ static int pm2xxx_wall_charger_probe(struct i2c_client *i2c_client, ret = request_threaded_irq(gpio_to_irq(pm2->pdata->gpio_irq_number), NULL, pm2xxx_charger_irq[0].isr, - pm2->pdata->irq_type, + pm2->pdata->irq_type | IRQF_ONESHOT, pm2xxx_charger_irq[0].name, pm2); if (ret != 0) { diff --git a/drivers/power/supply/power_supply_core.c b/drivers/power/supply/power_supply_core.c index 38e3aa6..d99e2f1 100644 --- a/drivers/power/supply/power_supply_core.c +++ b/drivers/power/supply/power_supply_core.c @@ -169,7 +169,7 @@ static int __power_supply_populate_supplied_from(struct device *dev, break; if (np == epsy->of_node) { - dev_info(&psy->dev, "%s: Found supply : %s\n", + dev_dbg(&psy->dev, "%s: Found supply : %s\n", psy->desc->name, epsy->desc->name); psy->supplied_from[i-1] = (char *)epsy->desc->name; psy->num_supplies++; @@ -1143,7 +1143,7 @@ __power_supply_register(struct device *parent, rc = power_supply_check_supplies(psy); if (rc) { - dev_info(dev, "Not all required supplies found, defer probe\n"); + dev_dbg(dev, "Not all required supplies found, defer probe\n"); goto check_supplies_failed; } diff --git a/drivers/power/supply/s3c_adc_battery.c b/drivers/power/supply/s3c_adc_battery.c index a2addc2..68d31a3 100644 --- a/drivers/power/supply/s3c_adc_battery.c +++ b/drivers/power/supply/s3c_adc_battery.c @@ -1,13 +1,8 @@ -/* - * iPAQ h1930/h1940/rx1950 battery controller driver - * Copyright (c) Vasily Khoruzhick - * Based on h1940_battery.c by Arnaud Patard - * - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file COPYING in the main directory of this archive for - * more details. - * - */ +// SPDX-License-Identifier: GPL-2.0 +// +// iPAQ h1930/h1940/rx1950 battery controller driver +// Copyright (c) Vasily Khoruzhick +// Based on h1940_battery.c by Arnaud Patard #include #include @@ -395,7 +390,7 @@ static int s3c_adc_bat_remove(struct platform_device *pdev) if (main_bat.charge_finished) free_irq(gpiod_to_irq(main_bat.charge_finished), NULL); - cancel_delayed_work(&bat_work); + cancel_delayed_work_sync(&bat_work); if (pdata->exit) pdata->exit(); @@ -407,8 +402,6 @@ static int s3c_adc_bat_remove(struct platform_device *pdev) static int s3c_adc_bat_suspend(struct platform_device *pdev, pm_message_t state) { - struct s3c_adc_bat_pdata *pdata = pdev->dev.platform_data; - if (main_bat.charge_finished) { if (device_may_wakeup(&pdev->dev)) enable_irq_wake( @@ -424,8 +417,6 @@ static int s3c_adc_bat_suspend(struct platform_device *pdev, static int s3c_adc_bat_resume(struct platform_device *pdev) { - struct s3c_adc_bat_pdata *pdata = pdev->dev.platform_data; - if (main_bat.charge_finished) { if (device_may_wakeup(&pdev->dev)) disable_irq_wake( diff --git a/drivers/power/supply/sbs-battery.c b/drivers/power/supply/sbs-battery.c index 70ea404..8d7a107 100644 --- a/drivers/power/supply/sbs-battery.c +++ b/drivers/power/supply/sbs-battery.c @@ -1124,11 +1124,9 @@ static int sbs_probe(struct i2c_client *client) chip->gpio_detect = devm_gpiod_get_optional(&client->dev, "sbs,battery-detect", GPIOD_IN); - if (IS_ERR(chip->gpio_detect)) { - dev_err(&client->dev, "Failed to get gpio: %ld\n", - PTR_ERR(chip->gpio_detect)); - return PTR_ERR(chip->gpio_detect); - } + if (IS_ERR(chip->gpio_detect)) + return dev_err_probe(&client->dev, PTR_ERR(chip->gpio_detect), + "Failed to get gpio\n"); i2c_set_clientdata(client, chip); @@ -1159,11 +1157,9 @@ skip_gpio: rc = sbs_get_battery_presence_and_health( client, POWER_SUPPLY_PROP_PRESENT, &val); - if (rc < 0 || !val.intval) { - dev_err(&client->dev, "Failed to get present status\n"); - rc = -ENODEV; - goto exit_psupply; - } + if (rc < 0 || !val.intval) + return dev_err_probe(&client->dev, -ENODEV, + "Failed to get present status\n"); } rc = devm_delayed_work_autocancel(&client->dev, &chip->work, @@ -1173,20 +1169,14 @@ skip_gpio: chip->power_supply = devm_power_supply_register(&client->dev, sbs_desc, &psy_cfg); - if (IS_ERR(chip->power_supply)) { - dev_err(&client->dev, - "%s: Failed to register power supply\n", __func__); - rc = PTR_ERR(chip->power_supply); - goto exit_psupply; - } + if (IS_ERR(chip->power_supply)) + return dev_err_probe(&client->dev, PTR_ERR(chip->power_supply), + "Failed to register power supply\n"); dev_info(&client->dev, "%s: battery gas gauge device registered\n", client->name); return 0; - -exit_psupply: - return rc; } #if defined CONFIG_PM_SLEEP diff --git a/drivers/power/supply/sbs-charger.c b/drivers/power/supply/sbs-charger.c index fbfb6a6..6fa65d1 100644 --- a/drivers/power/supply/sbs-charger.c +++ b/drivers/power/supply/sbs-charger.c @@ -16,9 +16,7 @@ #include #include #include -#include #include -#include #include #define SBS_CHARGER_REG_SPEC_INFO 0x11 @@ -189,18 +187,14 @@ static int sbs_probe(struct i2c_client *client, * to the battery. */ ret = regmap_read(chip->regmap, SBS_CHARGER_REG_STATUS, &val); - if (ret) { - dev_err(&client->dev, "Failed to get device status\n"); - return ret; - } + if (ret) + return dev_err_probe(&client->dev, ret, "Failed to get device status\n"); chip->last_state = val; - chip->power_supply = devm_power_supply_register(&client->dev, &sbs_desc, - &psy_cfg); - if (IS_ERR(chip->power_supply)) { - dev_err(&client->dev, "Failed to register power supply\n"); - return PTR_ERR(chip->power_supply); - } + chip->power_supply = devm_power_supply_register(&client->dev, &sbs_desc, &psy_cfg); + if (IS_ERR(chip->power_supply)) + return dev_err_probe(&client->dev, PTR_ERR(chip->power_supply), + "Failed to register power supply\n"); /* * The sbs-charger spec doesn't impose the use of an interrupt. So in @@ -212,10 +206,8 @@ static int sbs_probe(struct i2c_client *client, NULL, sbs_irq_thread, IRQF_TRIGGER_FALLING | IRQF_ONESHOT, dev_name(&client->dev), chip); - if (ret) { - dev_err(&client->dev, "Failed to request irq, %d\n", ret); - return ret; - } + if (ret) + return dev_err_probe(&client->dev, ret, "Failed to request irq\n"); } else { INIT_DELAYED_WORK(&chip->work, sbs_delayed_work); schedule_delayed_work(&chip->work, diff --git a/drivers/power/supply/sbs-manager.c b/drivers/power/supply/sbs-manager.c index 666243d..71ec8f7 100644 --- a/drivers/power/supply/sbs-manager.c +++ b/drivers/power/supply/sbs-manager.c @@ -13,7 +13,7 @@ * Karl-Heinz Schneider */ -#include +#include #include #include #include @@ -294,10 +294,8 @@ static int sbsm_gpio_setup(struct sbsm_data *data) gc->owner = THIS_MODULE; ret = devm_gpiochip_add_data(dev, gc, data); - if (ret) { - dev_err(dev, "devm_gpiochip_add_data failed: %d\n", ret); - return ret; - } + if (ret) + return dev_err_probe(dev, ret, "devm_gpiochip_add_data failed\n"); return ret; } @@ -311,6 +309,12 @@ static const struct power_supply_desc sbsm_default_psy_desc = { .property_is_writeable = &sbsm_prop_is_writeable, }; +static void sbsm_del_mux_adapter(void *data) +{ + struct sbsm_data *sbsm = data; + i2c_mux_del_adapters(sbsm->muxc); +} + static int sbsm_probe(struct i2c_client *client, const struct i2c_device_id *id) { @@ -343,13 +347,14 @@ static int sbsm_probe(struct i2c_client *client, data->supported_bats = ret & SBSM_MASK_BAT_SUPPORTED; data->muxc = i2c_mux_alloc(adapter, dev, SBSM_MAX_BATS, 0, I2C_MUX_LOCKED, &sbsm_select, NULL); - if (!data->muxc) { - dev_err(dev, "failed to alloc i2c mux\n"); - ret = -ENOMEM; - goto err_mux_alloc; - } + if (!data->muxc) + return dev_err_probe(dev, -ENOMEM, "failed to alloc i2c mux\n"); data->muxc->priv = data; + ret = devm_add_action_or_reset(dev, sbsm_del_mux_adapter, data); + if (ret) + return ret; + /* register muxed i2c channels. One for each supported battery */ for (i = 0; i < SBSM_MAX_BATS; ++i) { if (data->supported_bats & BIT(i)) { @@ -358,54 +363,28 @@ static int sbsm_probe(struct i2c_client *client, break; } } - if (ret) { - dev_err(dev, "failed to register i2c mux channel %d\n", i + 1); - goto err_mux_register; - } + if (ret) + return dev_err_probe(dev, ret, "failed to register i2c mux channel %d\n", i + 1); - psy_desc = devm_kmemdup(dev, &sbsm_default_psy_desc, - sizeof(struct power_supply_desc), - GFP_KERNEL); - if (!psy_desc) { - ret = -ENOMEM; - goto err_psy; - } + psy_desc = devm_kmemdup(dev, &sbsm_default_psy_desc, sizeof(*psy_desc), GFP_KERNEL); + if (!psy_desc) + return -ENOMEM; + + psy_desc->name = devm_kasprintf(dev, GFP_KERNEL, "sbsm-%s", dev_name(&client->dev)); + if (!psy_desc->name) + return -ENOMEM; - psy_desc->name = devm_kasprintf(dev, GFP_KERNEL, "sbsm-%s", - dev_name(&client->dev)); - if (!psy_desc->name) { - ret = -ENOMEM; - goto err_psy; - } ret = sbsm_gpio_setup(data); if (ret < 0) - goto err_psy; + return ret; psy_cfg.drv_data = data; psy_cfg.of_node = dev->of_node; data->psy = devm_power_supply_register(dev, psy_desc, &psy_cfg); - if (IS_ERR(data->psy)) { - ret = PTR_ERR(data->psy); - dev_err(dev, "failed to register power supply %s\n", - psy_desc->name); - goto err_psy; - } - - return 0; - -err_psy: -err_mux_register: - i2c_mux_del_adapters(data->muxc); - -err_mux_alloc: - return ret; -} - -static int sbsm_remove(struct i2c_client *client) -{ - struct sbsm_data *data = i2c_get_clientdata(client); + if (IS_ERR(data->psy)) + return dev_err_probe(dev, PTR_ERR(data->psy), + "failed to register power supply %s\n", psy_desc->name); - i2c_mux_del_adapters(data->muxc); return 0; } @@ -431,7 +410,6 @@ static struct i2c_driver sbsm_driver = { .of_match_table = of_match_ptr(sbsm_dt_ids), }, .probe = sbsm_probe, - .remove = sbsm_remove, .alert = sbsm_alert, .id_table = sbsm_ids }; diff --git a/drivers/power/supply/smb347-charger.c b/drivers/power/supply/smb347-charger.c index 8cfbd8d..3376f42 100644 --- a/drivers/power/supply/smb347-charger.c +++ b/drivers/power/supply/smb347-charger.c @@ -911,11 +911,14 @@ static int smb347_irq_init(struct smb347_charger *smb, { int ret; - ret = devm_request_threaded_irq(smb->dev, client->irq, NULL, - smb347_interrupt, IRQF_ONESHOT, - client->name, smb); - if (ret < 0) - return ret; + smb->irq_unsupported = true; + + /* + * Interrupt pin is optional. If it is connected, we setup the + * interrupt support here. + */ + if (!client->irq) + return 0; ret = smb347_set_writable(smb, true); if (ret < 0) @@ -931,7 +934,25 @@ static int smb347_irq_init(struct smb347_charger *smb, smb347_set_writable(smb, false); - return ret; + if (ret < 0) { + dev_warn(smb->dev, "failed to initialize IRQ: %d\n", ret); + dev_warn(smb->dev, "disabling IRQ support\n"); + return 0; + } + + ret = devm_request_threaded_irq(smb->dev, client->irq, NULL, + smb347_interrupt, IRQF_ONESHOT, + client->name, smb); + if (ret) + return ret; + + smb->irq_unsupported = false; + + ret = smb347_irq_enable(smb); + if (ret < 0) + return ret; + + return 0; } /* @@ -1120,9 +1141,13 @@ static int smb347_get_property(struct power_supply *psy, struct i2c_client *client = to_i2c_client(smb->dev); int ret; - disable_irq(client->irq); + if (!smb->irq_unsupported) + disable_irq(client->irq); + ret = smb347_get_property_locked(psy, prop, val); - enable_irq(client->irq); + + if (!smb->irq_unsupported) + enable_irq(client->irq); return ret; } @@ -1339,20 +1364,9 @@ static int smb347_probe(struct i2c_client *client, if (ret < 0) return ret; - /* - * Interrupt pin is optional. If it is connected, we setup the - * interrupt support here. - */ - if (client->irq) { - ret = smb347_irq_init(smb, client); - if (ret < 0) { - dev_warn(dev, "failed to initialize IRQ: %d\n", ret); - dev_warn(dev, "disabling IRQ support\n"); - smb->irq_unsupported = true; - } else { - smb347_irq_enable(smb); - } - } + ret = smb347_irq_init(smb, client); + if (ret) + return ret; return 0; } @@ -1387,11 +1401,10 @@ static struct i2c_driver smb347_driver = { .name = "smb347", .of_match_table = smb3xx_of_match, }, - .probe = smb347_probe, - .remove = smb347_remove, - .id_table = smb347_id, + .probe = smb347_probe, + .remove = smb347_remove, + .id_table = smb347_id, }; - module_i2c_driver(smb347_driver); MODULE_AUTHOR("Bruce E. Robertson "); diff --git a/drivers/power/supply/surface_battery.c b/drivers/power/supply/surface_battery.c new file mode 100644 index 0000000..7efa431 --- /dev/null +++ b/drivers/power/supply/surface_battery.c @@ -0,0 +1,865 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Battery driver for 7th-generation Microsoft Surface devices via Surface + * System Aggregator Module (SSAM). + * + * Copyright (C) 2019-2021 Maximilian Luz + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + + +/* -- SAM interface. -------------------------------------------------------- */ + +enum sam_event_cid_bat { + SAM_EVENT_CID_BAT_BIX = 0x15, + SAM_EVENT_CID_BAT_BST = 0x16, + SAM_EVENT_CID_BAT_ADP = 0x17, + SAM_EVENT_CID_BAT_PROT = 0x18, + SAM_EVENT_CID_BAT_DPTF = 0x53, +}; + +enum sam_battery_sta { + SAM_BATTERY_STA_OK = 0x0f, + SAM_BATTERY_STA_PRESENT = 0x10, +}; + +enum sam_battery_state { + SAM_BATTERY_STATE_DISCHARGING = BIT(0), + SAM_BATTERY_STATE_CHARGING = BIT(1), + SAM_BATTERY_STATE_CRITICAL = BIT(2), +}; + +enum sam_battery_power_unit { + SAM_BATTERY_POWER_UNIT_mW = 0, + SAM_BATTERY_POWER_UNIT_mA = 1, +}; + +/* Equivalent to data returned in ACPI _BIX method, revision 0. */ +struct spwr_bix { + u8 revision; + __le32 power_unit; + __le32 design_cap; + __le32 last_full_charge_cap; + __le32 technology; + __le32 design_voltage; + __le32 design_cap_warn; + __le32 design_cap_low; + __le32 cycle_count; + __le32 measurement_accuracy; + __le32 max_sampling_time; + __le32 min_sampling_time; + __le32 max_avg_interval; + __le32 min_avg_interval; + __le32 bat_cap_granularity_1; + __le32 bat_cap_granularity_2; + __u8 model[21]; + __u8 serial[11]; + __u8 type[5]; + __u8 oem_info[21]; +} __packed; + +static_assert(sizeof(struct spwr_bix) == 119); + +/* Equivalent to data returned in ACPI _BST method. */ +struct spwr_bst { + __le32 state; + __le32 present_rate; + __le32 remaining_cap; + __le32 present_voltage; +} __packed; + +static_assert(sizeof(struct spwr_bst) == 16); + +#define SPWR_BIX_REVISION 0 +#define SPWR_BATTERY_VALUE_UNKNOWN 0xffffffff + +/* Get battery status (_STA) */ +SSAM_DEFINE_SYNC_REQUEST_CL_R(ssam_bat_get_sta, __le32, { + .target_category = SSAM_SSH_TC_BAT, + .command_id = 0x01, +}); + +/* Get battery static information (_BIX). */ +SSAM_DEFINE_SYNC_REQUEST_CL_R(ssam_bat_get_bix, struct spwr_bix, { + .target_category = SSAM_SSH_TC_BAT, + .command_id = 0x02, +}); + +/* Get battery dynamic information (_BST). */ +SSAM_DEFINE_SYNC_REQUEST_CL_R(ssam_bat_get_bst, struct spwr_bst, { + .target_category = SSAM_SSH_TC_BAT, + .command_id = 0x03, +}); + +/* Set battery trip point (_BTP). */ +SSAM_DEFINE_SYNC_REQUEST_CL_W(ssam_bat_set_btp, __le32, { + .target_category = SSAM_SSH_TC_BAT, + .command_id = 0x04, +}); + + +/* -- Device structures. ---------------------------------------------------- */ + +struct spwr_psy_properties { + const char *name; + struct ssam_event_registry registry; +}; + +struct spwr_battery_device { + struct ssam_device *sdev; + + char name[32]; + struct power_supply *psy; + struct power_supply_desc psy_desc; + + struct delayed_work update_work; + + struct ssam_event_notifier notif; + + struct mutex lock; /* Guards access to state data below. */ + unsigned long timestamp; + + __le32 sta; + struct spwr_bix bix; + struct spwr_bst bst; + u32 alarm; +}; + + +/* -- Module parameters. ---------------------------------------------------- */ + +static unsigned int cache_time = 1000; +module_param(cache_time, uint, 0644); +MODULE_PARM_DESC(cache_time, "battery state caching time in milliseconds [default: 1000]"); + + +/* -- State management. ----------------------------------------------------- */ + +/* + * Delay for battery update quirk. See spwr_external_power_changed() below + * for more details. + */ +#define SPWR_AC_BAT_UPDATE_DELAY msecs_to_jiffies(5000) + +static bool spwr_battery_present(struct spwr_battery_device *bat) +{ + lockdep_assert_held(&bat->lock); + + return le32_to_cpu(bat->sta) & SAM_BATTERY_STA_PRESENT; +} + +static int spwr_battery_load_sta(struct spwr_battery_device *bat) +{ + lockdep_assert_held(&bat->lock); + + return ssam_retry(ssam_bat_get_sta, bat->sdev, &bat->sta); +} + +static int spwr_battery_load_bix(struct spwr_battery_device *bat) +{ + int status; + + lockdep_assert_held(&bat->lock); + + if (!spwr_battery_present(bat)) + return 0; + + status = ssam_retry(ssam_bat_get_bix, bat->sdev, &bat->bix); + + /* Enforce NULL terminated strings in case anything goes wrong... */ + bat->bix.model[ARRAY_SIZE(bat->bix.model) - 1] = 0; + bat->bix.serial[ARRAY_SIZE(bat->bix.serial) - 1] = 0; + bat->bix.type[ARRAY_SIZE(bat->bix.type) - 1] = 0; + bat->bix.oem_info[ARRAY_SIZE(bat->bix.oem_info) - 1] = 0; + + return status; +} + +static int spwr_battery_load_bst(struct spwr_battery_device *bat) +{ + lockdep_assert_held(&bat->lock); + + if (!spwr_battery_present(bat)) + return 0; + + return ssam_retry(ssam_bat_get_bst, bat->sdev, &bat->bst); +} + +static int spwr_battery_set_alarm_unlocked(struct spwr_battery_device *bat, u32 value) +{ + __le32 value_le = cpu_to_le32(value); + + lockdep_assert_held(&bat->lock); + + bat->alarm = value; + return ssam_retry(ssam_bat_set_btp, bat->sdev, &value_le); +} + +static int spwr_battery_update_bst_unlocked(struct spwr_battery_device *bat, bool cached) +{ + unsigned long cache_deadline = bat->timestamp + msecs_to_jiffies(cache_time); + int status; + + lockdep_assert_held(&bat->lock); + + if (cached && bat->timestamp && time_is_after_jiffies(cache_deadline)) + return 0; + + status = spwr_battery_load_sta(bat); + if (status) + return status; + + status = spwr_battery_load_bst(bat); + if (status) + return status; + + bat->timestamp = jiffies; + return 0; +} + +static int spwr_battery_update_bst(struct spwr_battery_device *bat, bool cached) +{ + int status; + + mutex_lock(&bat->lock); + status = spwr_battery_update_bst_unlocked(bat, cached); + mutex_unlock(&bat->lock); + + return status; +} + +static int spwr_battery_update_bix_unlocked(struct spwr_battery_device *bat) +{ + int status; + + lockdep_assert_held(&bat->lock); + + status = spwr_battery_load_sta(bat); + if (status) + return status; + + status = spwr_battery_load_bix(bat); + if (status) + return status; + + status = spwr_battery_load_bst(bat); + if (status) + return status; + + if (bat->bix.revision != SPWR_BIX_REVISION) + dev_warn(&bat->sdev->dev, "unsupported battery revision: %u\n", bat->bix.revision); + + bat->timestamp = jiffies; + return 0; +} + +static u32 sprw_battery_get_full_cap_safe(struct spwr_battery_device *bat) +{ + u32 full_cap = get_unaligned_le32(&bat->bix.last_full_charge_cap); + + lockdep_assert_held(&bat->lock); + + if (full_cap == 0 || full_cap == SPWR_BATTERY_VALUE_UNKNOWN) + full_cap = get_unaligned_le32(&bat->bix.design_cap); + + return full_cap; +} + +static bool spwr_battery_is_full(struct spwr_battery_device *bat) +{ + u32 state = get_unaligned_le32(&bat->bst.state); + u32 full_cap = sprw_battery_get_full_cap_safe(bat); + u32 remaining_cap = get_unaligned_le32(&bat->bst.remaining_cap); + + lockdep_assert_held(&bat->lock); + + return full_cap != SPWR_BATTERY_VALUE_UNKNOWN && full_cap != 0 && + remaining_cap != SPWR_BATTERY_VALUE_UNKNOWN && + remaining_cap >= full_cap && + state == 0; +} + +static int spwr_battery_recheck_full(struct spwr_battery_device *bat) +{ + bool present; + u32 unit; + int status; + + mutex_lock(&bat->lock); + unit = get_unaligned_le32(&bat->bix.power_unit); + present = spwr_battery_present(bat); + + status = spwr_battery_update_bix_unlocked(bat); + if (status) + goto out; + + /* If battery has been attached, (re-)initialize alarm. */ + if (!present && spwr_battery_present(bat)) { + u32 cap_warn = get_unaligned_le32(&bat->bix.design_cap_warn); + + status = spwr_battery_set_alarm_unlocked(bat, cap_warn); + if (status) + goto out; + } + + /* + * Warn if the unit has changed. This is something we genuinely don't + * expect to happen, so make this a big warning. If it does, we'll + * need to add support for it. + */ + WARN_ON(unit != get_unaligned_le32(&bat->bix.power_unit)); + +out: + mutex_unlock(&bat->lock); + + if (!status) + power_supply_changed(bat->psy); + + return status; +} + +static int spwr_battery_recheck_status(struct spwr_battery_device *bat) +{ + int status; + + status = spwr_battery_update_bst(bat, false); + if (!status) + power_supply_changed(bat->psy); + + return status; +} + +static u32 spwr_notify_bat(struct ssam_event_notifier *nf, const struct ssam_event *event) +{ + struct spwr_battery_device *bat = container_of(nf, struct spwr_battery_device, notif); + int status; + + dev_dbg(&bat->sdev->dev, "power event (cid = %#04x, iid = %#04x, tid = %#04x)\n", + event->command_id, event->instance_id, event->target_id); + + switch (event->command_id) { + case SAM_EVENT_CID_BAT_BIX: + status = spwr_battery_recheck_full(bat); + break; + + case SAM_EVENT_CID_BAT_BST: + status = spwr_battery_recheck_status(bat); + break; + + case SAM_EVENT_CID_BAT_PROT: + /* + * TODO: Implement support for battery protection status change + * event. + */ + status = 0; + break; + + case SAM_EVENT_CID_BAT_DPTF: + /* + * TODO: Implement support for DPTF event. + */ + status = 0; + break; + + default: + return 0; + } + + return ssam_notifier_from_errno(status) | SSAM_NOTIF_HANDLED; +} + +static void spwr_battery_update_bst_workfn(struct work_struct *work) +{ + struct delayed_work *dwork = to_delayed_work(work); + struct spwr_battery_device *bat; + int status; + + bat = container_of(dwork, struct spwr_battery_device, update_work); + + status = spwr_battery_update_bst(bat, false); + if (status) { + dev_err(&bat->sdev->dev, "failed to update battery state: %d\n", status); + return; + } + + power_supply_changed(bat->psy); +} + +static void spwr_external_power_changed(struct power_supply *psy) +{ + struct spwr_battery_device *bat = power_supply_get_drvdata(psy); + + /* + * Handle battery update quirk: When the battery is fully charged (or + * charged up to the limit imposed by the UEFI battery limit) and the + * adapter is plugged in or removed, the EC does not send a separate + * event for the state (charging/discharging) change. Furthermore it + * may take some time until the state is updated on the battery. + * Schedule an update to solve this. + */ + + schedule_delayed_work(&bat->update_work, SPWR_AC_BAT_UPDATE_DELAY); +} + + +/* -- Properties. ----------------------------------------------------------- */ + +static const enum power_supply_property spwr_battery_props_chg[] = { + POWER_SUPPLY_PROP_STATUS, + POWER_SUPPLY_PROP_PRESENT, + POWER_SUPPLY_PROP_TECHNOLOGY, + POWER_SUPPLY_PROP_CYCLE_COUNT, + POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN, + POWER_SUPPLY_PROP_VOLTAGE_NOW, + POWER_SUPPLY_PROP_CURRENT_NOW, + POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN, + POWER_SUPPLY_PROP_CHARGE_FULL, + POWER_SUPPLY_PROP_CHARGE_NOW, + POWER_SUPPLY_PROP_CAPACITY, + POWER_SUPPLY_PROP_CAPACITY_LEVEL, + POWER_SUPPLY_PROP_MODEL_NAME, + POWER_SUPPLY_PROP_MANUFACTURER, + POWER_SUPPLY_PROP_SERIAL_NUMBER, +}; + +static const enum power_supply_property spwr_battery_props_eng[] = { + POWER_SUPPLY_PROP_STATUS, + POWER_SUPPLY_PROP_PRESENT, + POWER_SUPPLY_PROP_TECHNOLOGY, + POWER_SUPPLY_PROP_CYCLE_COUNT, + POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN, + POWER_SUPPLY_PROP_VOLTAGE_NOW, + POWER_SUPPLY_PROP_POWER_NOW, + POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN, + POWER_SUPPLY_PROP_ENERGY_FULL, + POWER_SUPPLY_PROP_ENERGY_NOW, + POWER_SUPPLY_PROP_CAPACITY, + POWER_SUPPLY_PROP_CAPACITY_LEVEL, + POWER_SUPPLY_PROP_MODEL_NAME, + POWER_SUPPLY_PROP_MANUFACTURER, + POWER_SUPPLY_PROP_SERIAL_NUMBER, +}; + +static int spwr_battery_prop_status(struct spwr_battery_device *bat) +{ + u32 state = get_unaligned_le32(&bat->bst.state); + u32 present_rate = get_unaligned_le32(&bat->bst.present_rate); + + lockdep_assert_held(&bat->lock); + + if (state & SAM_BATTERY_STATE_DISCHARGING) + return POWER_SUPPLY_STATUS_DISCHARGING; + + if (state & SAM_BATTERY_STATE_CHARGING) + return POWER_SUPPLY_STATUS_CHARGING; + + if (spwr_battery_is_full(bat)) + return POWER_SUPPLY_STATUS_FULL; + + if (present_rate == 0) + return POWER_SUPPLY_STATUS_NOT_CHARGING; + + return POWER_SUPPLY_STATUS_UNKNOWN; +} + +static int spwr_battery_prop_technology(struct spwr_battery_device *bat) +{ + lockdep_assert_held(&bat->lock); + + if (!strcasecmp("NiCd", bat->bix.type)) + return POWER_SUPPLY_TECHNOLOGY_NiCd; + + if (!strcasecmp("NiMH", bat->bix.type)) + return POWER_SUPPLY_TECHNOLOGY_NiMH; + + if (!strcasecmp("LION", bat->bix.type)) + return POWER_SUPPLY_TECHNOLOGY_LION; + + if (!strncasecmp("LI-ION", bat->bix.type, 6)) + return POWER_SUPPLY_TECHNOLOGY_LION; + + if (!strcasecmp("LiP", bat->bix.type)) + return POWER_SUPPLY_TECHNOLOGY_LIPO; + + return POWER_SUPPLY_TECHNOLOGY_UNKNOWN; +} + +static int spwr_battery_prop_capacity(struct spwr_battery_device *bat) +{ + u32 full_cap = sprw_battery_get_full_cap_safe(bat); + u32 remaining_cap = get_unaligned_le32(&bat->bst.remaining_cap); + + lockdep_assert_held(&bat->lock); + + if (full_cap == 0 || full_cap == SPWR_BATTERY_VALUE_UNKNOWN) + return -ENODATA; + + if (remaining_cap == SPWR_BATTERY_VALUE_UNKNOWN) + return -ENODATA; + + return remaining_cap * 100 / full_cap; +} + +static int spwr_battery_prop_capacity_level(struct spwr_battery_device *bat) +{ + u32 state = get_unaligned_le32(&bat->bst.state); + u32 remaining_cap = get_unaligned_le32(&bat->bst.remaining_cap); + + lockdep_assert_held(&bat->lock); + + if (state & SAM_BATTERY_STATE_CRITICAL) + return POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL; + + if (spwr_battery_is_full(bat)) + return POWER_SUPPLY_CAPACITY_LEVEL_FULL; + + if (remaining_cap <= bat->alarm) + return POWER_SUPPLY_CAPACITY_LEVEL_LOW; + + return POWER_SUPPLY_CAPACITY_LEVEL_NORMAL; +} + +static int spwr_battery_get_property(struct power_supply *psy, enum power_supply_property psp, + union power_supply_propval *val) +{ + struct spwr_battery_device *bat = power_supply_get_drvdata(psy); + u32 value; + int status; + + mutex_lock(&bat->lock); + + status = spwr_battery_update_bst_unlocked(bat, true); + if (status) + goto out; + + /* Abort if battery is not present. */ + if (!spwr_battery_present(bat) && psp != POWER_SUPPLY_PROP_PRESENT) { + status = -ENODEV; + goto out; + } + + switch (psp) { + case POWER_SUPPLY_PROP_STATUS: + val->intval = spwr_battery_prop_status(bat); + break; + + case POWER_SUPPLY_PROP_PRESENT: + val->intval = spwr_battery_present(bat); + break; + + case POWER_SUPPLY_PROP_TECHNOLOGY: + val->intval = spwr_battery_prop_technology(bat); + break; + + case POWER_SUPPLY_PROP_CYCLE_COUNT: + value = get_unaligned_le32(&bat->bix.cycle_count); + if (value != SPWR_BATTERY_VALUE_UNKNOWN) + val->intval = value; + else + status = -ENODATA; + break; + + case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN: + value = get_unaligned_le32(&bat->bix.design_voltage); + if (value != SPWR_BATTERY_VALUE_UNKNOWN) + val->intval = value * 1000; + else + status = -ENODATA; + break; + + case POWER_SUPPLY_PROP_VOLTAGE_NOW: + value = get_unaligned_le32(&bat->bst.present_voltage); + if (value != SPWR_BATTERY_VALUE_UNKNOWN) + val->intval = value * 1000; + else + status = -ENODATA; + break; + + case POWER_SUPPLY_PROP_CURRENT_NOW: + case POWER_SUPPLY_PROP_POWER_NOW: + value = get_unaligned_le32(&bat->bst.present_rate); + if (value != SPWR_BATTERY_VALUE_UNKNOWN) + val->intval = value * 1000; + else + status = -ENODATA; + break; + + case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN: + case POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN: + value = get_unaligned_le32(&bat->bix.design_cap); + if (value != SPWR_BATTERY_VALUE_UNKNOWN) + val->intval = value * 1000; + else + status = -ENODATA; + break; + + case POWER_SUPPLY_PROP_CHARGE_FULL: + case POWER_SUPPLY_PROP_ENERGY_FULL: + value = get_unaligned_le32(&bat->bix.last_full_charge_cap); + if (value != SPWR_BATTERY_VALUE_UNKNOWN) + val->intval = value * 1000; + else + status = -ENODATA; + break; + + case POWER_SUPPLY_PROP_CHARGE_NOW: + case POWER_SUPPLY_PROP_ENERGY_NOW: + value = get_unaligned_le32(&bat->bst.remaining_cap); + if (value != SPWR_BATTERY_VALUE_UNKNOWN) + val->intval = value * 1000; + else + status = -ENODATA; + break; + + case POWER_SUPPLY_PROP_CAPACITY: + val->intval = spwr_battery_prop_capacity(bat); + break; + + case POWER_SUPPLY_PROP_CAPACITY_LEVEL: + val->intval = spwr_battery_prop_capacity_level(bat); + break; + + case POWER_SUPPLY_PROP_MODEL_NAME: + val->strval = bat->bix.model; + break; + + case POWER_SUPPLY_PROP_MANUFACTURER: + val->strval = bat->bix.oem_info; + break; + + case POWER_SUPPLY_PROP_SERIAL_NUMBER: + val->strval = bat->bix.serial; + break; + + default: + status = -EINVAL; + break; + } + +out: + mutex_unlock(&bat->lock); + return status; +} + + +/* -- Alarm attribute. ------------------------------------------------------ */ + +static ssize_t alarm_show(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct power_supply *psy = dev_get_drvdata(dev); + struct spwr_battery_device *bat = power_supply_get_drvdata(psy); + int status; + + mutex_lock(&bat->lock); + status = sysfs_emit(buf, "%d\n", bat->alarm * 1000); + mutex_unlock(&bat->lock); + + return status; +} + +static ssize_t alarm_store(struct device *dev, struct device_attribute *attr, const char *buf, + size_t count) +{ + struct power_supply *psy = dev_get_drvdata(dev); + struct spwr_battery_device *bat = power_supply_get_drvdata(psy); + unsigned long value; + int status; + + status = kstrtoul(buf, 0, &value); + if (status) + return status; + + mutex_lock(&bat->lock); + + if (!spwr_battery_present(bat)) { + mutex_unlock(&bat->lock); + return -ENODEV; + } + + status = spwr_battery_set_alarm_unlocked(bat, value / 1000); + if (status) { + mutex_unlock(&bat->lock); + return status; + } + + mutex_unlock(&bat->lock); + return count; +} + +static DEVICE_ATTR_RW(alarm); + +static struct attribute *spwr_battery_attrs[] = { + &dev_attr_alarm.attr, + NULL, +}; +ATTRIBUTE_GROUPS(spwr_battery); + + +/* -- Device setup. --------------------------------------------------------- */ + +static void spwr_battery_init(struct spwr_battery_device *bat, struct ssam_device *sdev, + struct ssam_event_registry registry, const char *name) +{ + mutex_init(&bat->lock); + strncpy(bat->name, name, ARRAY_SIZE(bat->name) - 1); + + bat->sdev = sdev; + + bat->notif.base.priority = 1; + bat->notif.base.fn = spwr_notify_bat; + bat->notif.event.reg = registry; + bat->notif.event.id.target_category = sdev->uid.category; + bat->notif.event.id.instance = 0; + bat->notif.event.mask = SSAM_EVENT_MASK_STRICT; + bat->notif.event.flags = SSAM_EVENT_SEQUENCED; + + bat->psy_desc.name = bat->name; + bat->psy_desc.type = POWER_SUPPLY_TYPE_BATTERY; + bat->psy_desc.get_property = spwr_battery_get_property; + + INIT_DELAYED_WORK(&bat->update_work, spwr_battery_update_bst_workfn); +} + +static int spwr_battery_register(struct spwr_battery_device *bat) +{ + struct power_supply_config psy_cfg = {}; + __le32 sta; + int status; + + /* Make sure the device is there and functioning properly. */ + status = ssam_retry(ssam_bat_get_sta, bat->sdev, &sta); + if (status) + return status; + + if ((le32_to_cpu(sta) & SAM_BATTERY_STA_OK) != SAM_BATTERY_STA_OK) + return -ENODEV; + + /* Satisfy lockdep although we are in an exclusive context here. */ + mutex_lock(&bat->lock); + + status = spwr_battery_update_bix_unlocked(bat); + if (status) { + mutex_unlock(&bat->lock); + return status; + } + + if (spwr_battery_present(bat)) { + u32 cap_warn = get_unaligned_le32(&bat->bix.design_cap_warn); + + status = spwr_battery_set_alarm_unlocked(bat, cap_warn); + if (status) { + mutex_unlock(&bat->lock); + return status; + } + } + + mutex_unlock(&bat->lock); + + bat->psy_desc.external_power_changed = spwr_external_power_changed; + + switch (get_unaligned_le32(&bat->bix.power_unit)) { + case SAM_BATTERY_POWER_UNIT_mW: + bat->psy_desc.properties = spwr_battery_props_eng; + bat->psy_desc.num_properties = ARRAY_SIZE(spwr_battery_props_eng); + break; + + case SAM_BATTERY_POWER_UNIT_mA: + bat->psy_desc.properties = spwr_battery_props_chg; + bat->psy_desc.num_properties = ARRAY_SIZE(spwr_battery_props_chg); + break; + + default: + dev_err(&bat->sdev->dev, "unsupported battery power unit: %u\n", + get_unaligned_le32(&bat->bix.power_unit)); + return -EINVAL; + } + + psy_cfg.drv_data = bat; + psy_cfg.attr_grp = spwr_battery_groups; + + bat->psy = devm_power_supply_register(&bat->sdev->dev, &bat->psy_desc, &psy_cfg); + if (IS_ERR(bat->psy)) + return PTR_ERR(bat->psy); + + return ssam_notifier_register(bat->sdev->ctrl, &bat->notif); +} + + +/* -- Driver setup. --------------------------------------------------------- */ + +static int __maybe_unused surface_battery_resume(struct device *dev) +{ + return spwr_battery_recheck_full(dev_get_drvdata(dev)); +} +static SIMPLE_DEV_PM_OPS(surface_battery_pm_ops, NULL, surface_battery_resume); + +static int surface_battery_probe(struct ssam_device *sdev) +{ + const struct spwr_psy_properties *p; + struct spwr_battery_device *bat; + + p = ssam_device_get_match_data(sdev); + if (!p) + return -ENODEV; + + bat = devm_kzalloc(&sdev->dev, sizeof(*bat), GFP_KERNEL); + if (!bat) + return -ENOMEM; + + spwr_battery_init(bat, sdev, p->registry, p->name); + ssam_device_set_drvdata(sdev, bat); + + return spwr_battery_register(bat); +} + +static void surface_battery_remove(struct ssam_device *sdev) +{ + struct spwr_battery_device *bat = ssam_device_get_drvdata(sdev); + + ssam_notifier_unregister(sdev->ctrl, &bat->notif); + cancel_delayed_work_sync(&bat->update_work); +} + +static const struct spwr_psy_properties spwr_psy_props_bat1 = { + .name = "BAT1", + .registry = SSAM_EVENT_REGISTRY_SAM, +}; + +static const struct spwr_psy_properties spwr_psy_props_bat2_sb3 = { + .name = "BAT2", + .registry = SSAM_EVENT_REGISTRY_KIP, +}; + +static const struct ssam_device_id surface_battery_match[] = { + { SSAM_SDEV(BAT, 0x01, 0x01, 0x00), (unsigned long)&spwr_psy_props_bat1 }, + { SSAM_SDEV(BAT, 0x02, 0x01, 0x00), (unsigned long)&spwr_psy_props_bat2_sb3 }, + { }, +}; +MODULE_DEVICE_TABLE(ssam, surface_battery_match); + +static struct ssam_device_driver surface_battery_driver = { + .probe = surface_battery_probe, + .remove = surface_battery_remove, + .match_table = surface_battery_match, + .driver = { + .name = "surface_battery", + .pm = &surface_battery_pm_ops, + .probe_type = PROBE_PREFER_ASYNCHRONOUS, + }, +}; +module_ssam_device_driver(surface_battery_driver); + +MODULE_AUTHOR("Maximilian Luz "); +MODULE_DESCRIPTION("Battery driver for Surface System Aggregator Module"); +MODULE_LICENSE("GPL"); diff --git a/drivers/power/supply/surface_charger.c b/drivers/power/supply/surface_charger.c new file mode 100644 index 0000000..81a5b79 --- /dev/null +++ b/drivers/power/supply/surface_charger.c @@ -0,0 +1,282 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * AC driver for 7th-generation Microsoft Surface devices via Surface System + * Aggregator Module (SSAM). + * + * Copyright (C) 2019-2021 Maximilian Luz + */ + +#include +#include +#include +#include +#include +#include + +#include + + +/* -- SAM interface. -------------------------------------------------------- */ + +enum sam_event_cid_bat { + SAM_EVENT_CID_BAT_ADP = 0x17, +}; + +enum sam_battery_sta { + SAM_BATTERY_STA_OK = 0x0f, + SAM_BATTERY_STA_PRESENT = 0x10, +}; + +/* Get battery status (_STA). */ +SSAM_DEFINE_SYNC_REQUEST_CL_R(ssam_bat_get_sta, __le32, { + .target_category = SSAM_SSH_TC_BAT, + .command_id = 0x01, +}); + +/* Get platform power source for battery (_PSR / DPTF PSRC). */ +SSAM_DEFINE_SYNC_REQUEST_CL_R(ssam_bat_get_psrc, __le32, { + .target_category = SSAM_SSH_TC_BAT, + .command_id = 0x0d, +}); + + +/* -- Device structures. ---------------------------------------------------- */ + +struct spwr_psy_properties { + const char *name; + struct ssam_event_registry registry; +}; + +struct spwr_ac_device { + struct ssam_device *sdev; + + char name[32]; + struct power_supply *psy; + struct power_supply_desc psy_desc; + + struct ssam_event_notifier notif; + + struct mutex lock; /* Guards access to state below. */ + + __le32 state; +}; + + +/* -- State management. ----------------------------------------------------- */ + +static int spwr_ac_update_unlocked(struct spwr_ac_device *ac) +{ + u32 old = ac->state; + int status; + + lockdep_assert_held(&ac->lock); + + status = ssam_retry(ssam_bat_get_psrc, ac->sdev, &ac->state); + if (status < 0) + return status; + + return old != ac->state; +} + +static int spwr_ac_update(struct spwr_ac_device *ac) +{ + int status; + + mutex_lock(&ac->lock); + status = spwr_ac_update_unlocked(ac); + mutex_unlock(&ac->lock); + + return status; +} + +static int spwr_ac_recheck(struct spwr_ac_device *ac) +{ + int status; + + status = spwr_ac_update(ac); + if (status > 0) + power_supply_changed(ac->psy); + + return status >= 0 ? 0 : status; +} + +static u32 spwr_notify_ac(struct ssam_event_notifier *nf, const struct ssam_event *event) +{ + struct spwr_ac_device *ac; + int status; + + ac = container_of(nf, struct spwr_ac_device, notif); + + dev_dbg(&ac->sdev->dev, "power event (cid = %#04x, iid = %#04x, tid = %#04x)\n", + event->command_id, event->instance_id, event->target_id); + + /* + * Allow events of all targets/instances here. Global adapter status + * seems to be handled via target=1 and instance=1, but events are + * reported on all targets/instances in use. + * + * While it should be enough to just listen on 1/1, listen everywhere to + * make sure we don't miss anything. + */ + + switch (event->command_id) { + case SAM_EVENT_CID_BAT_ADP: + status = spwr_ac_recheck(ac); + return ssam_notifier_from_errno(status) | SSAM_NOTIF_HANDLED; + + default: + return 0; + } +} + + +/* -- Properties. ----------------------------------------------------------- */ + +static const enum power_supply_property spwr_ac_props[] = { + POWER_SUPPLY_PROP_ONLINE, +}; + +static int spwr_ac_get_property(struct power_supply *psy, enum power_supply_property psp, + union power_supply_propval *val) +{ + struct spwr_ac_device *ac = power_supply_get_drvdata(psy); + int status; + + mutex_lock(&ac->lock); + + status = spwr_ac_update_unlocked(ac); + if (status) + goto out; + + switch (psp) { + case POWER_SUPPLY_PROP_ONLINE: + val->intval = !!le32_to_cpu(ac->state); + break; + + default: + status = -EINVAL; + goto out; + } + +out: + mutex_unlock(&ac->lock); + return status; +} + + +/* -- Device setup. --------------------------------------------------------- */ + +static char *battery_supplied_to[] = { + "BAT1", + "BAT2", +}; + +static void spwr_ac_init(struct spwr_ac_device *ac, struct ssam_device *sdev, + struct ssam_event_registry registry, const char *name) +{ + mutex_init(&ac->lock); + strncpy(ac->name, name, ARRAY_SIZE(ac->name) - 1); + + ac->sdev = sdev; + + ac->notif.base.priority = 1; + ac->notif.base.fn = spwr_notify_ac; + ac->notif.event.reg = registry; + ac->notif.event.id.target_category = sdev->uid.category; + ac->notif.event.id.instance = 0; + ac->notif.event.mask = SSAM_EVENT_MASK_NONE; + ac->notif.event.flags = SSAM_EVENT_SEQUENCED; + + ac->psy_desc.name = ac->name; + ac->psy_desc.type = POWER_SUPPLY_TYPE_MAINS; + ac->psy_desc.properties = spwr_ac_props; + ac->psy_desc.num_properties = ARRAY_SIZE(spwr_ac_props); + ac->psy_desc.get_property = spwr_ac_get_property; +} + +static int spwr_ac_register(struct spwr_ac_device *ac) +{ + struct power_supply_config psy_cfg = {}; + __le32 sta; + int status; + + /* Make sure the device is there and functioning properly. */ + status = ssam_retry(ssam_bat_get_sta, ac->sdev, &sta); + if (status) + return status; + + if ((le32_to_cpu(sta) & SAM_BATTERY_STA_OK) != SAM_BATTERY_STA_OK) + return -ENODEV; + + psy_cfg.drv_data = ac; + psy_cfg.supplied_to = battery_supplied_to; + psy_cfg.num_supplicants = ARRAY_SIZE(battery_supplied_to); + + ac->psy = devm_power_supply_register(&ac->sdev->dev, &ac->psy_desc, &psy_cfg); + if (IS_ERR(ac->psy)) + return PTR_ERR(ac->psy); + + return ssam_notifier_register(ac->sdev->ctrl, &ac->notif); +} + + +/* -- Driver setup. --------------------------------------------------------- */ + +static int __maybe_unused surface_ac_resume(struct device *dev) +{ + return spwr_ac_recheck(dev_get_drvdata(dev)); +} +static SIMPLE_DEV_PM_OPS(surface_ac_pm_ops, NULL, surface_ac_resume); + +static int surface_ac_probe(struct ssam_device *sdev) +{ + const struct spwr_psy_properties *p; + struct spwr_ac_device *ac; + + p = ssam_device_get_match_data(sdev); + if (!p) + return -ENODEV; + + ac = devm_kzalloc(&sdev->dev, sizeof(*ac), GFP_KERNEL); + if (!ac) + return -ENOMEM; + + spwr_ac_init(ac, sdev, p->registry, p->name); + ssam_device_set_drvdata(sdev, ac); + + return spwr_ac_register(ac); +} + +static void surface_ac_remove(struct ssam_device *sdev) +{ + struct spwr_ac_device *ac = ssam_device_get_drvdata(sdev); + + ssam_notifier_unregister(sdev->ctrl, &ac->notif); +} + +static const struct spwr_psy_properties spwr_psy_props_adp1 = { + .name = "ADP1", + .registry = SSAM_EVENT_REGISTRY_SAM, +}; + +static const struct ssam_device_id surface_ac_match[] = { + { SSAM_SDEV(BAT, 0x01, 0x01, 0x01), (unsigned long)&spwr_psy_props_adp1 }, + { }, +}; +MODULE_DEVICE_TABLE(ssam, surface_ac_match); + +static struct ssam_device_driver surface_ac_driver = { + .probe = surface_ac_probe, + .remove = surface_ac_remove, + .match_table = surface_ac_match, + .driver = { + .name = "surface_ac", + .pm = &surface_ac_pm_ops, + .probe_type = PROBE_PREFER_ASYNCHRONOUS, + }, +}; +module_ssam_device_driver(surface_ac_driver); + +MODULE_AUTHOR("Maximilian Luz "); +MODULE_DESCRIPTION("AC driver for Surface System Aggregator Module"); +MODULE_LICENSE("GPL"); diff --git a/drivers/power/supply/tps65090-charger.c b/drivers/power/supply/tps65090-charger.c index 6b0098e..0990b2f 100644 --- a/drivers/power/supply/tps65090-charger.c +++ b/drivers/power/supply/tps65090-charger.c @@ -301,7 +301,7 @@ static int tps65090_charger_probe(struct platform_device *pdev) if (irq != -ENXIO) { ret = devm_request_threaded_irq(&pdev->dev, irq, NULL, - tps65090_charger_isr, 0, "tps65090-charger", cdata); + tps65090_charger_isr, IRQF_ONESHOT, "tps65090-charger", cdata); if (ret) { dev_err(cdata->dev, "Unable to register irq %d err %d\n", irq, diff --git a/drivers/power/supply/tps65217_charger.c b/drivers/power/supply/tps65217_charger.c index 814c2b8..ba33d16 100644 --- a/drivers/power/supply/tps65217_charger.c +++ b/drivers/power/supply/tps65217_charger.c @@ -238,7 +238,7 @@ static int tps65217_charger_probe(struct platform_device *pdev) for (i = 0; i < NUM_CHARGER_IRQS; i++) { ret = devm_request_threaded_irq(&pdev->dev, irq[i], NULL, tps65217_charger_irq, - 0, "tps65217-charger", + IRQF_ONESHOT, "tps65217-charger", charger); if (ret) { dev_err(charger->dev, diff --git a/drivers/power/supply/z2_battery.c b/drivers/power/supply/z2_battery.c index b1508fe..7ed4e4b 100644 --- a/drivers/power/supply/z2_battery.c +++ b/drivers/power/supply/z2_battery.c @@ -90,9 +90,6 @@ static void z2_batt_ext_power_changed(struct power_supply *batt_ps) static void z2_batt_update(struct z2_charger *charger) { int old_status = charger->bat_status; - struct z2_battery_info *info; - - info = charger->info; mutex_lock(&charger->work_lock); diff --git a/include/linux/mfd/abx500.h b/include/linux/mfd/abx500.h index 23040b6..7f07cfe 100644 --- a/include/linux/mfd/abx500.h +++ b/include/linux/mfd/abx500.h @@ -28,282 +28,6 @@ struct abx500_init_settings { u8 setting; }; -/* Battery driver related data */ -/* - * ADC for the battery thermistor. - * When using the ABx500_ADC_THERM_BATCTRL the battery ID resistor is combined - * with a NTC resistor to both identify the battery and to measure its - * temperature. Different phone manufactures uses different techniques to both - * identify the battery and to read its temperature. - */ -enum abx500_adc_therm { - ABx500_ADC_THERM_BATCTRL, - ABx500_ADC_THERM_BATTEMP, -}; - -/** - * struct abx500_res_to_temp - defines one point in a temp to res curve. To - * be used in battery packs that combines the identification resistor with a - * NTC resistor. - * @temp: battery pack temperature in Celsius - * @resist: NTC resistor net total resistance - */ -struct abx500_res_to_temp { - int temp; - int resist; -}; - -/** - * struct abx500_v_to_cap - Table for translating voltage to capacity - * @voltage: Voltage in mV - * @capacity: Capacity in percent - */ -struct abx500_v_to_cap { - int voltage; - int capacity; -}; - -/* Forward declaration */ -struct abx500_fg; - -/** - * struct abx500_fg_parameters - Fuel gauge algorithm parameters, in seconds - * if not specified - * @recovery_sleep_timer: Time between measurements while recovering - * @recovery_total_time: Total recovery time - * @init_timer: Measurement interval during startup - * @init_discard_time: Time we discard voltage measurement at startup - * @init_total_time: Total init time during startup - * @high_curr_time: Time current has to be high to go to recovery - * @accu_charging: FG accumulation time while charging - * @accu_high_curr: FG accumulation time in high current mode - * @high_curr_threshold: High current threshold, in mA - * @lowbat_threshold: Low battery threshold, in mV - * @overbat_threshold: Over battery threshold, in mV - * @battok_falling_th_sel0 Threshold in mV for battOk signal sel0 - * Resolution in 50 mV step. - * @battok_raising_th_sel1 Threshold in mV for battOk signal sel1 - * Resolution in 50 mV step. - * @user_cap_limit Capacity reported from user must be within this - * limit to be considered as sane, in percentage - * points. - * @maint_thres This is the threshold where we stop reporting - * battery full while in maintenance, in per cent - * @pcut_enable: Enable power cut feature in ab8505 - * @pcut_max_time: Max time threshold - * @pcut_flag_time: Flagtime threshold - * @pcut_max_restart: Max number of restarts - * @pcut_debounce_time: Sets battery debounce time - */ -struct abx500_fg_parameters { - int recovery_sleep_timer; - int recovery_total_time; - int init_timer; - int init_discard_time; - int init_total_time; - int high_curr_time; - int accu_charging; - int accu_high_curr; - int high_curr_threshold; - int lowbat_threshold; - int overbat_threshold; - int battok_falling_th_sel0; - int battok_raising_th_sel1; - int user_cap_limit; - int maint_thres; - bool pcut_enable; - u8 pcut_max_time; - u8 pcut_flag_time; - u8 pcut_max_restart; - u8 pcut_debounce_time; -}; - -/** - * struct abx500_charger_maximization - struct used by the board config. - * @use_maxi: Enable maximization for this battery type - * @maxi_chg_curr: Maximum charger current allowed - * @maxi_wait_cycles: cycles to wait before setting charger current - * @charger_curr_step delta between two charger current settings (mA) - */ -struct abx500_maxim_parameters { - bool ena_maxi; - int chg_curr; - int wait_cycles; - int charger_curr_step; -}; - -/** - * struct abx500_battery_type - different batteries supported - * @name: battery technology - * @resis_high: battery upper resistance limit - * @resis_low: battery lower resistance limit - * @charge_full_design: Maximum battery capacity in mAh - * @nominal_voltage: Nominal voltage of the battery in mV - * @termination_vol: max voltage upto which battery can be charged - * @termination_curr battery charging termination current in mA - * @recharge_cap battery capacity limit that will trigger a new - * full charging cycle in the case where maintenan- - * -ce charging has been disabled - * @normal_cur_lvl: charger current in normal state in mA - * @normal_vol_lvl: charger voltage in normal state in mV - * @maint_a_cur_lvl: charger current in maintenance A state in mA - * @maint_a_vol_lvl: charger voltage in maintenance A state in mV - * @maint_a_chg_timer_h: charge time in maintenance A state - * @maint_b_cur_lvl: charger current in maintenance B state in mA - * @maint_b_vol_lvl: charger voltage in maintenance B state in mV - * @maint_b_chg_timer_h: charge time in maintenance B state - * @low_high_cur_lvl: charger current in temp low/high state in mA - * @low_high_vol_lvl: charger voltage in temp low/high state in mV' - * @battery_resistance: battery inner resistance in mOhm. - * @n_r_t_tbl_elements: number of elements in r_to_t_tbl - * @r_to_t_tbl: table containing resistance to temp points - * @n_v_cap_tbl_elements: number of elements in v_to_cap_tbl - * @v_to_cap_tbl: Voltage to capacity (in %) table - * @n_batres_tbl_elements number of elements in the batres_tbl - * @batres_tbl battery internal resistance vs temperature table - */ -struct abx500_battery_type { - int name; - int resis_high; - int resis_low; - int charge_full_design; - int nominal_voltage; - int termination_vol; - int termination_curr; - int recharge_cap; - int normal_cur_lvl; - int normal_vol_lvl; - int maint_a_cur_lvl; - int maint_a_vol_lvl; - int maint_a_chg_timer_h; - int maint_b_cur_lvl; - int maint_b_vol_lvl; - int maint_b_chg_timer_h; - int low_high_cur_lvl; - int low_high_vol_lvl; - int battery_resistance; - int n_temp_tbl_elements; - const struct abx500_res_to_temp *r_to_t_tbl; - int n_v_cap_tbl_elements; - const struct abx500_v_to_cap *v_to_cap_tbl; - int n_batres_tbl_elements; - const struct batres_vs_temp *batres_tbl; -}; - -/** - * struct abx500_bm_capacity_levels - abx500 capacity level data - * @critical: critical capacity level in percent - * @low: low capacity level in percent - * @normal: normal capacity level in percent - * @high: high capacity level in percent - * @full: full capacity level in percent - */ -struct abx500_bm_capacity_levels { - int critical; - int low; - int normal; - int high; - int full; -}; - -/** - * struct abx500_bm_charger_parameters - Charger specific parameters - * @usb_volt_max: maximum allowed USB charger voltage in mV - * @usb_curr_max: maximum allowed USB charger current in mA - * @ac_volt_max: maximum allowed AC charger voltage in mV - * @ac_curr_max: maximum allowed AC charger current in mA - */ -struct abx500_bm_charger_parameters { - int usb_volt_max; - int usb_curr_max; - int ac_volt_max; - int ac_curr_max; -}; - -/** - * struct abx500_bm_data - abx500 battery management data - * @temp_under under this temp, charging is stopped - * @temp_low between this temp and temp_under charging is reduced - * @temp_high between this temp and temp_over charging is reduced - * @temp_over over this temp, charging is stopped - * @temp_now present battery temperature - * @temp_interval_chg temperature measurement interval in s when charging - * @temp_interval_nochg temperature measurement interval in s when not charging - * @main_safety_tmr_h safety timer for main charger - * @usb_safety_tmr_h safety timer for usb charger - * @bkup_bat_v voltage which we charge the backup battery with - * @bkup_bat_i current which we charge the backup battery with - * @no_maintenance indicates that maintenance charging is disabled - * @capacity_scaling indicates whether capacity scaling is to be used - * @abx500_adc_therm placement of thermistor, batctrl or battemp adc - * @chg_unknown_bat flag to enable charging of unknown batteries - * @enable_overshoot flag to enable VBAT overshoot control - * @auto_trig flag to enable auto adc trigger - * @fg_res resistance of FG resistor in 0.1mOhm - * @n_btypes number of elements in array bat_type - * @batt_id index of the identified battery in array bat_type - * @interval_charging charge alg cycle period time when charging (sec) - * @interval_not_charging charge alg cycle period time when not charging (sec) - * @temp_hysteresis temperature hysteresis - * @gnd_lift_resistance Battery ground to phone ground resistance (mOhm) - * @n_chg_out_curr number of elements in array chg_output_curr - * @n_chg_in_curr number of elements in array chg_input_curr - * @chg_output_curr charger output current level map - * @chg_input_curr charger input current level map - * @maxi maximization parameters - * @cap_levels capacity in percent for the different capacity levels - * @bat_type table of supported battery types - * @chg_params charger parameters - * @fg_params fuel gauge parameters - */ -struct abx500_bm_data { - int temp_under; - int temp_low; - int temp_high; - int temp_over; - int temp_now; - int temp_interval_chg; - int temp_interval_nochg; - int main_safety_tmr_h; - int usb_safety_tmr_h; - int bkup_bat_v; - int bkup_bat_i; - bool autopower_cfg; - bool ac_enabled; - bool usb_enabled; - bool no_maintenance; - bool capacity_scaling; - bool chg_unknown_bat; - bool enable_overshoot; - bool auto_trig; - enum abx500_adc_therm adc_therm; - int fg_res; - int n_btypes; - int batt_id; - int interval_charging; - int interval_not_charging; - int temp_hysteresis; - int gnd_lift_resistance; - int n_chg_out_curr; - int n_chg_in_curr; - int *chg_output_curr; - int *chg_input_curr; - const struct abx500_maxim_parameters *maxi; - const struct abx500_bm_capacity_levels *cap_levels; - struct abx500_battery_type *bat_type; - const struct abx500_bm_charger_parameters *chg_params; - const struct abx500_fg_parameters *fg_params; -}; - -enum { - NTC_EXTERNAL = 0, - NTC_INTERNAL, -}; - -int ab8500_bm_of_probe(struct device *dev, - struct device_node *np, - struct abx500_bm_data *bm); - int abx500_set_register_interruptible(struct device *dev, u8 bank, u8 reg, u8 value); int abx500_get_register_interruptible(struct device *dev, u8 bank, u8 reg, diff --git a/include/linux/power/bq27xxx_battery.h b/include/linux/power/bq27xxx_battery.h index 111a40d..a1aa681 100644 --- a/include/linux/power/bq27xxx_battery.h +++ b/include/linux/power/bq27xxx_battery.h @@ -33,6 +33,7 @@ enum bq27xxx_chip { BQ27Z561, BQ28Z610, BQ34Z100, + BQ78Z100, }; struct bq27xxx_device_info; @@ -53,7 +54,6 @@ struct bq27xxx_reg_cache { int capacity; int energy; int flags; - int power_avg; int health; }; diff --git a/include/linux/power_supply.h b/include/linux/power_supply.h index b495b43..be20398 100644 --- a/include/linux/power_supply.h +++ b/include/linux/power_supply.h @@ -381,8 +381,14 @@ struct power_supply_battery_info { extern struct atomic_notifier_head power_supply_notifier; extern int power_supply_reg_notifier(struct notifier_block *nb); extern void power_supply_unreg_notifier(struct notifier_block *nb); +#if IS_ENABLED(CONFIG_POWER_SUPPLY) extern struct power_supply *power_supply_get_by_name(const char *name); extern void power_supply_put(struct power_supply *psy); +#else +static inline void power_supply_put(struct power_supply *psy) {} +static inline struct power_supply *power_supply_get_by_name(const char *name) +{ return NULL; } +#endif #ifdef CONFIG_OF extern struct power_supply *power_supply_get_by_phandle(struct device_node *np, const char *property); @@ -483,12 +489,12 @@ static inline bool power_supply_is_amp_property(enum power_supply_property psp) case POWER_SUPPLY_PROP_CURRENT_NOW: case POWER_SUPPLY_PROP_CURRENT_AVG: case POWER_SUPPLY_PROP_CURRENT_BOOT: - return 1; + return true; default: break; } - return 0; + return false; } static inline bool power_supply_is_watt_property(enum power_supply_property psp) @@ -511,12 +517,12 @@ static inline bool power_supply_is_watt_property(enum power_supply_property psp) case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE: case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX: case POWER_SUPPLY_PROP_POWER_NOW: - return 1; + return true; default: break; } - return 0; + return false; } #ifdef CONFIG_POWER_SUPPLY_HWMON