Merge tag 'regulator-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

79f20778 · Linus Torvalds <[email protected]> · 2018-12-25 14:38:31 -08:00

Pull regulator updates from Mark Brown:
 "This has been a very busy release for the core, some fixes, one large
  new feature and a big bit of refactoring to update the GPIO API:

   - Support for coupled regulators from Dmitry Osipenko based on a
     prior attempt by Maciej Purski, allowing us to handle situations
     where the voltages on two regulators can't be too far apart from
     each other.

   - Conversion of the GPIO support in both drivers and the core to use
     GPIO descriptors rather than numbers, part of the overall project
     to remove GPIO numbers.

   - Support for standby mode suspend states from Andrei Stefanescu.

   - New drivers for Allwinner AXP209, Cirrus Logic Lochnagar and
     Microchip MPC16502"

* tag 'regulator-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (90 commits)
  regulator: tps65910: fix a missing check of return value
  regulator: mcp16502: Select REGMAP_I2C to fix build error
  regulator: convert to DEFINE_SHOW_ATTRIBUTE
  regulator: mcp16502: Fix missing n_voltages setting
  regulator: mcp16502: Use #ifdef CONFIG_PM_SLEEP around mcp16502_suspend/resume_noirq
  regulator: mcp16502: code cleanup
  regulator: act8945a-regulator: make symbol act8945a_pm static
  drivers/regulator: fix a missing check of return value
  regulator: act8945a-regulator: fix 'defined but not used' compiler warning
  regulator: axp20x: fix set_ramp_delay for AXP209/dcdc2
  regulator: mcp16502: add support for suspend
  mfd: axp20x: use explicit bit defines
  mfd: axp20x: Clean up included headers
  regulator: dts: enable soft-start and ramp delay for the OLinuXino Lime2
  dt-bindings: mfd: axp20x: Add software based soft_start for AXP209 LDO3
  regulator: axp20x: add software based soft_start for AXP209 LDO3
  dt-bindings: mfd: axp20x: add support for regulator-ramp-delay for AXP209
  regulator: axp20x: add support for set_ramp_delay for AXP209
  mfd: axp20x: name voltage ramping define properly
  regulator: mcp16502: add regulator driver for MCP16502
  ...

Commit: 79f20778fb228ae372cd7602745382fd4543ef31
Parents: d923fd6d · c3b57259

Merge commit. Changes below are compared with the first parent: d923fd6d.

Changes

59 files changed · +3141 −635

File	Status	Add	Del	Content
Documentation/devicetree/bindings/mfd/axp20x.txt	modified	+9	−0	View file
Documentation/devicetree/bindings/regulator/act8945a-regulator.txt	modified	+34	−0	View file
Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt	added	+82	−0	View file
Documentation/devicetree/bindings/regulator/mcp16502-regulator.txt	added	+143	−0	View file
Documentation/devicetree/bindings/regulator/regulator.txt	modified	+9	−3	View file
Documentation/driver-model/devres.txt	modified	+1	−0	View file
MAINTAINERS	modified	+7	−0	View file
arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts	modified	+2	−0	View file
arch/arm/mach-s3c64xx/mach-crag6410-module.c	modified	+15	−2	View file
drivers/gpio/gpiolib-devres.c	modified	+68	−12	View file
drivers/gpio/gpiolib.c	modified	+2	−0	View file
drivers/gpio/gpiolib.h	modified	+0	−6	View file
drivers/mfd/axp20x.c	modified	+7	−6	View file
drivers/mfd/wm8994-core.c	modified	+0	−9	View file
drivers/regulator/88pm8607.c	modified	+1	−1	View file
drivers/regulator/Kconfig	modified	+10	−0	View file
drivers/regulator/Makefile	modified	+1	−0	View file
drivers/regulator/act8945a-regulator.c	modified	+202	−3	View file
drivers/regulator/arizona-ldo1.c	modified	+0	−3	View file
drivers/regulator/as3711-regulator.c	modified	+1	−4	View file
drivers/regulator/axp20x-regulator.c	modified	+697	−179	View file
drivers/regulator/bd718x7-regulator.c	modified	+29	−4	View file
drivers/regulator/bd9571mwv-regulator.c	modified	+1	−9	View file
drivers/regulator/core.c	modified	+961	−238	View file
drivers/regulator/da9052-regulator.c	modified	+1	−1	View file
drivers/regulator/da9210-regulator.c	modified	+2	−2	View file
drivers/regulator/da9211-regulator.c	modified	+6	−0	View file
drivers/regulator/dbx500-prcmu.c	modified	+4	−31	View file
drivers/regulator/fixed.c	modified	+5	−1	View file
drivers/regulator/internal.h	modified	+2	−0	View file
drivers/regulator/lm363x-regulator.c	modified	+6	−2	View file
drivers/regulator/lochnagar-regulator.c	modified	+39	−11	View file
drivers/regulator/lp8788-ldo.c	modified	+6	−2	View file
drivers/regulator/max77686-regulator.c	modified	+19	−10	View file
drivers/regulator/max8952.c	modified	+7	−3	View file
drivers/regulator/max8973-regulator.c	modified	+7	−1	View file
drivers/regulator/max8997-regulator.c	modified	+1	−1	View file
drivers/regulator/mc13xxx-regulator-core.c	modified	+1	−1	View file
drivers/regulator/mcp16502.c	added	+552	−0	View file
drivers/regulator/of_regulator.c	modified	+51	−30	View file
drivers/regulator/palmas-regulator.c	modified	+4	−1	View file
drivers/regulator/pfuze100-regulator.c	modified	+2	−0	View file
drivers/regulator/qcom-rpmh-regulator.c	modified	+1	−1	View file
drivers/regulator/s2mps11.c	modified	+29	−25	View file
drivers/regulator/s5m8767.c	modified	+9	−2	View file
drivers/regulator/stpmic1_regulator.c	modified	+2	−2	View file
drivers/regulator/tps65090-regulator.c	modified	+6	−0	View file
drivers/regulator/tps65910-regulator.c	modified	+3	−1	View file
drivers/regulator/wm8350-regulator.c	modified	+2	−2	View file
drivers/regulator/wm8994-regulator.c	modified	+21	−12	View file
drivers/spi/spi-qcom-qspi.c	modified	+4	−4	View file
include/dt-bindings/regulator/active-semi,8945a-regulator.h	added	+30	−0	View file
include/linux/gpio/consumer.h	modified	+23	−0	View file
include/linux/mfd/axp20x.h	modified	+2	−2	View file
include/linux/mfd/wm8994/pdata.h	modified	+0	−3	View file
include/linux/regulator/consumer.h	modified	+1	−1	View file
include/linux/regulator/driver.h	modified	+6	−3	View file
include/linux/regulator/machine.h	modified	+3	−0	View file
include/linux/regulator/pfuze100.h	modified	+2	−1	View file

Only the first 600 diff lines are shown. Download the complete patch.

Documentation/devicetree/bindings/mfd/axp20x.txt

View file

diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
index 188f037..2af4ff9 100644
--- a/Documentation/devicetree/bindings/mfd/axp20x.txt
+++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
@@ -32,6 +32,15 @@ Required properties:
 - interrupt-controller: The PMIC has its own internal IRQs
 - #interrupt-cells: Should be set to 1
 
+Supported common regulator properties, see ../regulator/regulator.txt for
+more information:
+- regulator-ramp-delay: sets the ramp up delay in uV/us
+			AXP20x/DCDC2: 1600, 800
+			AXP20x/LDO3:  1600, 800
+- regulator-soft-start:	enable the output at the lowest possible voltage and
+			only then set the desired voltage
+			AXP20x/LDO3: software-based implementation
+
 Optional properties:
 - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
 		      AXP152/20X: range:  750-1875, Default: 1.5 MHz

Documentation/devicetree/bindings/regulator/act8945a-regulator.txt

View file

diff --git a/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt b/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt
index ac955de..4017527 100644
--- a/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt
@@ -15,11 +15,17 @@ Optional input supply properties:
   - inl67-supply: The input supply for REG_LDO3 and REG_LDO4
 
 Any standard regulator properties can be used to configure the single regulator.
+regulator-initial-mode, regulator-allowed-modes and regulator-mode could be
+specified using mode values from dt-bindings/regulator/active-semi,8945a-regulator.h
+file.
 
 The valid names for regulators are:
 	REG_DCDC1, REG_DCDC2, REG_DCDC3, REG_LDO1, REG_LDO2, REG_LDO3, REG_LDO4.
 
 Example:
+
+#include <dt-bindings/regulator/active-semi,8945a-regulator.h>
+
 	pmic@5b {
 		compatible = "active-semi,act8945a";
 		reg = <0x5b>;
@@ -32,6 +38,18 @@ Example:
 				regulator-min-microvolt = <1350000>;
 				regulator-max-microvolt = <1350000>;
 				regulator-always-on;
+
+				regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_FIXED>,
+							  <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+				regulator-initial-mode = <ACT8945A_REGULATOR_MODE_FIXED>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-min-microvolt=<1400000>;
+					regulator-suspend-max-microvolt=<1400000>;
+					regulator-changeable-in-suspend;
+					regulator-mode=<ACT8945A_REGULATOR_MODE_LOWPOWER>;
+				};
 			};
 
 			vdd_1v2_reg: REG_DCDC2 {
@@ -39,6 +57,14 @@ Example:
 				regulator-min-microvolt = <1100000>;
 				regulator-max-microvolt = <1300000>;
 				regulator-always-on;
+
+				regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_FIXED>,
+							  <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+				regulator-initial-mode = <ACT8945A_REGULATOR_MODE_FIXED>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
 			};
 
 			vdd_3v3_reg: REG_DCDC3 {
@@ -53,6 +79,14 @@ Example:
 				regulator-min-microvolt = <2500000>;
 				regulator-max-microvolt = <2500000>;
 				regulator-always-on;
+
+				regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_NORMAL>,
+							  <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+				regulator-initial-mode = <ACT8945A_REGULATOR_MODE_NORMAL>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
 			};
 
 			vdd_3v3_lp_reg: REG_LDO2 {

Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt

View file

diff --git a/Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt b/Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt
new file mode 100644
index 0000000..91974e6
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt
@@ -0,0 +1,82 @@
+Cirrus Logic Lochnagar Audio Development Board
+
+Lochnagar is an evaluation and development board for Cirrus Logic
+Smart CODEC and Amp devices. It allows the connection of most Cirrus
+Logic devices on mini-cards, as well as allowing connection of
+various application processor systems to provide a full evaluation
+platform.  Audio system topology, clocking and power can all be
+controlled through the Lochnagar, allowing the device under test
+to be used in a variety of possible use cases.
+
+This binding document describes the binding for the regulator portion
+of the driver.
+
+Also see these documents for generic binding information:
+  [1] Regulator: ../regulator/regulator.txt
+
+This binding must be part of the Lochnagar MFD binding:
+  [2] ../mfd/cirrus,lochnagar.txt
+
+Optional sub-nodes:
+
+  - VDDCORE : Initialisation data for the VDDCORE regulator, which
+    supplies the CODECs digital core if it has no build regulator for that
+    purpose.
+      Required Properties:
+      - compatible : One of the following strings:
+                     "cirrus,lochnagar2-vddcore"
+      - SYSVDD-supply: Primary power supply for the Lochnagar.
+
+  - MICVDD : Initialisation data for the MICVDD regulator, which
+    supplies the CODECs MICVDD.
+      Required Properties:
+      - compatible : One of the following strings:
+                     "cirrus,lochnagar2-micvdd"
+      - SYSVDD-supply: Primary power supply for the Lochnagar.
+
+  - MIC1VDD, MIC2VDD : Initialisation data for the MICxVDD supplies.
+      Required Properties:
+      - compatible : One of the following strings:
+                     "cirrus,lochnagar2-mic1vdd", "cirrus,lochnagar2-mic2vdd"
+      Optional Properties:
+      - cirrus,micbias-input : A property selecting which of the CODEC
+        minicard micbias outputs should be used, valid values are 1 - 4.
+      - MICBIAS1-supply, MICBIAS2-supply: Regulator supplies for the
+        MICxVDD outputs, supplying the digital microphones, normally
+        supplied from the attached CODEC.
+
+  - VDD1V8 : Recommended fixed regulator for the VDD1V8 regulator, which supplies the
+    CODECs analog and 1.8V digital supplies.
+      Required Properties:
+      - compatible : Should be set to "regulator-fixed"
+      - regulator-min-microvolt : Should be set to 1.8V
+      - regulator-max-microvolt : Should be set to 1.8V
+      - regulator-boot-on
+      - regulator-always-on
+      - vin-supply : Should be set to same supply as SYSVDD
+
+Example:
+
+lochnagar {
+	lochnagar-micvdd: MICVDD {
+		compatible = "cirrus,lochnagar2-micvdd";
+
+		SYSVDD-supply = <&wallvdd>;
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	lochnagar-vdd1v8: VDD1V8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VDD1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+
+		vin-supply = <&wallvdd>;
+	};
+};
+

Documentation/devicetree/bindings/regulator/mcp16502-regulator.txt

View file

diff --git a/Documentation/devicetree/bindings/regulator/mcp16502-regulator.txt b/Documentation/devicetree/bindings/regulator/mcp16502-regulator.txt
new file mode 100644
index 0000000..b8f843f
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/mcp16502-regulator.txt
@@ -0,0 +1,143 @@
+MCP16502 PMIC
+
+Required properties:
+- compatible: "microchip,mcp16502"
+- reg: I2C slave address
+- lpm-gpios: GPIO for LPM pin. Note that this GPIO *must* remain high during
+	     suspend-to-ram, keeping the PMIC into HIBERNATE mode.
+- regulators: A node that houses a sub-node for each regulator within
+              the device. Each sub-node is identified using the node's
+              name. The content of each sub-node is defined by the
+              standard binding for regulators; see regulator.txt.
+
+Regualtors of MCP16502 PMIC:
+1) VDD_IO	- Buck (1.2 - 3.7 V)
+2) VDD_DDR	- Buck (0.6 - 1.85 V)
+3) VDD_CORE	- Buck (0.6 - 1.85 V)
+4) VDD_OTHER	- BUCK (0.6 - 1.85 V)
+5) LDO1		- LDO  (1.2 - 3.7 V)
+6) LDO2		- LDO  (1.2 - 3.7 V)
+
+Regulator modes:
+2 - FPWM: higher precision, higher consumption
+4 - AutoPFM: lower precision, lower consumption
+
+Each regulator is defined using the standard binding for regulators.
+
+Example:
+
+mcp16502@5b {
+	compatible = "microchip,mcp16502";
+	reg = <0x5b>;
+	status = "okay";
+	lpm-gpios = <&pioBU 7 GPIO_ACTIVE_HIGH>;
+
+	regulators {
+		VDD_IO {
+			regulator-name = "VDD_IO";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3700000>;
+			regulator-initial-mode = <2>;
+			regulator-allowed-modes = <2>, <4>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+				regulator-mode = <4>;
+			};
+		};
+
+		VDD_DDR {
+			regulator-name = "VDD_DDR";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <1850000>;
+			regulator-initial-mode = <2>;
+			regulator-allowed-modes = <2>, <4>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+
+			regulator-state-mem {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+		};
+
+		VDD_CORE {
+			regulator-name = "VDD_CORE";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <1850000>;
+			regulator-initial-mode = <2>;
+			regulator-allowed-modes = <2>, <4>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+				regulator-mode = <4>;
+			};
+		};
+
+		VDD_OTHER {
+			regulator-name = "VDD_OTHER";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <1850000>;
+			regulator-initial-mode = <2>;
+			regulator-allowed-modes = <2>, <4>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+				regulator-mode = <4>;
+			};
+		};
+
+		LDO1 {
+			regulator-name = "LDO1";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3700000>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+			};
+		};
+
+		LDO2 {
+			regulator-name = "LDO2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3700000>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+			};
+		};
+
+	};
+};

Documentation/devicetree/bindings/regulator/regulator.txt

View file

diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt
index a7cd368..0a3f087 100644
--- a/Documentation/devicetree/bindings/regulator/regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/regulator.txt
@@ -33,13 +33,16 @@ Optional properties:
   decreases of any level. This is useful for regulators with exponential
   voltage changes.
 - regulator-soft-start: Enable soft start so that voltage ramps slowly
+- regulator-state-standby sub-root node for Standby mode
+  : equivalent with standby Linux sleep state, which provides energy savings
+  with a relatively quick transition back time.
 - regulator-state-mem sub-root node for Suspend-to-RAM mode
   : suspend to memory, the device goes to sleep, but all data stored in memory,
   only some external interrupt can wake the device.
 - regulator-state-disk sub-root node for Suspend-to-DISK mode
   : suspend to disk, this state operates similarly to Suspend-to-RAM,
   but includes a final step of writing memory contents to disk.
-- regulator-state-[mem/disk] node has following common properties:
+- regulator-state-[mem/disk/standby] node has following common properties:
 	- regulator-on-in-suspend: regulator should be on in suspend state.
 	- regulator-off-in-suspend: regulator should be off in suspend state.
 	- regulator-suspend-min-microvolt: minimum voltage may be set in
@@ -76,8 +79,11 @@ Optional properties:
 - regulator-coupled-with: Regulators with which the regulator
   is coupled. The linkage is 2-way - all coupled regulators should be linked
   with each other. A regulator should not be coupled with its supplier.
-- regulator-coupled-max-spread: Max spread between voltages of coupled regulators
-  in microvolts.
+- regulator-coupled-max-spread: Array of maximum spread between voltages of
+  coupled regulators in microvolts, each value in the array relates to the
+  corresponding couple specified by the regulator-coupled-with property.
+- regulator-max-step-microvolt: Maximum difference between current and target
+  voltages that can be changed safely in a single step.
 
 Deprecated properties:
 - regulator-compatible: If a regulator chip contains multiple

Documentation/driver-model/devres.txt

View file

diff --git a/Documentation/driver-model/devres.txt b/Documentation/driver-model/devres.txt
index 43681ca..fc4cc24 100644
--- a/Documentation/driver-model/devres.txt
+++ b/Documentation/driver-model/devres.txt
@@ -254,6 +254,7 @@ GPIO
   devm_gpiod_get_index_optional()
   devm_gpiod_get_optional()
   devm_gpiod_put()
+  devm_gpiod_unhinge()
   devm_gpiochip_add_data()
   devm_gpiochip_remove()
   devm_gpio_request()

MAINTAINERS

View file

diff --git a/MAINTAINERS b/MAINTAINERS
index 7808b16..f0f0c23 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -9891,6 +9891,13 @@ M:	Ludovic Desroches <[email protected]>
 S:	Maintained
 F:	drivers/mmc/host/atmel-mci.c
 
+MICROCHIP MCP16502 PMIC DRIVER
+M:	Andrei Stefanescu <[email protected]>
+L:	[email protected] (moderated for non-subscribers)
+S:	Maintained
+F:	Documentation/devicetree/bindings/regulator/mcp16502-regulator.txt
+F:	drivers/regulator/mcp16502.c
+
 MICROCHIP MCP3911 ADC DRIVER
 M:	Marcus Folkesson <[email protected]>
 M:	Kent Gustavsson <[email protected]>

arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts

View file

diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
index b828677..ffafe97 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
+++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
@@ -245,6 +245,8 @@
 	regulator-min-microvolt = <2800000>;
 	regulator-max-microvolt = <2800000>;
 	regulator-name = "vddio-csi0";
+	regulator-soft-start;
+	regulator-ramp-delay = <1600>;
 };
 
 &reg_ldo4 {

arch/arm/mach-s3c64xx/mach-crag6410-module.c

View file

diff --git a/arch/arm/mach-s3c64xx/mach-crag6410-module.c b/arch/arm/mach-s3c64xx/mach-crag6410-module.c
index 5aa4728..76c4855 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410-module.c
+++ b/arch/arm/mach-s3c64xx/mach-crag6410-module.c
@@ -194,8 +194,8 @@ static struct wm8994_pdata wm8994_pdata = {
 		0x3,          /* IRQ out, active high, CMOS */
 	},
 	.ldo = {
-		 { .enable = S3C64XX_GPN(6), .init_data = &wm8994_ldo1, },
-		 { .enable = S3C64XX_GPN(4), .init_data = &wm8994_ldo2, },
+		 { .init_data = &wm8994_ldo1, },
+		 { .init_data = &wm8994_ldo2, },
 	},
 };
 
@@ -203,6 +203,18 @@ static const struct i2c_board_info wm1277_devs[] = {
 	{ I2C_BOARD_INFO("wm8958", 0x1a),  /* WM8958 is the superset */
 	  .platform_data = &wm8994_pdata,
 	  .irq = GLENFARCLAS_PMIC_IRQ_BASE + WM831X_IRQ_GPIO_2,
+	  .dev_name = "wm8958",
+	},
+};
+
+static struct gpiod_lookup_table wm8994_gpiod_table = {
+	.dev_id = "i2c-wm8958", /* I2C device name */
+	.table = {
+		GPIO_LOOKUP("GPION", 6,
+			    "wlf,ldo1ena", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("GPION", 4,
+			    "wlf,ldo2ena", GPIO_ACTIVE_HIGH),
+		{ },
 	},
 };
 
@@ -381,6 +393,7 @@ static int wlf_gf_module_probe(struct i2c_client *i2c,
 
 	gpiod_add_lookup_table(&wm5102_reva_gpiod_table);
 	gpiod_add_lookup_table(&wm5102_gpiod_table);
+	gpiod_add_lookup_table(&wm8994_gpiod_table);
 
 	if (i < ARRAY_SIZE(gf_mods)) {
 		dev_info(&i2c->dev, "%s revision %d\n",

drivers/gpio/gpiolib-devres.c

View file

diff --git a/drivers/gpio/gpiolib-devres.c b/drivers/gpio/gpiolib-devres.c
index 0195936..0acc2cc 100644
--- a/drivers/gpio/gpiolib-devres.c
+++ b/drivers/gpio/gpiolib-devres.c
@@ -98,15 +98,28 @@ struct gpio_desc *__must_check devm_gpiod_get_index(struct device *dev,
 	struct gpio_desc **dr;
 	struct gpio_desc *desc;
 
+	desc = gpiod_get_index(dev, con_id, idx, flags);
+	if (IS_ERR(desc))
+		return desc;
+
+	/*
+	 * For non-exclusive GPIO descriptors, check if this descriptor is
+	 * already under resource management by this device.
+	 */
+	if (flags & GPIOD_FLAGS_BIT_NONEXCLUSIVE) {
+		struct devres *dres;
+
+		dres = devres_find(dev, devm_gpiod_release,
+				   devm_gpiod_match, &desc);
+		if (dres)
+			return desc;
+	}
+
 	dr = devres_alloc(devm_gpiod_release, sizeof(struct gpio_desc *),
 			  GFP_KERNEL);
-	if (!dr)
+	if (!dr) {
+		gpiod_put(desc);
 		return ERR_PTR(-ENOMEM);
-
-	desc = gpiod_get_index(dev, con_id, idx, flags);
-	if (IS_ERR(desc)) {
-		devres_free(dr);
-		return desc;
 	}
 
 	*dr = desc;
@@ -140,15 +153,28 @@ struct gpio_desc *devm_gpiod_get_from_of_node(struct device *dev,
 	struct gpio_desc **dr;
 	struct gpio_desc *desc;
 
+	desc = gpiod_get_from_of_node(node, propname, index, dflags, label);
+	if (IS_ERR(desc))
+		return desc;
+
+	/*
+	 * For non-exclusive GPIO descriptors, check if this descriptor is
+	 * already under resource management by this device.
+	 */
+	if (dflags & GPIOD_FLAGS_BIT_NONEXCLUSIVE) {
+		struct devres *dres;
+
+		dres = devres_find(dev, devm_gpiod_release,
+				   devm_gpiod_match, &desc);
+		if (dres)
+			return desc;
+	}
+
 	dr = devres_alloc(devm_gpiod_release, sizeof(struct gpio_desc *),
 			  GFP_KERNEL);
-	if (!dr)
+	if (!dr) {
+		gpiod_put(desc);
 		return ERR_PTR(-ENOMEM);
-
-	desc = gpiod_get_from_of_node(node, propname, index, dflags, label);
-	if (IS_ERR(desc)) {
-		devres_free(dr);
-		return desc;
 	}
 
 	*dr = desc;
@@ -321,6 +347,36 @@ void devm_gpiod_put(struct device *dev, struct gpio_desc *desc)
 EXPORT_SYMBOL(devm_gpiod_put);
 
 /**
+ * devm_gpiod_unhinge - Remove resource management from a gpio descriptor
+ * @dev:	GPIO consumer
+ * @desc:	GPIO descriptor to remove resource management from
+ *
+ * Remove resource management from a GPIO descriptor. This is needed when
+ * you want to hand over lifecycle management of a descriptor to another
+ * mechanism.
+ */
+
+void devm_gpiod_unhinge(struct device *dev, struct gpio_desc *desc)
+{
+	int ret;
+
+	if (IS_ERR_OR_NULL(desc))
+		return;
+	ret = devres_destroy(dev, devm_gpiod_release,
+			     devm_gpiod_match, &desc);
+	/*
+	 * If the GPIO descriptor is requested as nonexclusive, we
+	 * may call this function several times on the same descriptor
+	 * so it is OK if devres_destroy() returns -ENOENT.
+	 */
+	if (ret == -ENOENT)
+		return;
+	/* Anything else we should warn about */
+	WARN_ON(ret);
+}
+EXPORT_SYMBOL(devm_gpiod_unhinge);
+
+/**
  * devm_gpiod_put_array - Resource-managed gpiod_put_array()
  * @dev:	GPIO consumer
  * @descs:	GPIO descriptor array to dispose of

drivers/gpio/gpiolib.c

View file

diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
index a2cbb47..985c09c 100644
--- a/drivers/gpio/gpiolib.c
+++ b/drivers/gpio/gpiolib.c
@@ -4205,6 +4205,8 @@ struct gpio_desc *gpiod_get_from_of_node(struct device_node *node,
 	transitory = flags & OF_GPIO_TRANSITORY;
 
 	ret = gpiod_request(desc, label);
+	if (ret == -EBUSY && (flags & GPIOD_FLAGS_BIT_NONEXCLUSIVE))
+		return desc;
 	if (ret)
 		return ERR_PTR(ret);
 

drivers/gpio/gpiolib.h

View file

diff --git a/drivers/gpio/gpiolib.h b/drivers/gpio/gpiolib.h
index 087d865..bc57f0d 100644
--- a/drivers/gpio/gpiolib.h
+++ b/drivers/gpio/gpiolib.h
@@ -201,12 +201,6 @@ int gpiod_set_array_value_complex(bool raw, bool can_sleep,
 				  struct gpio_array *array_info,
 				  unsigned long *value_bitmap);
 
-/* This is just passed between gpiolib and devres */
-struct gpio_desc *gpiod_get_from_of_node(struct device_node *node,
-					 const char *propname, int index,
-					 enum gpiod_flags dflags,
-					 const char *label);
-
 extern struct spinlock gpio_lock;
 extern struct list_head gpio_devices;
 

drivers/mfd/axp20x.c

View file

diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
index 0be511d..e1450a5 100644
--- a/drivers/mfd/axp20x.c
+++ b/drivers/mfd/axp20x.c
@@ -16,20 +16,21 @@
  * published by the Free Software Foundation.
  */
 
-#include <linux/err.h>
+#include <linux/acpi.h>

This diff is incomplete. Download the complete patch.