| 1 | ===========================================
|
| 2 | IBM's Journaled File System (JFS) for Linux
|
| 3 | ===========================================
|
| 4 |
|
| 5 | JFS Homepage: http://jfs.sourceforge.net/
|
| 6 |
|
| 7 | The following mount options are supported:
|
| 8 |
|
| 9 | (*) == default
|
| 10 |
|
| 11 | iocharset=name
|
| 12 | Character set to use for converting from Unicode to
|
| 13 | ASCII. The default is to do no conversion. Use
|
| 14 | iocharset=utf8 for UTF-8 translations. This requires
|
| 15 | CONFIG_NLS_UTF8 to be set in the kernel .config file.
|
| 16 | iocharset=none specifies the default behavior explicitly.
|
| 17 |
|
| 18 | resize=value
|
| 19 | Resize the volume to <value> blocks. JFS only supports
|
| 20 | growing a volume, not shrinking it. This option is only
|
| 21 | valid during a remount, when the volume is mounted
|
| 22 | read-write. The resize keyword with no value will grow
|
| 23 | the volume to the full size of the partition.
|
| 24 |
|
| 25 | nointegrity
|
| 26 | Do not write to the journal. The primary use of this option
|
| 27 | is to allow for higher performance when restoring a volume
|
| 28 | from backup media. The integrity of the volume is not
|
| 29 | guaranteed if the system abnormally abends.
|
| 30 |
|
| 31 | integrity(*)
|
| 32 | Commit metadata changes to the journal. Use this option to
|
| 33 | remount a volume where the nointegrity option was
|
| 34 | previously specified in order to restore normal behavior.
|
| 35 |
|
| 36 | errors=continue
|
| 37 | Keep going on a filesystem error.
|
| 38 | errors=remount-ro(*)
|
| 39 | Remount the filesystem read-only on an error.
|
| 40 | errors=panic
|
| 41 | Panic and halt the machine if an error occurs.
|
| 42 |
|
| 43 | uid=value
|
| 44 | Override on-disk uid with specified value
|
| 45 | gid=value
|
| 46 | Override on-disk gid with specified value
|
| 47 | umask=value
|
| 48 | Override on-disk umask with specified octal value. For
|
| 49 | directories, the execute bit will be set if the corresponding
|
| 50 | read bit is set.
|
| 51 |
|
| 52 | discard=minlen, discard/nodiscard(*)
|
| 53 | This enables/disables the use of discard/TRIM commands.
|
| 54 | The discard/TRIM commands are sent to the underlying
|
| 55 | block device when blocks are freed. This is useful for SSD
|
| 56 | devices and sparse/thinly-provisioned LUNs. The FITRIM ioctl
|
| 57 | command is also available together with the nodiscard option.
|
| 58 | The value of minlen specifies the minimum blockcount, when
|
| 59 | a TRIM command to the block device is considered useful.
|
| 60 | When no value is given to the discard option, it defaults to
|
| 61 | 64 blocks, which means 256KiB in JFS.
|
| 62 | The minlen value of discard overrides the minlen value given
|
| 63 | on an FITRIM ioctl().
|
| 64 |
|
| 65 | The JFS mailing list can be subscribed to by using the link labeled
|
| 66 | "Mail list Subscribe" at our web page http://jfs.sourceforge.net/
|